Green's function method (GFM) and mathematical solution for coupled equations of transport problem during convective drying

The green's function method in quantum statistics

Simulations that are meant to determine the steady-state distribution of a diffusible solute such as oxygen in tissues have typically used finite difference methods to solve the diffusion equation. Finite difference methods require a tissue mesh with enough points to resolve oxygen gradients near and between discrete blood vessels. The large number of points that are typically required can make these calculations very slow. In this paper, we investigate a numerical method known as the Green's function method which is not bound by the same constraint. The Green's function method is expected to yield an accurate oxygen distribution more quickly by requiring fewer mesh points. Both methods were applied to calculate the steady state oxygen distribution in a model simulation region. When the Green's function calculation used meshes with 1/2, 1/4 and, 1/8 of the resolution required for the finite-difference mesh, there was good agreement with the finite difference calculation in all cases. When the volume of the domain was increased 8-fold the Green's function method was able to calculate the O2 field in 22 minutes, whereas the finite difference calculation is expected to take approximately 1 week. The number of steps required for the Green's function calculation increases quadratically with the number of points in the tissue mesh. As a result, small meshes are calculated very quickly using Green's functions, while for larger mesh sizes this method experiences a significant decrease in efficiency.

A mathematical model of simultaneous heat and moisture transfer is developed for convective drying of building material. A rectangular brick is considered for sample object. Finite-difference method with semi-implicit scheme is used for solving the transient governing heat and mass transfer equation. Convective boundary condition is used, as the product is exposed in hot air. The heat and mass transfer equations are coupled through diffusion coefficient which is assumed as the function of temperature of the product. Set of algebraic equations are generated through space and time discretization. The discretized algebraic equations are solved by Gauss–Siedel method via iteration. Grid and time independent studies are performed for finding the optimum number of nodal points and time steps respectively. A MATLAB computer code is developed to solve the heat and mass transfer equations simultaneously. Transient heat and mass transfer simulations are performed to find the temperature and moisture distribution inside the brick.

An analytic and numerical solution with spectral Green's function method for transport equation in spherical geometry

The elastic response of a vacancy in a semi-infinite fcc copper lattice containing a free surface is calculated by using a new multiscale Green's function method. The method treats the lattice distortion near the vacancy at the atomistic level and the free surface at the macroscopic continuum level in the same formalism. The lattice is modeled using the lattice statics Green's function that fully accounts for the discrete atomistic structure of the lattice and can model a large crystallite containing a million atoms without excessive CPU effort. The method is especially useful for modeling the elastic response of nanocrystals containing point defects in which surfaces and interfaces play important roles. The method bridges the length scales seamlessly by relating the microscopic lattice distortion near a point defect to measurable macroscopic parameters of the solid such as the strain and the displacement field at a free surface. Using the interatomic potential derived by Cleri and Rosato, the lattice distortion, relaxation energy, and relaxation volume due to a vacancy are calculated in an otherwise perfect copper lattice for a million-atom model containing a free (100) surface. The calculated value of the relaxation volume is in excellent agreement with the observed value. Numerical results are also presented for the strain and the displacement fields at the free surface due to a vacancy and the interaction energy between a vacancy and the free surface in anisotropic semi-infinite copper.

Resonance plays a key role in the formation of many physical phenomena. The complex-scaled Green's function method provides a powerful tool for exploring resonance. In this paper, we combine this method with the theory describing deformed nuclei with the formalism presented. Taking $^{45}\text{S}$ as an example, we elaborate numerical details and demonstrate how to determine the resonance parameters. The results are compared with those obtained by the complex scaling method and the coupled-channel method and satisfactory agreement is obtained. In particular, the present scheme focuses on the advantages of the complex scaling method and the Green's function method and is more suitable for the exploration of resonance.

The formulation of the Green's-function method, recently suggested by Ziman, for solving the energy-band problem in a so-called "muffin-tin" potential (zero outside spheres representing the various atoms, and spherically symmetrical within each sphere) is transformed to a form very much like that of the Augmented-plane-wave (APW) method, but cannot be transformed exactly into the APW formulation. The wave function set up by the Green's-function method is a superposition of plane waves satisfying the wave equation inside as well as outside the spheres representing the atoms, having a discontinuity of slope at the surfaces of the atomic spheres, enough to produce the correct solution of the Schr\"odinger problem outside the spheres. To get correct wave functions inside the atoms, one would have to construct augmented plane waves from these plane waves.

We have calculated the Debye-Waller factor (DWF) of Cu from a model that was used successfully in earlier calculations of anharmonicity by Cowley and Shukla. The present calculation has been carried out using quasiharmonic theory, the lowest-order (λ2) anharmonic perturbation theory, and a Green's function (GF) method which sums an infinite series of the λ2−type anharmonic terms. The static approximation ω → 0 in the cubic contribution to the self-energy of the GF, introduced in the earlier work on the DWF by Shukla and Hubschle is further justified by showing that in the high-temperature limit the exact results for the λ2 anharmonic contributions (cubic and quartic) to the Helmholtz free energy are given in this approximation. Results for the DWF are also obtained for a modified version of the Morse potential with λ2 perturbation theory (PT) and the GF method. The GF results are in excellent agreement with the experimental Mossbauer and X-ray data in the entire temperature range, 300 K  T  120...

A multiphase model was developed to simulate heat and mass transfer during the baking process of flat bread (Sangak bread) by considering volume changes. In the proposed model, the equations of heat and mass transfer for liquid (water) and gas (vapor andCO2) phases were developed based onFourier's,Fick's andDarcy's laws, respectively. In addition, the effect of evaporation–condensation phenomenon was considered using the nonequilibrium relation of evaporation rate in the mass and heat transfer equations. The quantity of specific heat and density of each mesh was predicted using series and parallel models, and values of unknown parameters were estimated using the standard least square method. The nonlinear partial differential equations of the model were solved by using the finite element method byCOMSOLMultiphysics software. The changes in bread thickness were determined by ImageJsoftware. The model validation was also accomplished by comparing the predicted temperature and moisture content with the experimental results. The highR2and the low root mean squared error between experimental and predicted data confirmed the validity of the developed mathematical model.Practical ApplicationsThe uniformity of the product quality and the energy loss during the baking process has always been considered as a great challenge in the baking industry. In recent years, there has been increasing demand for minimally processed and near‐fresh quality products. To produce the part‐baked Sangak bread, the dough fully processes and baking occurs to at level in which, the texture properly forms and low color changes occur. Nowadays, it is essential to find methods based on equations, mathematical modeling and engineering principles to improve process control. In order to develop these models, the profound understanding of the procedures during the baking, particularly, mass and energy transfer are essential. Since, there are few researches on evaporation‐condensation and volume change in contact baking; it is important to understand its mechanism for exploiting this phenomenon in the food industries.

The fracture behaviors of nanoscale sp-bonded materials have been studied using the molecular dynamics and lattice Green's function methods. The initial atomic structures of the crack are determined both from the elastic solutions as well as from those by lattice Green's function method for the infinite systems. Firstly, we calculate the Green function for the defective lattice, with dislocation and crack, by solving the Dyson equation, appropriate for absolute zero temperature, After the lattice Green functions of the absolute zero temperature have been determined, the lattice parameters and interatomic force constants are adjusted to fit to materials at temperature T. In general, we have found that the lattice trapping and stress intensity factors for dislocation emission K Ile , The fracture and strength properties are also investigated for the nanocrystailine materials like semiconductor quantum wire and nanotubes. The O(N) tight-binding molecular dynamics (TBMD) method is used to analyze the reconstruction of atomic bonding near the crack tip as well as the cleaved surface. We compare the fracture behavior of nanoscale materials with those of corresponding bulk-size materials.

<sec><p indent="0mm">Exotic nuclei far from the β stability line have become important scientific goals in the studies of experimental physics at large scientific facilities and theoretical research due to the rich new physics. In these exotic nuclei, the neutron or proton Fermi level is close to the continuum threshold. The pairing correlation could scatter the valence neutrons or protons into the continuum. This leads to the extended neutron or proton density distributions in these exotic nuclei. Therefore, properly describing the pairing correlation and continuum is crucial for studying the structures and properties of these exotic nuclei. The Hartree-Fock-Bogoliubov (HFB) theory is one of the promising tools for describing exotic nuclei. In this theory, people usually solve the HFB equation directly in the coordinate space or the Woods-Saxon basis. In the coordinate space, when employing box boundary conditions to discretize the continuum, the behavior of the wave functions at the boundaries will be affected by the size of the box. Meanwhile, one could not obtain the energy and width of the resonant states directly from the discretized continuum states. The Green’s function (GF) is a simple and effective tool for handling the continuum, which has been widely used in nuclear structure research. The GF can be established by using the wave functions that satisfy the equation of motion and the proper bound boundary conditions for the bound and continuum states. Then one can use the loop integral of the GF on the complex energy plane to construct the particle density and level density. In this way, the continuum states can be included in the density with proper boundary conditions, and thus the extended density distribution can be properly described. Furthermore, the GF on the complex energy plane and the level density can be used to identify the resonant states directly. </sec><sec> This paper briefly reviews the development of the GF method in the continuum density functional theory, focusing on its application in describing halo phenomena and single-particle resonance states in exotic nuclei. For the description of the halo phenomena, this review takes the neutron-rich Zr as examples to show the results given by Skyrme HFB calculations with the GF method. The extended neutron particle and pair density distributions can be more properly described by the GF method, compared to the box-discretized method. The self-consistency to deal with the pairing correlation and the continuum is important to determine the asymptotic neutron particle and pair density distributions. Furthermore, with the level density obtained by the loop integral of the GF on the complex energy plane, one can describe both the bound and resonant states on the same footing. Recently, in the relativistic mean field theory, a new method to obtain precise information for the resonant energy and width is proposed by using directly the poles of the GF on the complex energy plane. This helps explain the conservation and breaking of pseudospin symmetry in the nucleon single-particle levels. Additionally, Green’s function method is easily compatible with various theoretical models, thus in the future it can be further applied to describe the exotic nuclear collective resonances and nuclear reaction processes. </sec>

Ab initio green's function calculations on highly conducting polymers: Effects of electron correlation and aperiodicity

Thermal and water management in irrigating lands in the arid and semi-arid regions

The Modified Global Green's Function Method (MGGFM) is an integral technique that is characterized by good accuracy in the evaluation of boundary fluxes. This method uses only projections of the Green's Function for the solution of the discrete problem and this is the origin of the term 'Modified' of its name. In this paper the local strategy for calculating the projections of Green's function using de Finite Element Method (FEM) are detailed. The numerical examples show some aspects of the method that had not yet been observed and good results for the flux in all nodes of the mesh.

This paper, on one hand, is an introduction to thermo‐field dynamics (TFD), on the other hand a derivation of some interesting features of Green's functions in the frame of thermo‐field dynamics. It is proved that in the language of TFD, Green's functions at finite temperature take a very simple form. Through the applications of TFD to many‐body systems it is shown that TFD is a straightforward method in dealing with finite temperature many‐body systems. As an application of Green's function method in TFD, we derive a Kogan‐type formula for the non‐equilibrium dynamic conductivity or laser‐pulse heated condensed matters, where electrons and ions are held at different temperatures.