Ground Moving Target Imaging and Motion Parameter Estimation With Airborne Dual-Channel CSSAR

The airborne coherent multi-input multi-output (MIMO) radar benefiting from coherent integration (including intra-channel integration and inter-channel integration) of multi-channel echoes can obtain superior detection performance for high-speed maneuvering targets. However, due to the coupling motion characteristic between multiple airborne platforms and high-speed targets, the range walk (RW) and Doppler walk (DW) will occur within the intra-channel integration. Besides, the inter-channel signals also exist envelope and phase differences, which will lead to the difficulty in multi-channel integration. We make contributions towards addressing these limitations. On the one hand, we establish a three-dimensional (3-D) geometrical model for high-speed maneuvering target detection with airborne coherent MIMO radar and derive the mathematical expression of radar echoes, while the generalized Radon-Fourier transform (GRFT) is utilized to simultaneously correct the RW and DW for acquiring intra-channel integration. On the other hand, we analyze the properties of GRFT outputs and propose a GRFT-domain integration method to achieve the multi-channel coherent integration. More specifically, the proposed method first constructs a set of coupling equations for the estimation of target motion parameters (i.e., position, velocity and acceleration), then, the target's motion parameters can be estimated by Newton-Raphson method and solving the linear equations. Second, in order to settle the envelope and phase differences between multi-channel echoes, the envelope alignment and phase compensation functions of inter-channel echoes are constituted based on the estimated parameters. Finally, the coherent accumulation of multi-channel echoes can be implemented. Numerical simulations demonstrate the effectiveness of the proposed method.

This paper presents a study on signal modeling for airborne multichannel circular stripmap synthetic aperture radar (CSSAR)-ground moving target indication (GMTI) systems with relatively high resolution. High resolution is an important trend of synthetic aperture radar (SAR), which means higher accuracy requirement of range history and longer synthetic aperture time. It's known that targets are probably experience accelerations as the synthetic aperture time increases. Therefore, compared with the systems of lower resolution, the target signal modeling of high-resolution systems becomes more challenging. Besides, the coupling relationship among a target's motion and position parameters becomes more complicated due to the existence of accelerations. In this paper, a fourth-order range history model of a moving target is developed. Moreover, the target signal model is established, and the along-track interferometric (ATI) phase history is derived to reveal the coupling relationship among a target's motion and position parameters.

Moving target brings out the different position shifts and defocusing across the image sequences acquired by circular synthetic aperture radar (CSAR) due to the Doppler shift and range smear effects. In this paper, a novel moving target detection approach for single-channel CSAR is proposed based on deep neural network (DNN). A dual-channel densely connected convolutional network (DenseNet) in consideration of complex-valued information is exploited for distinguishing the ground clutter and moving target. In terms of limited CSAR measure data set available for training the DNN network, simulated moving target samples are generated and fused into the measured ones under the various motion parameters. Finally, experiments have demonstrated that the proposed DenseNet for single-channel CSAR system processes an accepted detection performance and effectively overcomes the insufficiency of the limited dataset applications.

We present a new method for estimating the motion parameters of a target from its inverse synthetic aperture radar (ISAR) signature. This method uses the phase of the target's echo transfer function to calculate a focal quality indicator while avoiding two-dimensional Fourier processing. The focal quality indicator reaches the global minimum of a parametric motion surface when the phase is compensated with the target's actual motion parameters. The presence of an absolute minimum without local minima guarantees that the estimated motion parameters are an accurate representation of the target's motion and allows the use of a simple search procedure. Polynomial fitting is incorporated to the new method to improve the robustness by reducing estimation errors due to the finite order of the parametric motion model.

The synthetic-wideband and pulse repetition frequency jittering radar systems are receiving increasing attention due to the relatively low construction costs and good anti-jamming performance. However, the inter-pulse random hopping of the carrier frequency and pulse repetition frequency introduces challenges to the long-time coherent integration and motion parameter estimation of the high-speed weak targets for these radar systems. A modified generalized Radon Fourier transform for weak target detection and motion parameter estimation is proposed. The proposed method can achieve full coherent integration gain for the high-speed weak target and has a good parameter estimation accuracy. After the target motion has been well compensated, the well-focused high-resolution range profile of the target can be obtained by synthetic-wideband processing. The effectiveness of the proposed method is verified by Monte Carlo simulations. In addition, experimental data collected using an X-band radar system are processed and analyzed to illustrate the practical performance of the proposed method.

Inverse synthetic aperture radar (ISAR) imaging is one of the important high- resolution radar applications for moving target detection and identification. The radial velocity, radial acceleration, and acceleration rate of maneuvering targets can cause range cell migration and Doppler variation in the received signals, which will degrade the imaging quality. Therefore, these parameters should be estimated and compensated before imaging. In low signal-to-noise ratio (SNR) conditions, the conventional motion parameter estimation and compensation algorithms for maneuvering targets do not work properly. To effectively detect and identify the maneuvering targets in low SNR conditions, a new radar imaging algorithm is proposed. The major contributions are as follows: 1) a novel algorithm for envelope migration correction is proposed with adjacent cross correlation function; 2) the target's motion parameters are estimated with the operations of Keystone transform and time-frequency transform to the adjacent cross correlation; 3) a theoretical analysis of the impact of motion parameters on the envelope migration is made, then cross-range phase estimation with the adjacent cross function is presented; 4) based on the estimated motion parameters of targets, a new algorithm for high-resolution ISAR imaging is developed.

Determining accurate location with Synthetic Aperture Radar (SAR) images is hindered not only by the limited resolution of the image but also by the non-rectangular nature of the process that produces the image, and the presence of multiple returns from di§erent height objects at the same range. Three dimensional SAR volume measurements can di§erentiate di§erent height scatterers but imaging methods are limited by the measurement scenario. Interpolation of images and volumes can normalize the collected data but can add inaccuracy to pixel and voxel impulse response (IPR) and localization estimates. Regions of best achievable accuracy deÖne the imaging algorithm performance envelope. Ideal localization occurs at the estimation bound of modeled point scatterers, and is also indicated by pixel and voxel size or IPR main lobe width. The performance envelope of SAR measurement scenarios, radar parameters, and imaging and estimation algorithms can reÖne system parameters of accurate localization. Use of analogous Circular and Linear SAR (CSAR and LSAR) scenarios enables joint trade-o§ of áight path along with imaging parameters. An ideal spherical construct underlies joint CSAR and LSAR, two and three dimensional SAR scenarios. This construct also ties CSAR and LSAR imaging to spherical ray-trace creation of phase history. For di§erent scenarios deÖned through a spherical model of parameters, localization performance of the imaging envelope, IPR and estimation accuracy are examined. Along with sample size and ideal chirp waveform sampling, the azimuth and elevation aperture is varied to include ideal and sub-sampling, and extension to achieve un-aliased images and volumes. Methods expanding the envelope are investigated.

Circular synthetic aperture radar (CSAR) has attracted much attention in the field of high-resolution SAR imaging. However, the CSAR image focusing is affected by the motion deviations of platform. In the processing of experimental CSAR data to deal with motion errors, the main way is using setup calibrators, which restricts its widespread applications. In this paper, based on the estimation of motion errors, an autofocus CSAR imaging strategy is proposed without using any setup calibrator. The first step is to split the entire aperture into several subapertures, the second step is to process the data in subapertures with an autofocus backprojection method, and the last step is to obtain the final CSAR image by merging the subimages obtained from the subaperture processing. The CSAR data processing results prove that the proposed strategy can remove the motion errors accurately and acquire well-focused CSAR images.

The main focus of this paper is on the estimation of target motion parameters using bearing measurements. Here, based on a linearization of measurements, a recursive least squares (RLS) solution is developed. The performance of the proposed method is compared to PLE which uses the same approach in measurement linearization. Simulation results show the excellence of the proposed method over the PLE, and RLS results are in vicinity of the CRLB.

Multi-channel synthetic aperture radar (SAR) systems is widely used in ground motion target indication and motion parameter estimation. This paper presents a new unambiguous speed estimation algorithm for multi-channel SAR systems. This paper presents a novel unambiguous velocity estimation algorithm for multichannel SAR systems. The proposed velocity estimation algorithm is a multistage procedure: the first stage is to generate a group of multichannel data with the reduced PRF; in the second stage, adaptive clutter suppression and velocity estimation using spatial spectral processing technique are applied for the two groups of multichannel data to calculate two ambiguity velocities for each moving target. Finally, the unambiguous radial velocity can be estimated using the two ambiguity velocities. The effectiveness of the proposed unambiguous velocity estimation approach is verified by simulated multichannel SAR data.

Multistatic pseudolinear target motion analysis using hybrid measurements

An airborne circular synthetic aperture radar system captured data for a 5 km diameter area over 31 orbits. For this challenge problem, the phase history for 56 targets was extracted from the larger data set and placed on a DVD for public release. The targets include 33 civilian vehicles of which many are repeated models, facilitating training and classification experiments. The remaining targets include an open area and 22 reflectors for scattering and calibration research. The circular synthetic aperture radar provides 360 degrees of azimuth around each target. For increased elevation content, the collection contains two nine-orbit volumetric series, where the sensor reduces altitude between each orbit. Researchers are challenged to further the art of focusing, 3D imaging, and target discrimination for circular synthetic aperture radar.

Circular synthetic aperture radar (CSAR) is a high resolution 2D and 3D imaging mode, to obtain the demand of all observation information. Circular motion trajectory make motion compensation problem is very difficult. However, existing method, such as autofocus back projection (ABP) algorithm, cannot effectively solve the problem of motion compensation in CSAR. In this paper, an autofocus algorithm based on minimum entropy is used to solve this problem. It can accurately estimate phase errors in CSAR. The simulated CSAR data are used to validate performance of minimum entropy autofocus (MEA) algorithm.

In this paper, we propose the two-dimensional imaging response of three-dimensional moving target via synthetic aperture radar (SAR) with back-projection imaging algorithm. Firstly, we analyzed the imaging response for each single echo, which is the intersection of Doppler isodop and iso-range contour. Then, we come up with a focus condition for moving target SAR imaging. Besides, we find that the Doppler frequency will cause a shift and the motion trail of moving target will draw a curve in the imaging result over synthetic aperture time. Meanwhile, we provide the numerical simulation experiments of moving point targets via linear SAR and circular SAR with X-band and THz-band, respectively, to verify the conclusion of moving target imaging response.

Circular synthetic aperture radar (CSAR) can obtain more complete scattering characteristics by observing the target with different azimuth angles. Therefore, extracting the complete structure of the target from CSAR images is of great significance for accurate interpretation. At present, the artificial target extraction based on CSAR images mostly uses anisotropic scattering features. For special targets such as buildings, as the walls and the ground form dihedral corner structures, there are also obvious strong scattering features such as double-scattering lines in SAR images. Therefore, combining the strong scattering features of buildings at specific aspects with anisotropic scattering characteristics at different aspects can obtain better extraction results, and how to extract these features accurately and efficiently is the key point. Based on this, this paper proposes a novel method for building contour extraction based on CSAR images. For strong scattering features, a fast fuzzy C-means (FCM) clustering algorithm was used to extract them. For anisotropic scattering features, aspect entropy was used to characterize the anisotropy degree, and K-means clustering was combined to extract. Finally, a more accurate result is obtained by merging the two feature extraction results. In order to verify the effectiveness and practicability of the proposed method, a lot of measured data acquired by the self-developed airborne L-band and Ku-band CSAR systems were processed. The experiments show that, compared with state-of-the-art algorithms, the proposed method can obtain more accurate results in less time.