High‐Efficiency Transmissive Programmable Metasurface for Multimode OAM Generation

Transmissive programmable metasurface can offer notable benefits for the precise agile manipulation of electromagnetic (EM) waves, which is a promising candidate for radar detection, wireless communications, and spectral imaging. However, most previous studies typically face the challenge of narrow bandwidth and are constrained by relatively simple and single functionality. Here, an ultra‐wideband (UWB) transmissive programmable metasurface is proposed to conduct agile multifunctional EM modulation. The meta‐atom is designed with a butterfly‐shaped configuration and manipulated using two pin diodes, demonstrating high‐efficiency transmission with low insertion loss less than 1 dB and stable phase difference of 180° from 15.77 to 28.59 GHz, ranging from Ku to Ka‐band with a fractional bandwidth up to 57.7%. The transmissive programmable metasurface is further constructed, and its effectiveness for multifunctional EM modulation is verified both numerically and experimentally, which can conduct different functionalities, including near‐field holographic imaging at lower‐frequency Ku‐band and far‐field high‐purity orbital angular momentum (OAM) generation at higher‐frequency Ka‐band. The proposed strategy may enrich the functionalities of programmable metasurfaces, as well as open a new pathway toward UWB multifunctional applications.

Traditional wireless links employing OAM (orbital angular momentum) beams make use of their spatial orthogonality in order to increase their spectral efficiency, by carrying a separate data stream on each beam. This requires that the OAM antenna axes are aligned with the line of sight of the link, and are capable of radiating and receiving high-purity orthogonal OAM beams. Due to the deep spatial nulls of these beams (except the zero-order OAM beam) on their axes, the received signal strengths are much lower than from conventional beams of comparable-sized antennas, limiting the signal-to-noise ratio (SNR) and the reach of such links, or requiring very large receive antennas in terms of wavelengths.Here we describe an alternative technique for recovering received OAM beams based on pseudo-Doppler techniques [1]-[3] which avoid the above limitations of traditional OAM links. In this work, the receiving antennas are not aligned with the OAM beam axes, so the received signals are stronger, the receivers and their antennas are fewer and simpler, and the reach is longer than in traditional wireless OAM links. We demonstrate for the first time, by simulations and experiments performed on an outdoor 100m link at 28 GHz, that it is possible to recover 4 independent data streams carried in a common 20MHz channel on 4 co-aperture OAM beams using the technique developed in [1], with only 2 receiver chains. The transmitting OAM antenna radiates all OAM beams with the same cone angles and the 2 receiving antennas are set on their peaks off-axis in the far field, 20cm apart and tangent to the OAM cones, unlike in traditional OAM wireless links [4]. Salient aspects of the pseudo-Doppler OAM recovery algorithm, its simulation in an end-to-end link, and key design features of the demonstration hardware and signal-processing are presented.

As a pathbreaking approach to generate orbital angular momentum (OAM) beam, uniform circular array (UCA) has been extensively researched and applied. However, the impact of the imperfect UCA (IUCA) converted from a UCA with the position of antenna elements on the purity of the generated OAM beam is rarely considered. In order to verify the effect of position deviation on the OAM beam, this letter deduces the analysis model of the IUCA and the OAM mode purity model. The OAM mode purity refers to the weight of the intensity of the "expected OAM mode." Numerical simulation results show that the OAM beam generated by IUCA is a superposition of OAM beams with a series of different modes, and this results in a certain OAM beam received being contaminated. Compared with the radius deviation, the azimuth deviation of antenna elements has more obvious influence on the OAM mode purity. Moreover, low-mode OAM beams are more suitable for long-distance transmission. Properly increasing the antenna array radius can improve the purity of high-order OAM modes.

Orbital angular momentum (OAM) beams have recently attracted attention due to their intrinsic properties and their many novelty applications. The use of dielectric metasurfaces as highly efficient and ultra-thin functional optical platforms for OAM beam generation has been discussed in detail in earlier research. However, reflective all-dielectric metasurfaces for high quality OAM beam generation have been rarely investigated. In this work, a high-quality OAM beam generator applying an all-dielectric reflective metasurface is proposed, with an operation waveband from 1500 to 1600 nm. Simulation results show that good quality OAM beams (mode purity ∼99%) can be generated with high efficiency (conversion rate >97%) and high reflectance (>0.8). With such superior performance, the proposed reflective all-dielectric metasurface can provide new possibilities in free-space optical communication systems.

Many emerging technologies, such as ultra-massive multiple-input multiple-output (UM-MIMO), terahertz (THz) communications are under active discussion as promising technologies to support the extremely high access rate and superior network capacity in the future sixth-generation (6G) mobile communication systems. However, such technologies are still facing many challenges for practical implementation. In particular, UM-MIMO and THz communication require extremely large number of radio frequency (RF) chains, and hence suffering from prohibitive hardware cost and complexity. In this article, we introduce a new paradigm to address the above issues, namely wireless communication enabled by programmable metasurfaces, by exploiting the powerful capability of metasurfaces in manipulating electromagnetic waves. We will first introduce the basic concept of programmable metasurfaces, followed by the promising paradigm shift in future wireless communication systems enabled by programmable metasurfaces. In particular, we propose two prospective paradigms of applying programmable metasurfaces in wireless transceivers: namely RF chain-free transmitter and space-down-conversion receiver, which both have great potential to simplify the architecture and reduce the hardware cost of future wireless transceivers. Furthermore, we present the design architectures, preliminary experimental results and main advantages of these new paradigms and discuss their potential opportunities and challenges toward ultra-massive 6G communications with low hardware complexity, low cost, and high energy efficiency.

Vector orbital angular momentum (OAM) beams, described by higher-order Poincaré (HOP) sphere, are generalized forms of waves carrying OAM with an inhomogeneous polarization of wavefronts. We construct all-dielectric metasurfaces with adjustable amplitude, polarization, and phase to generate arbitrary vector OAM beams. The metasurface is composed of two pairs of silicon nanopillars arranged alternately. Using the interference effect of the four meta-atoms related to the circular polarization, combined with the propagation and geometric phases, two OAM beams with controlled amplitude, phase, and equal topological charge but opposite signs can be obtained under the incidence of orthogonally circularly polarized lights. For the x linearly polarized light, arbitrary vector OAM beams on the HOP sphere are generated via the superposition of the above OAM beams. Additionally, the evolution process of the beam on the longitude and latitude of the Poincaré sphere is revealed by changing the amplitude and phase of the two OAM beams. This work provides a simple, effective, and flexible method for realizing vector OAM beams while having potential implications for the generation and manipulation of vectorial light fields at the micro-nano scale.

Over the past two decades, an extensive research effort has been devoted to elastic metamaterials, structured artificial materials at subwavelength scales, for elastic wave manipulations in solids. Due to the extreme values of material parameters, negative and/or positive, they achieved, the applications can range from wave and/or vibration attenuations, wave guiding and imaging, enhanced sensing, to invisible cloaking. However, conventional passive metamaterials have limitations, i.e. they can only be operated in narrow frequency regions and their functions are usually locked into space or with minor tunabilities once fabricated, lacking real time reconfigurabilities. Those limitations strongly hinder them from practical usages. With the rapid development of smart materials and structures, more and more intelligent elements are being introduced into wave propagation, vibration and sound control systems. The piezoelectric shunting technique is one well known method that receives considerable attention. In this dissertation, by leveraging the circuit control concept, both analog and digital, we propose some circuit controlled active/adaptive/hybrid/programmable metamaterials and metasurfaces for unprecedent elastic wave manipulations. Analytical, numerically and experimentally approaches are combined throughout the dissertation to illustrate design concepts, characterize wave propagation properties, and valid the designs. Specifically, active elastic metamaterials with tunable stiffness in local resonators are first designed for tunable wave and/or vibration mitigations. We then extend this concept to achieve super broadband wave attenuations with frequency-dependent stiffness elements. By introducing the variable stiffness elements to the host medium, a hybrid metamaterial is developed for switched ON/OFF wave propagations and broadband negative refractions. Based on a developed approximate transformation method, an active metamaterial is designed and placed on a plate to achieve spatially varying effective mass densities for broadband elastic trajectory control. Finally, a programmable metasurface with ultrathin-thickness is demonstrated for broadband, real-time and multifunctional wavefront manipulations in a plate. The active, adaptive, hybrid, and programmable elastic metamaterials and/or metasurfaces are still in their infant stages. The examples presented in the dissertation are transformable to different length and time scales and could serve as efficient and powerful tools in exploring some unconventional wave phenomenon in solid structures, i.e. by using concepts in quantum mechanics, where passive approaches are significantly limited. The designs could also immediately open new possibilities in elastic wave control devices including, but not limited to structural health monitoring, stealth technology, active noise control, as well as medical instrumentation and imaging.

Orbital angular momentum (OAM) beams have attracted great attention owing to their excellent performances in imaging and communication. In this paper, a dual-arm Archimedean spiral antenna (DASA) is proposed to generate multiple OAM states with positive and negative values by feeding at the inner and outer ends, respectively. The topological charge of radiated vortex waves is reconfigurable by tuning the operating frequency. Dual-mode OAM states are generated at different working frequencies (l = ±1 at 3 GHz, l = ±2 at 4 GHz, and l = ±3 at 4.8 GHz). Both the simulation and measurement results demonstrate that OAM beams can be generated effectively by the DASA. In addition, a conical cavity is used to increase the gain of the proposed DASA for more than 5 dBi in comparison to the traditional cylindrical cavity. Furthermore, the qualities of the generated OAM modes by the proposed DASA have been evaluated at different operating frequencies of 3 GHz, 4 GHz, and 4.8 GHz, respectively. The OAM modes purities of l = −1, −2, −3, 1, 2, and 3 are predominate with the proportion of about 81%, 70%, 74%, 78%, 77%, and 75%, respectively. Our results demonstrate that the proposed DASA has great potentials in OAM multiplexing communication systems.

Conventional vortex beams carrying orbital angular momentum (OAM) suffer from the limitation of beam divergence in wireless communications applications. This article proposes novel 3-dimensional (3-D) printed discrete dielectric lenses (DDLs) for generation of nondiffractive OAM beams operating at 300 GHz. By virtue of its arbitrary aperture phase control capability, a terahertz (THz) DDL combining the functionalities of three conventional bulky refractive hyperbolic, spiral phase plane, and aixcon lenses is proposed to generate nondiffractive Bessel vortex beam carrying OAM. An aperture field analysis method is also developed to evaluate the radiation performance of the DDL antennas. Furthermore, to cover the OAM signal in an intended longitudinal region, two DDL synthesis methods are explored to generate extended higher order Bessel beams carrying OAM. The first approach is based on geometric optics, while the second uses the alternating projection method (APM) to optimize the aperture phase distribution of the DDL. Two THz DDLs are conveniently fabricated by 3-D printing technology. Measured results demonstrate that THz nondiffractive OAM beams can be successfully generated by the designed DDLs. The generated THz OAM beam with attractive nondiffractive characteristic may open new opportunities for next-generation ultra-high-speed wireless communications.

Programmable metasurfaces show great application potential in many fields, so studying their radar cross-section reduction (RCSR) characteristics is very important. Metasurfaces based on polarization conversion and artificial magnetic conductors are widely used for RCSR, but they cannot scan beams. Programmable metasurfaces can dynamically steer beams in-band and reduce RCS by changing the phase of electromagnetic waves. But to meet practical needs, they must be stealthy both in-band and out-of-band. This paper presents a low-profile self-stealth programmable metasurface. Self-stealth describes the capability of the metasurface to achieve in-band and out-of-band RCSR through its intrinsic design, without requiring additional structures such as radomes or absorbing materials. The design principle is to achieve out-of-band RCS reduction without increasing the profile height or adding extra radio frequency components. The meta-atom has a positive-intrinsic-negative (PIN) diode to control the in-band ( f 0 ) x -polarization phase. Switching the PIN diode states gives 1-bit phase modulation. The in-band y -polarization uses a bridge design. Changing the size can get 1-bit phase, and the x - and y -polarizations can be adjusted separately. Also, the top layer has 4 cross-shaped dumbbells and 4 branch structures for out-of-band high ( fh 1 ) and low ( fl 1 ) frequencies. The middle layer has four 45° rotated cross-shaped dumbbells and 4 branch structures for out-of-band high ( fh 2 ) and low ( fl 2 ) frequencies. So, the meta-atom can modulate phase across 5 frequency bands ( fl 2 < fl 1 < f 0 < fh 2 < fh 1 ). The profile height is 0.065λ of the in-band center frequency, which is more conducive to conformal design. A 12 × 12 prototype was made. Simulation and measurement show that the metasurface reduces RCS in 5 bands and its in-band radiation can be used in communication transmission mode, which is good for programmable metasurface technology development.

In this paper, an array antenna for generating multi-mode orbital angular momentum (OAM) vortex waves and having electrically controlled mode reconfigurable function is proposed. The proposed antenna is based on a reconfigurable feed network (RFN) consisting of multiple PIN diodes as reconfigurable switches, a direct current (dc) control board and a 2 × 4 radial uniform circular array. By controlling the coding sequence of the corresponding PIN diode dc bias voltage on the RFN using a programmable microcontroller, the OAM modes generated by the proposed antenna can be dynamically reconfigured between l = 0, ±1, and ±2. Moreover, the OAM beams can be generated in a wide frequency band of 5.5-6.1 GHz and 5.65-6.1GHz for l = ± 1, ±2 modes and l = 0 mode, respectively. The prototype of the proposed antenna is simulated and fabricated to validate the proposed design. Both far-field and near-field experiments were performed to verify the feasibility of the proposed design. The results of the numerical simulation and measurement have good agreement with each other.

Programmable metasurfaces (PMs) are consisted of reconfigurable digital elements, and electromagnetic properties of the PMs can be manipulated by configuring digital states of these elements. This paper proposes to synthesize multiple beams, sum and difference beams based on a PM. Theoretical calculations validate the functions of the presented PM.

Orbital angular momentum (OAM) beams allow for increased channel capacity in free-space optical communication. Conventionally, these OAM beams are multiplexed together at a transmitter and then propagated through the atmosphere to a receiver where, due to their orthogonality properties, they are demultiplexed. We propose a technique to demultiplex these OAM-carrying beams by capturing an image of the unique multiplexing intensity pattern and training a convolutional neural network (CNN) as a classifier. This CNN-based demultiplexing method allows for simplicity of operation as alignment is unnecessary, orthogonality constraints are loosened, and costly optical hardware is not required. We test our CNN-based technique against a traditional demultiplexing method, conjugate mode sorting, with various OAM mode sets and levels of simulated atmospheric turbulence in a laboratory setting. Furthermore, we examine our CNN-based technique with respect to added sensor noise, number of photon detections, number of pixels, unknown levels of turbulence, and training set size. Results show that the CNN-based demultiplexing method is able to demultiplex combinatorially multiplexed OAM modes from a fixed set with >99% accuracy for high levels of turbulence-well exceeding the conjugate mode demultiplexing method. We also show that this new method is robust to added sensor noise, number of photon detections, number of pixels, unknown levels of turbulence, and training set size.

Orbital angular momentum (OAM) light, combined with the nonlinear process to expand the frequency range, has drawn increasing research interest in recent years. Here, we implement the first, to the best of our knowledge, experimental fourth-harmonic generation of OAM light with two cascaded quasi-phase-matching crystals. A Laguerre-Gaussian beam was transmitted through a duplet crystals system and frequency-doubled twice by two separate second-harmonic generation processes, which transduced the frequency of the OAM beam from telecom band to visible band and then to ultraviolet (UV) band. The topological charge of the OAM beam was increased substantially in the cascaded frequency conversion processes. In this experiment, we verify the OAM conservation by utilizing a specially designed interferometer, and the results correspond well with the numerical simulation. This work provides an effective method for the generation of UV OAM beams with high topological charges.

Artificial intelligence methods for the phase control of laser arrays have been extensively developed in the recent years. To tailor high-power and fast switchable orbital angular momentum (OAM) beams by the coherent combination of laser arrays, complex phase control difficulties arise, and the introduction of deep-learning (DL) methods to learn the mapping from the intensity information to the relative phases of array elements offers a promising solution. In this work, we theoretically propose a DL-based phase control scheme that can customize OAM beams with desirable topological charges from laser array systems, which relies on the acquisition of the optical field information in the view of angular domain. When the system in closed loops, the optical field and phase errors information of laser array are extracted and decoupled in the angular domain perspective by using an OAM demultiplexer. The processed optical field of the coherently combined beam serves the DL-based phase control servo to realize the efficient phase stabilization, thus ensuring the controllable customization of OAM beams. This work could provide a useful reference on the intelligent control of laser array systems for structured light beams customization.