High-Efficiency Wireless Power Transfer System for Capsule Endoscope

The power transfer efficiency of magnetic-resonance coupled wireless power transfer (WPT) systems is sensitive to the alignment of coils. In this paper, a novel multi-coil WPT system is proposed to enhance power transfer efficiency. It can overcome the misalignment problem and maintain high power transfer efficiency. The proposed coil loop structure can provide a strong magnetic resonance coupling between the Tx and Rx coils. There are four induvial resonators applied in the system and it demonstrates that at least a pair of coupled resonators in several misaligned conditions could realize high power transfer efficiency over a misaligned distance. The experimental results show that the proposed multi-loop WPT system can achieve 90.2% peak efficiency when the coils are well aligned. Mean-while, this WPT system maintains over 70% efficiency over a misalignment distance from 0 to 55 mm, which is about 66% of the length of the Rx board. The proposed WPT system could be used either in implant devices for biomedical healthcare and treatment or for electric vehicles charging systems.

Magnetic resonance-based wireless power transfer system offers a promising solution to overcome power limitations typically encountered by capsule endoscopy. Despite of much attention in this area, aspects such as power stability and power transfer efficiency remain suboptimal and therefore investigation for further improvement is still required. This paper presents a method to improve power stability as well as power transfer efficiency for wireless capsule endoscopy. A new power transmission coil capable of producing uniform magnetic field is proposed to improve power stability through uniform field that at the same time minimizes the unnecessary peak electromagnetic exposure. To improve power transfer efficiency, a mixed resonance scheme is employed. Our experimental results show improvement over existing methods where the proposed system attained power stability of 94.62% and power transfer efficiency of 4.9% under worst position of the receiving coil. Furthermore, the proposed transmitting coil provides additional advantage, where it minimized the unnecessary peak electromagnetic exposure by 26% as compared to the conventional Helmholtz coil-based system. We believe the proposed system will open new direction for future wireless capsule endoscopy and can also be useful in other industrial applications.

In this brief, a high-efficiency wireless power transfer (WPT) system for electric vehicle charging application is studied and implemented. Series–series resonant topology with RF feedback design is adopted as the WPT dc–dc stage due to the advantages of circuit simplicity, easy analysis, and control. A 500-W laboratory prototype is built and tested to verify the feasibility of the proposed design. According to the experimental results, high wall-to-battery efficiency and unity power factor can be achieved over an air gap of 15 cm and maximum sliding distance of 10 cm under various power conditions and universal input voltage from 90VAC to 264VAC.

A highly efficient wireless power transfer (WPT) system is required in many applications to replace the conventional wired system. The high temperature superconducting (HTS) wires are examined in a WPT system to increase the power-transfer efficiency (PTE) as compared with the conventional copper/Litz conductor. The HTS conductors are naturally can produce higher amount of magnetic field with high induced voltage to the receiving coil. Moreover, the WPT systems are prone to misalignment, which can cause sudden variation in the induced voltage and lead to rapid damage of the resonant capacitors connected in the circuit. Hence, the protection or elimination of resonant capacitor is required to increase the longevity of WPT system, but both the adoptions will operate the system in nonresonance mode. The absence of resonance phenomena in the WPT system will drastically reduce the PTE and correspondingly the future commercialization. This paper proposes an open bifilar spiral coils based self-resonant WPT method without using resonant capacitors at both the sides. The mathematical modeling and circuit simulation of the proposed system is performed by designing the transmitter coil using HTS wire and the receiver with copper coil. The three-dimensional modeling and finite element simulation of the proposed system is performed to analyze the current density at different coupling distances between the coil. Furthermore, the experimental results show the PTE of 49.8% under critical coupling with the resonant frequency of 25 kHz.

The optimization, manufacturing, and performance characterization of a miniaturized 3D receiver (RX)-based wireless power transfer (WPT) system fed by a multi-transmitter (multi-TX) array is presented in this study for applications in capsule endoscopy (CE). The 200 mm outer diameter, 35 μm thick printed spiral TX coils of 2.8 g weight, is manufactured on a flexible substrate to enable bendability and portability of the transmitters by the patients. The 8.9 mm diameter—4.8 mm long, miniaturized 3D RX—includes a 4 mm diameter ferrite road to increase power transfer efficiency (PTE) and is dimensionally compatible for insertion into current endoscopic capsules. The multi-TX is activated using a custom-made high-efficiency dual class-E power amplifier operated in subnominal condition. A resulting link and system PTE of 1% and 0.7%, respectively, inside a phantom tissue is demonstrated for the proposed 3D WPT system. The specific absorption rate (SAR) is simulated using the HFSSTM software (15.0) at 0.66 W/kg at 1 MHz operation frequency, which is below the IEEE guidelines for tissue safety. The maximum variation in temperature was also measured as 1.9 °C for the typical duration of the capsule’s travel in the gastrointestinal tract to demonstrate the patients’ tissues safety.

The wireless power transfer (WPT) system based on parity-time (PT) symmetry has the advantages of robustness, stable, and efficient power transmission. However, the region of PT symmetry is limited, which cannot satisfy some practical requirements. Multiple transmitting coils have been shown to improve the misalignment tolerance of WPT systems. Towards this end, a parity-time-symmetric-based WPT (PT-based WPT) system with double-transmitting coil is presented in this article. First, an approximate equivalent circuit model of this PT-based WPT system was developed. Second, compared with the conventional single transmitting coil PT-based WPT system, the proposed system expands the PT symmetry region and provides higher output power and transmission efficiency. Furthermore, the mutual inductance between two transmitting coils can be designed to meet the requirements of different scenarios, which improves the freedom of system design. Finally, a 30 W prototype is designed to evaluate the proposed WPT system. Experimental results show that the critical coupling coefficient is reduced by about 12.5% at <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">k</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">12</sub> = 0.51, which implies a longer transmission distance. Moreover, the maximum output voltage fluctuation in the strongly coupled region is only 3.5%, while the transfer efficiency is approximately constant, which implies stable and efficient power transfer.

In previous researches, an operator-based sliding mode control design to achieve high power transfer efficiency of a wireless power transfer (WPT) system via magnetic resonance coupling were shown. However, it is difficult to reduce the steady-state error by using SMC-based tracking controller. In this paper, an operator-based integral sliding mode control method is adopted to reduce the steady-state error in the WPT system. Moreover, high power efficiency should be achieved in the WPT system by using an impedance matching control. The effectiveness of the proposed method is verified by simulation results.

A Wireless Power Transfer (WPT) system, known for its contactless power delivery, is extensively used for power supply in spacecraft applications. Achieving efficient and stable power transfer necessitates the integration of DC/DC converters on both the primary and secondary sides of WPT systems for power conversion and control. Traditional efficiency optimization methods primarily focus on impedance matching within the wireless power resonance network, often neglecting the overall efficiency optimization of multi-stage DC-DC and WPT systems. This oversight results in suboptimal overall system efficiency despite optimal efficiency in the wireless transmission segment. Additionally, the time-varying nature of mutual inductance and load parameters during power transmission in WPT systems presents challenges for maximum efficiency tracking and power control. This paper introduces a multi-level coordinated control efficiency optimization method for WPT systems utilizing the particle swarm optimization (PSO) algorithm. This method takes into account the transmission losses across all power conversion units within the WPT system, establishing a mathematical model for the joint optimization of overall system transmission efficiency and power. The PSO algorithm is then employed to solve this optimization model using estimated mutual inductance and load values. By adjusting the DC/DC converters on both sides, the method ensures optimal overall system efficiency and consistent power transmission. Experimental results indicate that under varying load and mutual inductance conditions, a Series–Series (SS) compensated WPT system using this method achieves a 200 W power output with maximum efficiency tracking, a power output error of 0.63%, and an average transmission efficiency of 86.2%. This demonstrates superior power transmission stability and higher efficiency compared to traditional impedance matching methods.

It is well known that the power transfer efficiency (PTE) of a two-coil wireless power transfer (WPT) system is maximized at critical coupling under fixed system parameters. However, the two-coil WPT system is critical-coupled with a relatively short distance between the coils. To overcome the problem, a multicoil WPT system has been studied. In this paper, we review the impedance characteristics of the critical-coupled two-coil WPT system and reveal that the conventional three-coil WPT system cannot have the same impedance characteristics as critical coupling. Based on the impedance matching conditions with critical coupling of the two-coil WPT system, we propose a design method of a three-coil WPT system in which the free resonant frequencies of all resonators are changed. The proposed design method is successfully implemented at the operating frequency of 6.78 MHz. The experimental results are in good agreement with the simulated PTEs and show that by changing the free resonant frequencies, a higher PTE can be effectively achieved in comparison to the conventional two-coil and thee-coil WPT systems.

Simultaneous power distribution to multiple loads using a single source in the wireless power transfer (WPT) system is a challenging issue due to cross-coupling between the load coils, which reduces the power transfer efficiency. In a resonant WPT system, when two or more coils operated under over coupled condition, the original operating resonant frequency gets bifurcated, and thereby reduction in the power transfer efficiency. Different techniques are investigated in the literature to mitigate the frequency bifurcation phenomena in the resonant WPT system. However, the utilization of frequency bifurcation approach for the simultaneous power transfer to multiple loads is not addressed. This paper proposes a simultaneous power transfer approach using frequency bifurcation for the multiple load system designed with different operating frequency. Mathematical, simulation, and experimental studies performed for dual, triple, and four coil WPT systems with multiple loads. In addition, an automatic power flow control method is implemented to estimate the load current from the source, which helps to select a new set of load coils to be charged. The experimental results confirm the proposed power transfer, helps to attain higher power transfer efficiency of 39.34%, 49.31%, 68.22% and cross interference of -31.2 dBV, -36.2 dBV, -41.2 dBV for dual, triple, and four coil WPT system, respectively.

Achieving high stable Power Transfer Efficiency (PTE) in Wireless Power Transfer (WPT) systems remains challenging due to the nonlinear, multimodal nature of the optimization space. Conventional algorithms such as Genetic Algorithms (GA), Differential Evolution (DE), and Simulated Annealing (SA) often face premature convergence, sensitivity to parameter settings, and inconsistent performance across runs. To overcome these issues, this study introduces the Evolutionary-Swarm Hybrid Algorithm (ESHA), which integrates DE for directional exploration, GA crossover for population diversity, SA for adaptive convergence, and Lévy Flights for stochastic global search. ESHA was implemented on a WPT system with a fixed 20 cm transmission distance and compared with GA, DE, and SA using three performance indicators: PTE, convergence speed, and computational efficiency. Results show that ESHA achieved a maximum PTE of 97.18%, surpassing GA (96.81%), DE (96.65%), and SA (96.19%), while maintaining zero variance across independent runs. It converged in an average of 31.2 iterations, slightly faster than GA (33.15) and SA (32.1), and comparable to DE (31.3). Execution time was 0.4738 s, close to GA (0.4654 s) and only marginally higher than DE (0.4262 s) and SA (0.4329 s). Statistical validation confirmed significant improvements in PTE (p &lt; 0.05).

We found the optimal conditions for an efficient wireless power transfer system (WPTS).In addition, we found that a class‐D power amplifier (PA) has an advantage as a source when the input resistance changes with the position of the receiving antenna. Finally, the proposed WPTS was verified through the experimental results. © 2012 Wiley Periodicals, Inc. Microwave Opt Technol Lett 54:, 2012; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.27062

The use of resonant magneto-inductive links is an efficient technique to transfer power over midranges in the field of wireless power transfer (WPT). Power transfer efficiency (PTE) and power delivered to the load (PDL) are two important indicators of power transmission for a WPT system. A predetermined amount of PDL need be generated at maximum PTE for practical application in a WPT system; thus, the authors focus on maximising PTE and a predetermined amount of PDL for transfer in this study. First, load-matching conditions are presented for maximum PTE transfer though circuit theory-based analyses. Then, a new tuning method is proposed to transfer a predetermined amount of PDL which can be controlled by source-matching distance at maximum PTE. The relations between the loss of a load-matching resonator and the PTE (or PDL) of a correspondingly unmatched system are derived though analyses as well. Finally, the calculated results of the design examples are verified through electromagnetic simulations and experimental measurements.

The next-generation retinal prostheses feature high image resolution and chronic implantation. These features demand the delivery of power as high as 100 mW to be wireless and efficient. A common solution is the 2-coil inductive power link, used by current retinal prostheses. This power link tends to include a larger-size extraocular receiver coil coupled to the external transmitter coil, and the receiver coil is connected to the intraocular electrodes through a trans-sclera trans-choroid cable. In the long-term implantation of the device, the cable may cause hypotony (low intraocular pressure) and infection. However, when a 2-coil system is constructed from a small-size intraocular receiver coil, the efficiency drops drastically which may induce over heat dissipation and electromagnetic field exposure. Our previous 2-coil system achieved only 7% power transfer. This paper presents a fully intraocular and highly efficient wireless power transfer system, by introducing another inductive coupling link to bypass the trans-sclera trans-choroid cable. With the specific equivalent load of our customized 512-electrode stimulator, the current 3-coil inductive link was measured to have the overall power transfer efficiency around 36%, with 1-inch separation in saline. The high efficiency will favorably reduce the heat dissipation and electromagnetic field exposure to surrounding human tissues. The effect of the eyeball rotation on the power transfer efficiency was investigated as well. The efficiency can still maintain 14.7% with left and right deflection of 30 degree during normal use. The surgical procedure for the coils' implantation into the porcine eye was also demonstrated.

Many researches have been carried out by previous researchers to get better performance of a wireless power transfer (WPT) system. This research uses a partitioned shielding made of metallic material to protect WPT system from electromagnetic interference (EMI). Also, a shielding material is connected to ground, so that it can reduce occurrence of stray/parasitic capacitance between electrodes of electronic components. Both the electromagnetic interference and the stray/parasitic capacitance can deteriorate performance of WPT system. In this research, the WPT system works at voltage 14.7V, frequency 56,298 Hz, distance coil to coil is 0 till 5 cm. The efficiency of WPT system is achieved until 14.9 % (without shielding) and until 17.9% (with partitioned shielding).