High-productivity Programming and Optimization Framework for Stream Processing on FPGA

The dissemination of multi-core architectures and the later irruption of massively parallel devices, led to a revolution in High-Performance Computing (HPC) platforms in the last decades. As a result, Field-Programmable Gate Arrays (FPGAs) are re-emerging as a versatile and more energy-efficient alternative to other platforms. Traditional FPGA design implies using low-level Hardware Description Languages (HDL) such as VHDL or Verilog, which follow an entirely different programming model than standard software languages, and their use requires specialized knowledge of the underlying hardware. In the last years, manufacturers started to make big efforts to provide High-Level Synthesis (HLS) tools, in order to allow a grater adoption of FPGAs in the HPC community.Our work studies the use of multi-core hardware and different FPGAs to address Numerical Linear Algebra (NLA) kernels such as the general matrix multiplication GEMM and the sparse matrix-vector multiplication SpMV. Specifically, we compare the behavior of fine-tuned kernels in a multi-core CPU processor and HLS implementations on FPGAs. We perform the experimental evaluation of our implementations on a low-end and a cutting-edge FPGA platform, in terms of runtime and energy consumption, and compare the results against the Intel MKL library in CPU.

Multi-Party Computation (MPC) is a technique enabling data from several sources to be used in a secure computation revealing only the result while protecting the original data, facilitating shared utilization of data sets gathered by different entities. The presence of Field Programmable Gate Array (FPGA) hardware in datacenters can provide accelerated computing as well as low latency, high bandwidth communication that bolsters the performance of MPC and lowers the barrier to using MPC for many applications. In this work, we propose a Secret Sharing FPGA design based on the protocol described by Araki et al. We compare our hardware design to the original authors' software implementations of Secret Sharing and to work accelerating MPC protocols based on Garbled Circuits with FPGAs. Our conclusion is that Secret Sharing in the datacenter is competitive and when implemented on FPGA hardware was able to use at least 10× fewer computer resources than the original work using CPUs.

Building the machines that advance scientific knowledge is one of the most significant challenges of our time. So-called Big Science instruments are unique; the expertise required to build them is multidisciplinary, and few countries can build and maintain them. Since resources and budgets are not unlimited, these require efficient solutions. Big Science machines take a decade to plan, a decade to build, and at least a decade to operate. One such machine is the largest fusion reactor project, ITER, which promises to be the next step in fusion research and has a big challenge in system integration. To mitigate the integration effort, ITER has invested in standardization, both in software and hardware, introducing standard instrumentation software named Nominal Device Support (NDSv3); Micro Telecommunication Computing Architecture (MTCA) as the long-term hardware standard choice, and EPICS as a general-purpose distributed control system. These control systems are essential in the management of the facility. They provide functions such as communication protocols, process management, monitoring, alarms, and human-machine interfaces. But also, more advanced access to databases or data acquisition systems. The latter is typically managed by a Field Programmable Gate Array (FPGA), of which facilities can easily have thousands of these FPGAs managing millions of signals within the control system environment. Nevertheless, these FPGA data acquisition (DAQ) systems continue to be labor-intensive. Standardized, modular, and open-source frameworks have been proposed to solve this problem, however, the FPGA programming expertise requirement remained. This thesis proposes a complete technology stack that considers these DAQ systems from the control system to the hardware. It provides a methodology using the Open Computing Language (OpenCL) to reduce the FPGA programming effort. The FPGA devices are programmed using C/C++-like environments, which are much simpler than traditional Hardware Description Languages (HDLs). The software, named IRIO-OpenCL, is written in C++ following ITER's NDSv3 model, which abstracts and generalizes the development of software device drivers and simplifies the interface to EPICS. IRIO-OpenCL is specifically designed to simplify the integration of intelligent instrumentation systems, allowing the integration of algorithms into the FPGA without modifying large parts of the supporting library. The MTCA standard was chosen to maintain modularity. The chassis backplane connects to the devices via Ethernet and PCIe, enabling standard communications. The Advanced Mezzanine Card is the typical MTCA FPGA-based DAQ carrier board. It connects the FPGA to the chassis backplane and typically provides FPGA Mezzanine Connectors (FMCs) for plugging in analog-to-digital (ADC) carrier boards. An ADC connected via the FMC interface samples the analog signals passed to the OpenCL processing kernels. Using OpenCL, the FPGA kernels communicate with the host machine in a standardized way. To demonstrate the applicability of this methodology, reference problems were selected from the literature and implemented, both with traditional and deep learning (DL) solutions. The methodology elaborates on connecting the OpenCL kernels for any use case, and the results show examples of kernel sets. The neutron flux measurement problem is solved at 1GS/s in real time using pulse counting and Campbell techniques, using 40% of the target Arria10 FPGA. The DL application example is based on a neutron/gamma discrimination neural network (NN) that achieves a classification rate of up to 1.3 MEvents/s using less than 25% of the target resource. RESUMEN Construir máquinas que avancen el conocimiento científico es uno de los desafíos más significativos de nuestro tiempo. Los instrumentos de la llamada Big Science son únicos; las competencias requeridas para su construcción son multidisciplinares, y pocos países pueden construirlos y mantenerlos. Dado que los recursos y presupuestos no son ilimitados, estos requieren soluciones eficientes. Las máquinas de Gran Ciencia tardan una década en planificarse, una década en construirse y al menos una década en operarse. Una de estas máquinas es el proyecto del reactor de fusión más grande, ITER, que promete ser el siguiente paso en la investigación de fusión y presenta un gran desafío en la integración de sistemas. Para mitigar el esfuerzo de integración, ITER ha invertido en estandarización, tanto en software como en hardware, introduciendo un software de instrumentación estándar llamado Nominal Device Support v3 (NDSv3); Micro Telecommunication Computing Architecture (MTCA) como la elección estándar de hardware a largo plazo, y EPICS como un sistema de control distribuido de propósito general. Estos sistemas de control son esenciales en la gestión de la instalación ya que proporcionan funciones como protocolos de comunicación, gestión de procesos, monitorización, alarmas e interfaces de usuario, además de acceso avanzado a bases de datos o sistemas de adquisición de datos. Este último es típicamente gestionado por un Field Programmable Gate Array (FPGA), de los cuales las instalaciones pueden tener fácilmente miles de unidades gestionando millones de señales dentro del entorno del sistema de control. Estos sistemas de adquisición de datos (DAQ) con FPGA siguen requiriendo programación experta y laboriosa. Se han propuesto marcos estandarizados, modulares y de código abierto para resolver este problema, sin embargo, la necesidad de experiencia en programación FPGA no se ha podido eludir. Esta tesis propone una pila de tecnologías que considera estos sistemas DAQ desde el sistema de control hasta el hardware. Proporciona una metodología utilizando el Open Computing Language (OpenCL) para reducir el esfuerzo de programación FPGA. Los dispositivos FPGA se programan utilizando entornos similares a C/C++, que son mucho más simples que los Lenguajes de Descripción de Hardware (HDL) tradicionales. El software, llamado IRIO-OpenCL, está escrito en C++ siguiendo el modelo de NDSv3 de ITER, que abstrae y generaliza el desarrollo de controladores de dispositivos de software y simplifica la interfaz con EPICS. IRIO-OpenCL está específicamente diseñado para simplificar la integración de sistemas de instrumentación inteligentes, permitiendo la integración de algoritmos en el FPGA sin modificar grandes partes de la biblioteca de soporte. El estándar MTCA fue elegido para mantener la modularidad. El backplane del chasis se conecta a los dispositivos a través de Ethernet y PCIe, habilitando comunicaciones estándar. La Advanced Mezzanine Card es la placa portadora DAQ FPGA típica de MTCA, que conecta el FPGA al backplane del chasis y típicamente proporciona FPGA Mezzanine Connectors (FMC) para conectar placas con conversores analógico-digitales (ADC). Un ADC conectado a través de la interfaz FMC muestrea las señales analógicas pasadas a los núcleos de procesamiento OpenCL. Utilizando OpenCL, los núcleos FPGA se comunican con la máquina anfitriona de una manera estandarizada. Para demostrar la aplicabilidad de esta metodología, se seleccionaron e implementaron problemas de referencia de la literatura, tanto con soluciones tradicionales como de Deep Learning (DL). La metodología elabora ejemplos de conexión de núcleos OpenCL para cualquier caso de uso, y los resultados muestran ejemplos de conjuntos de núcleos. El problema de medición del flujo de neutrones se resuelve a 1GS/s en tiempo real utilizando técnicas de conteo de pulsos y Campbell, utilizando el 40% del objetivo FPGA Arria10. El ejemplo de aplicación DL se basa en una red neuronal para la discriminación neutrones/gammas que logra una tasa de clasificación de hasta 1.3 MEventos/s utilizando menos del 25% de la FPGA objetivo. LABURPENA Ezagutza zientifikoa aurreratzen duten makinak eraikitzea gure garaiko erronka garrantzitsuenetako bat da. Big Science deritzonaren makinak bakarrak dira; beharrezko esperientzia diziplina anitzekoa da, eta herrialde gutxik eraiki eta mantendu ditzakete. Baliabideak eta aurrekontuak mugagabeak ez direnez, konponbide eraginkorrak behar dira. Zientzia Handi makinak hamarkada bat behar dute diseinatuak izateko, hamarkada bat eraikitzeko eta gutxienez hamarkada bat jarduteko. Makina horietako bat fusio-erreaktore handienaren proiektua da, ITER, fusio-ikerketan hurrengo urratsa izango dena eta sistemak integratzeko erronka handia aurkezten duena. Integrazio-ahalegina arintzeko, ITERek estandarizazioan inbertitu du, bai softwarean bai - eta EPICS helburu orokorreko kontrol-sistema banatua. Kontrol-sistema horiek funtsezkoak dira instalazioa kudeatzeko. Komunikazio-protokoloak, prozesuen kudeaketa, monitorizazioa, alarmak eta pertsona-makina interfazeak bezalako funtzioak ematen dituzte, datubaseetarako edo datuak eskuratzeko sistemetarako sarbide aurreratua izateaz gain. Azken hori "Field Programmable Gate Array" (FPGA) batek kudeatzen du, milaka FPGA konektatuz makina bakoitzean eta kontrol-sistemaz milioika seinale kudeatuz. FPGA duten datuak eskuratzeko sistemek (DAQ) programazio aditua eta neketsua eskatzen jarraitzen dute. Problema hori ebazteko marko estandarizatuak, modularrak eta kode irekikoak proposatu dira, hala ere, FPGA hardware programazio espezializatuaren beharra ezin izan da ukatu. Tesi honek DAQ sistema hauek kontrol sistematik hardwareraino kontsideratuz teknologia bilduma bat programazio-ahalegina murrizten du. FPGA gailuak C/C++ antzeko inguruneak erabiliz programatzen dira, - OpenCL izenekoa, C++n idatzita dago, ITERren "Nominal Device Support v3" (NDSv3) eredua jarraituz. Honek software-gailuen garapena diseinu abstraktu eta orokorrez EPICSekiko interfazea sinplifikatzen du. IRIOOpenCL berariaz diseinatuta dago instrumentazio-sistema adimendunen integrazioa sinplifikatzeko, eta algoritmoak FPGAn integratzea ahalbidetzen du, software zati handiak aldatu gabe. Modularitateari eusteko, MTCA estandarra aukeratu da. Txasisaren backplanea Ethernet eta PCIe bidez konektatzen da gailuetara, komunikazio estandarrak gaituz. "Advanced Mezzanine Card" MTCAren ohiko DAQ FPGA plaka eramailea da. FPGA txasisaren backplanera konektatzen du eta, normalean, "FPGA Mezzanine Connectors"ak (FMC) ditu plaka bihurgailu analogiko-digitalak (ADC) konektatzeko. ADCak, FMC interfazearen bidez konektatuta, OpenCL prozesatze-nukleoetara igarotako seinale analogikoak bihurtzen ditu. OpenCL erabiliz, FPGA nukleoak ordenagailuarekin modu estandarizatuan komunikatzen dira. Metodologia horren aplikagarritasuna egiaztatzeko, erreferentziazko adibideak literaturatik hautatu eta nukleoen konexio-adibideak egiten ditu, edozein kasutan erabiltzeko, eta emaitzek nukleo multzoen adibideak erakusten dituzte. Neutroi-fluxuaren neurketak 1GS/s-ko ebazten dira real time errendimenduaz, pultsuak eta Campbell zenbatzeko teknikak erabiliz, Arria10 FPGAren % 40 erabiliz. Azkenik, DL aplikazioaren adibidea, neutroi/gamma sailkapena, sare neuronal batean oinarritzen da, eta FPGAren baliabideen % 25 baino gutxiago erabiliz 1.3 MSailkapen/s sailkapen-tasa lortzen du.

The present work investigates Multi – channel Active Vibration Control (AVC) of a composite research wing model and shell structure using modified Filtered × Least Mean Square (F×LMS) algorithm on Field Programmable Gate Arrays (FPGAs). AVC, using Digital Signal Processing (DSP) techniques are cost effective. But FPGAs, consuming small silicon area, have emerged as a dominant technology in embedded applications with potential features like high speed processing and low power consumption. Prominent features like high-speed parallel processing architecture along with hardware reconfigurability facilitates its usage to be wide spread in signal processing applications. An adaptive active vibration control system based on feed forward modified F×LMS algorithm implemented on FPGA hardware is presented here. The results from the Multi channel real time AV C studies are brought out in the paper.

Wireless sensor network (WSN) is a group of interconnected sensor nodes that work wirelessly to capture the information of surroundings. The routing of the network is a challenging task. The routing of WSN is classified as proactive, reactive, and hybrid. Adhoc on-demand distance vector (AODV) routing is an example of reactive routing based on the demand route formations among different nodes in the network. The research article emphasizes the design and simulation of the AODV routing hardware chip using very-high-speed integrated circuit hardware description language (VHDL) programming in Xilinx integrated synthesis environment (ISE) 14.7 software. The performance of the chip is studied based on the field-programmable gate array (FPGA) hardware parameters such as slices, lookup table (LUTs), input/output block (IOB), flip-flops, and memory for the different configurations of the network (N = 10, 20 ….100). The delay and frequency are also estimated on the Virtex-5 FPGA. The performance of the WSN with AODV routing is also analyzed based on the packet delivery ratio, throughput, delay, and control overhead. The simulation test cases verified the 8-bit, 64-bit, and 128-bit data communication within the nodes.

Hardware-in-the-Loop (HWIL) simulation is becoming increasingly important for cost-effective testing of imaging infrared systems. DSTO is developing real-time scene generation and image processing capabilities within its HWIL simulation programs, based on the application of COTS desktop PCs equipped with Graphics Processing Unit (GPU) cards, and including limited use of Field Programmable Gate Arrays (FPGAs). GPUs and FPGAs are high-performance parallel computing machines but are fundamentally different types of hardware. To determine which hardware type should be used to implement a real-time solution of a given application, a methodology is required to expose the concurrency within the problem and to structure the problem in a way that can be mapped to the hardware types. In this paper we use parallel programming patterns to compare the architectures of recent generation GPUs and FPGAs. We demonstrate the decomposition of a parallel application and its implementation on GPU and FPGA hardware and present preliminary results.

The soft computing algorithms are being nowadays used for various multi input multi output complicated non linear control applications. This paper presented the development and implementation of back propagation of multilayer perceptron architecture developed in FPGA using VHDL. The usage of the FPGA (Field Programmable Gate Array) for neural network implementation provides flexibility in programmable systems. For the neural network based instrument prototype in real time application. The conventional specific VLSI neural chip design suffers the limitation in time and cost. With low precision artificial neural network design, FPGA have higher speed and smaller size for real time application than the VLSI design. The challenges are finding an architecture that minimizes the hardware cost, maximizing the performance, accuracy. The goal of this work is to realize the hardware implementation of neural network using FPGA. Digital system architecture is presented using Very High Speed Integrated Circuits Hardware Description Language (VHDL)and is implemented in FPGA chip. MATLAB ANN programming and tools are used for training the ANN. The trained weights are stored in different RAM, and is implemented in FPGA. The design was tested on a FPGA demo board. Keywords- Backpropagation, field programmable gate array (FPGA) hardware implementation, multilayer perceptron, pressure sensor, Xilinx FPGA.

The demand for low-power devices has significantly increased across various applications, highlighting the crucial role of VLSI technology due to its unique capabilities. Traditional data acquisition systems often utilize embedded and ASIC devices, but these devices typically fail to meet the low-power requirements of modern applications. As an alternative, Field Programmable Gate Array (FPGA)-based solutions have emerged as effective candidates for data acquisition systems. This paper presents the implementation of a data acquisition system (DAQ) on a Basys 3 FPGA board utilizing both MicroBlaze and Zynq processors. Temperature sensors, ultrasonic sensors, and OLED peripherals are interfaced and executed on FPGA hardware. The Xilinx Vivado software serves as the design tool to integrate hardware components and processors, employing Verilog as the hardware description language. Performance evaluation confirms that FPGA devices effectively handle DAQ applications at a clock frequency of <tex xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">$\mathbf{1 0 0 ~ M H z}$</tex>.

Median filtering is an important approach in digital image processing for noise elimination. An improved median filtering algorithm (IMFA) is proposed which can be implemented with only 17 comparisons and 6 clocks delay for 3×3 median filtering mathematical model based on field programmable gate array (FPGA). The algorithm benefits from the parallel processing and pipelining structure of FPGA hardware. At first, the characteristics, basic operational principle and computing process of the IMFA are presented. And then the algorithm using modular technique and top-down design flow methodology with Verilog HDL are programed. At last, some simulation verifications for the algorithm by ModelSim and experimental verification on FPGA hardware platform are carried out. The IMFA can get a large number of data throughput and more quickly processing speed and less hardware resources than similar filtering algorithms.

This paper presents an approach of model-based design for implementing a digital communication system on a field programmable gate array (FPGA) for a software defined radio (SDR). SDR is a popular prototyping platform for wireless communication systems due to its flexibility and utility. A traditional SDR system performs nearly all computations and signal processing tasks on the host computer, and then sends the waveform to the RF front end. For complex algorithms or high data rate, the host computer becomes the processing bottleneck and FPGA is often employed as a hardware accelerator. This paper demonstrates the procedure of using model-based design for SDR targeted on FPGA hardware. A complete digital communication system, including a transmitter with convolutional encoder and a receiver with Viterbi decoder, is implemented on an FPGA-based SDR platform and validated by over-the-air demonstration. Synchronization algorithms, such as carrier frequency offset, phase offset, and time recovery, are also optimized for hardware efficiency.

Field Programmable Gate Arrays (FPGAs) have been indispensable components of embedded systems and datacenter infrastructures. However, energy efficiency of FPGAs has become a hard barrier preventing their expansion to more application contexts, due to two physical limitations: (1) The massive usage of routing multiplexers causes delay and power overheads as compared to ASICs. To reduce their power consumption, FPGAs have to operate at low supply voltage but sacrifice performance because the transistors drive degrade when working voltage decreases. (2) Using volatile memory technology forces FPGAs to lose configurations when powered off and to be reconfigured at each power Resistive Random Access Memories (RRAMs) have strong potentials in overcoming the physical limitations of conventional FPGAs. First of all, RRAMs grant FPGAs non-volatility, enabling FPGAs to be Normally powered off, Instantly powered on. Second, by combining functionality of memory and pass-gate logic in one unique device, RRAMs can greatly reduce area and delay of routing elements. Third, when RRAMs are embedded into datpaths, the performance of circuits can be independent from their working voltage, beyond the limitations of CMOS circuits. However, researches and development of RRAM-based FPGAs are in their infancy. Most of area and performance predictions were achieved without solid circuit-level simulations and sophisticated Computer Aided Design (CAD) tools, causing the predicted improvements to be less convincing. In this thesis,we present high-performance and low-power RRAM-based FPGAs fromtransistorlevel circuit designs to architecture-level optimizations and CAD tools, using theoretical analysis, industrial electrical simulators and novel CAD tools. We believe that this is the first systematic study in the field, covering: From a circuit design perspective, we propose efficient RRAM-based programming circuits and routing multiplexers through both theoretical analysis and electrical simulations. The proposed 4T(ransitor)1R(RAM) programming structure demonstrates significant improvements in programming current, when compared to most popular 2T1R programming structure. 4T1R-based routingmultiplexer designs are proposed by considering various physical design parasitics, such as intrinsic capacitance of RRAMs and wells doping organization. The proposed 4T1R-based multiplexers outperformbest CMOS implementations significantly in area, delay and power at both nominal and near-Vt regime. From a CAD perspective, we develop a generic FPGA architecture exploration tool, FPGASPICE, modeling a full FPGA fabric with SPICE and Verilog netlists. FPGA-SPICE provides different levels of testbenches and techniques to split large SPICE netlists, in order to obtain better trade-off between simulation time and accuracy. FPGA-SPICE can capture area and power characteristics of SRAM-based and RRAM-based FPGAs more accurately than the currently best analyticalmodels. From an architecture perspective, we propose architecture-level optimizations for RRAMbased FPGAs and quantify their minimumrequirements for RRAM devices. Compared to the best SRAM-based FPGAs, an optimized RRAM-based FPGA architecture brings significant reduction in area, delay and power respectively. In particular, RRAM-based FPGAs operating in the near-Vt regime demonstrate a 5x power improvement without delay overhead as compared to optimized SRAM-based FPGA operating at nominal working voltage.

Model-Based Iterative Reconstruction (MBIR) algorithms iteratively use expensive computational operators of forward and backward projections. The irregular memory access pattern of these operators makes them a memory-bound application. Their computation time must be reduced to meet clinical routine constraints. This paper proposes a hardware accelerator architecture based on Field Programmable Gate Arrays (FPGAs) through high-level language, as an alternative to GPU architecture. This acceleration is based on an offline memory access analysis to address the main bottleneck of the algorithm and maximize the data reuse rate. The offline analysis allows for the tuning of the architecture parameters so that they converge to an optimal solution. Then, the Berkeley Roofline model guides our optimization steps by iteratively analyzing the design performance. Our design flow significantly improved the algorithm's computational intensity and overcame the memory bottleneck. Thus, our architecture takes advantage of the FPGA local memory to achieve significant memory bandwidth and efficiently harness the pipeline without stalling the computation. Furthermore, we present the scaling-up strategy from mid-range FPGA to high-end FPGA and any concerns of portability. We used two Intel FPGA devices to implement the algorithm, and then we compared the results with our GPU implementation in terms of speedup and energy efficiency. Our experimental results show that our design has achieved better computational throughput than the works on FPGA architectures reported in the literature.

Reconfigurable computing provides a paradigm to create intelligent systems different from the classic software computing approach. Instead of using a processor with an instruction set, a full stack of middleware, and an application program running on top, the field-programmable gate arrays (FPGAs) integrate a cell set that can be configured in different ways. A few vendors have dominated this market with their proprietary tools, hardware devices, and boards, resulting in fragmented ecosystems with few standards and little interoperation. However, a new and complete toolchain for FPGAs with its associated open tools has recently emerged from the open-source community. Robotics is an expanding application field that may definitely benefit from this revolution, as fast speed and low power consumption are usual requirements. This paper hypothesizes that basic reactive robot behaviors may be easily designed following the reconfigurable computing approach and the state-of-the-art open FPGA toolchain. They provide new abstractions such as circuit blocks and wires for building intelligent robots. Visual programming and block libraries make such development painless and reliable. As experimental validation, two reactive behaviors have been created in a real robot involving common sensors, actuators, and in-between logic. They have been also implemented using classic software programming for comparison purposes. Results are discussed and show that the development of reactive robot behaviors using reconfigurable computing and open tools is feasible, also achieving a high degree of simplicity and reusability, and benefiting from FPGAs’ low power consumption and time-critical responsiveness.

Current work on automatic task partitioning and scheduling for reconfigurable computing (RC) systems strictly addresses the field programmable gate array (FPGA) hardware, and does not take advantage of the synergy between the microprocessor and the FPGA. Efforts on partitioning between the microprocessor and the FPGA are often times a manual and laborious effort as a formal methodology for automatic hardware-software partitioning for RC systems has not yet been established. Related fields such as heterogeneous computing (HC) and embedded computing (EC) have an extensive body of work for scheduling for heterogeneous processors. In this work, we adapt HC scheduling algorithms for RC systems, and show how simply adapting the algorithms alone is not sufficient to take advantage of the reconfigurable hardware. In many cases, the HC heuristics algorithms do not generate efficient schedules necessary to take advantage of the synergy between the microprocessor and the FPGA. We introduce new heuristic algorithms based on HC scheduling algorithms and show that they provide up to an order of magnitude improvement in execution time.

In recent years, much High Performance Computing (HPC) researchers attract to utilize Field Programmable Gate Arrays (FPGAs) for HPC applications. We can use FPGAs for communication as well as computation thanks to FPGA's I/O capabilities. HPC scientists cannot utilize FPGAs for their applications because of the difficulty of the FPGA development, however High Level Synthesis (HLS) allows them to use with appropriate costs. In this study, we propose a Communication Integrated Reconfigurable CompUting System (CIRCUS) to enable us to utilize high-speed interconnection of FPGAS from OpenCL. CIRCUS makes a fused single pipeline combining the computation and the communication, which hides the communication latency by completely overlapping them. In this paper, we present the detail of the implementation and the evaluation result using two benchmarks: pingpong benchmark and allreduce benchmark.