Integrated ANN–GA for estimating the minimum value for machining performance

This paper focuses on the Genetic Algorithm learning paradigm applied to train the ANNs for balancing the cart-pole balancing system. The studied system is a classic control problem namely “cart-pole” problem. We will apply the unconventional techniques Artificial Neural Network, Genetic Algorithm and Fuzzy Logic to a classic control problem "cart-pole”. In this paper we have tried to train the Artificial Neural Network (ANN) with using Genetic Algorithms (program is written in MATLAB) which is compared with the output obtained using the Artificial Neural Network Toolbox provided in MATLAB. In proposed approach we have used both ANNs and Genetic Algorithm to get more optimal solution. Here we applied the approach for the Fuzzy logic technique to design a Fuzzy Logic Controllers (FLC) using ANNs and Genetic Algorithm (GA). The Fuzzy rules which are needed to control the problem will be framed with the combination of Artificial Neural Networks and Genetic Algorithm. It has been found that such a searching technique converges intelligently and much faster than conventional learning means. Performance of the presented neural network training using the genetic algorihtms is much better and providing more accurate results.

Cladding is the most economical process used on the surface of low carbon structural steel to improve the corrosion resistance. The corrosion resistant property is based on the amount of ferrite present in the clad layer. Generally, the ferrite content present in the layer is expressed in terms of ferrite number (FN). The optimum range of ferrite number plays an instrumental role to bring adequate surface properties like chloride stress corrosion cracking resistance, pitting and crevice corrosion resistance and mechanical properties. For achieving maximum economy and enhanced life, duplex stainless steel (E2209T1-4/1) is deposited on the surface of low carbon structural steel of IS: 2062. The problem faced in the weld cladding towards achieving the required amount of ferrite number is the selection of an optimum combination of input process parameters (welding current, welding speed, contact tip to specimen distance and gun angle). This paper mainly concentrates on estimating FN and analysis of input process parameters on FN of heat treated duplex stainless steel cladding. To predict FN, mathematical equations was developed based on four factor five level central composite rotatable design with full replication using regression methods. In this paper, artificial neural network (ANN) and genetic algorithm (GA) techniques were integrated and labeled as ANN-GA to identify the optimum process parameters in FCAW to get maximum FN. From the results, the integrated ANN-GA (I OR II) is capable of giving maximum FN at optimum process parameters compared to that of experimental, regression and ANN modeling

Spam detection is one of the major problems which considered by many researchers by different developed strategies. Artificial Neural Network (ANN) is one of many others being proposed. However designing an ANN is a difficult task as it requires setting of ANN structure and tuning of some complex parameters. In this study, ANN was hybridized with Genetic algorithm (GA) in order to optimize the performance of ANN for spam detection. GA was used to determine some ANN parameters and suggest optimum weights to efficiently enhance the ANN learning. Experimental results show that the hybrid ANN and GA has superior performance when compared to conventional ANN.

Artificial neural network and regression coupled genetic algorithm to optimize parameters for enhanced xylitol production by Debaryomyces nepalensis in bioreactor

Temperature is a predominant environmental factor affecting grass germination and distribution. Various thermal-germination models for prediction of grass seed germination have been reported, in which the relationship between temperature and germination were defined with kernel functions, such as quadratic or quintic function. However, their prediction accuracies warrant further improvements. The purpose of this study is to evaluate the relative prediction accuracies of genetic algorithm (GA) models, which are automatically parameterized with observed germination data. The seeds of five P. pratensis (Kentucky bluegrass, KB) cultivars were germinated under 36 day/night temperature regimes ranging from 5/5 to 40/40°C with 5°C increments. Results showed that optimal germination percentages of all five tested KB cultivars were observed under a fluctuating temperature regime of 20/25°C. Meanwhile, the constant temperature regimes (e.g., 5/5, 10/10, 15/15°C, etc.) suppressed the germination of all five cultivars. Furthermore, the back propagation artificial neural network (BP-ANN) algorithm was integrated to optimize temperature-germination response models from these observed germination data. It was found that integrations of GA-BP-ANN (back propagation aided genetic algorithm artificial neural network) significantly reduced the Root Mean Square Error (RMSE) values from 0.21~0.23 to 0.02~0.09. In an effort to provide a more reliable prediction of optimum sowing time for the tested KB cultivars in various regions in the country, the optimized GA-BP-ANN models were applied to map spatial and temporal germination percentages of blue grass cultivars in China. Our results demonstrate that the GA-BP-ANN model is a convenient and reliable option for constructing thermal-germination response models since it automates model parameterization and has excellent prediction accuracy.

Malaria is a disease that caused many adverse effects on humans. Various attempts have been done to find new anti-malarial agents due to the resistance problem of the existing drug. Fusidic acid is known as one of a compound that is promising to be used as an anti-malaria agent. However, this compound should be derived to obtain a new fusidic acid derivative that has better activity. The exploration of the compound in conventional style has a shortcoming in the term of time and cost. Therefore, an alternative method is required to accelerate the design. In this study, we applied a quantitative structure-activity relationship (QSAR) to produce a predictive model. The produced model can be used to predict the activity of the compound as an anti-malaria agent. The development of the model was performed by using genetic algorithm (GA) for feature selection and artificial neural network (ANN) for model development. We developed five models by utilizing a different number of the descriptor in each model. The validation process was performed by evaluating several validation parameters, such as accuracy. According to the results, we found that the model 3, which is comprised of seven descriptors, produce a better result with the accuracies of internal and external data set are 0.96 and 0.92, respectively.

An inverse design method is proposed to achieve the pre-set control objectives of the aircraft cabin environment. The method combines the artificial neural network and the genetic algorithm, and the training and testing data of the artificial neural network is obtained by computational fluid dynamics analysis. Both of the thermal comfort and energy consumption are considered in the inverse design. The artificial neural network is used to identify the relationship between the thermal comfort and the air supply parameters (inlet velocity magnitude and angle, inlet air temperature). The genetic algorithm coupled with the well-trained artificial neural network is used to design the aircraft cabin environment. Numerical results show that the Bayesian regularization algorithm is proved to have better generalization capability than the other training algorithms for the artificial neural network. The increase of training data quantity improves the generalization capability of the artificial neural network, while it spends more simulation time. A computational fluid dynamics database with 60 datasets is shown to be suitable to the present inverse design, and the testing error of the artificial neural network is below 8.2%. Several groups of optimal air supply parameters are found with different trade-offs between the thermal comfort and energy consumption. The best solution of thermal comfort, i.e., the percentage of zone with |PMV| >0.5 in all cabin control domains, is less than 7.8%.

Detecting the different blends of diesel and biodiesel fuels using electronic nose machine coupled ANN and RSM methods

Simultaneous spectrophotometric quantitative analysis of elbasvir and grazoprevir using assisted chemometric models

This paper presents a novel approach to solve the hydro plant dispatch problem based on the artificial neural network (ANN) and genetic algorithm (GA). In this work, the difficult water balance constraints are embedded and satisfied throughout the proposed encoding and decoding algorithms. The ANN is used as a pre-dispatch tool to generate raw hydro output for each hour temporarily ignoring time-dependent constraints. Then, the proposed decoding algorithm decodes the raw schedule of each plant into a feasible one. Finally, a GA is used to find the optimal schedule. The proposed approach is applied to an actual utility system of four hydro plants and 22 thermal units with great success. Results show that the new approach obtains a more highly optimal solution than the conventional dynamic programming method.

Student performance is related to complex and correlated factors. The implementation of a new advancement of technologies in educational displacement has unlimited potentials. One of these advances is the use of analytics and data mining to predict student academic accomplishment and performance. Given the existing literature, machine learning (ML) approaches such as Artificial Neural Networks (ANNs) can continuously be improved. This work examines and surveys the current literature regarding the ANN methods used in predicting students’ academic performance. This study also attempts to capture a pattern of the most used ANN techniques and algorithms. Of note, the articles reviewed mainly focused on higher education. The results indicated that ANN is always used in combination with data analysis and data mining methodologies, allowing studies to assess the effectiveness of their findings in evaluating academic achievement. No pattern was detected regarding selecting the input variables as they are mainly based on the context of the study and the availability of data. Moreover, the very limited tangible findings referred to the use of techniques in the actual context and target objective of improving student outcomes, performance, and achievement. An important recommendation of this work is to overcome the identified gap related to the only theoretical and limited application of the ANN in a real-life situation to help achieve the educational goals.

The Indo-Australian Plate, the Eurasian Plate, and the Pacific Plate all converge where Indonesia is situated. As a result, Indonesia is a nation where earthquakes occur frequently. Some researchers have studied machine learning algorithms for categorizing earthquake vibrations. In this experiment, earthquake vibrations are categorized using the Artificial Neural Network method. We need appropriate datasets to obtain the maximum accuracy from the artificial neural network technique. The findings of this experiment show that feature extraction is required for the datasets to be trained to obtain a high accuracy value. The mean, median, maximum, minimum, skew, and kurtosis values are the feature that are extracted. In addition to employing feature extraction, it is crucial to modify the algorithm model. The experimental setup that uses “sigmoid” activation on the input layer, the three hidden layers, and the output layer yields the best accuracy when all feature are extracted, with training to test ratio of 90% to 10%. This is demonstrated by the exceptional training accuracy and testing accuracy values, which are 99.85 percent for training accuracy and 99.12 percent for validation accuracy. The mean value yields the highest accuracy result compared to employing just one feature extraction. Only 90.97 and 90.37 percent of training and validation accuracy are obtained when the mean is used alone for feature extraction.

Official statistics on monthly export values have a publicity lag between the current period and the published publication. None of the previous researchers estimated the value of exports for the monthly period. This circumstance is due to limitations in obtaining supporting data that can predict the criteria for the current export value of goods. AIS data is one type of big data that can provide solutions in producing the latest indicators to forecast export values. Statistical Methods and Conventional Machine Learning are implemented as forecasting methods. Seasonal ARIMA and Artificial Neural Network (ANN) methods are both used in research to forecast the value of Indonesia’s exports. However, ANN has a weakness that requires high computational costs to obtain optimal parameters. Genetic Algorithm (GA) is effective in increasing ANN accuracy. Based on these backgrounds, this paper aims to develop and select an AIS indicator to predict the monthly export value in Indonesia and optimize ANN performance by combining the ANN algorithm with the genetic algorithm (GA-ANN). The research successfully established five indicators that can be used as predictors in the forecasting model. According to the model evaluation results, the genetic algorithm has succeeded in improving the performance of the ANN model as indicated by the resulting RMSE GA-ANN value, which is smaller than the RMSE of the ANN model.

This paper presents the fusion of artificial intelligence (AI) learning algorithms that are genetic algorithms (GA) and conjugate gradient (CG) methods. Both methods are used to find the optimum weights for the hidden and output layers of feedforward artificial neural network (ANN) model. Each algorithm is presented in separate module and we proposed three different types of Dynamic Connection Strategies (DyConS) for combining both algorithms to improve the recognition performance of spoken Malay speech recognition. Two different GA techniques are used in this research: a mutated GA technique is proposed and compared with the standard GA technique. One hundred experiments with 5000 words are conducted using the proposed DyConS. Owing to previous facts, GA combined with ANN proved to attain certain advantages with sufficient recognition performance. Thus, from the results, it was observed that the performance of mutated GA algorithm when combined with CG is better than standard GA and CG models. Integrating the GA with feed-forward network improved mean square error (MSE) performance and with good connection strategy by this two stage training scheme, the recognition rate is increased up to 99%.

Though the high-speed railways are seen as a sustainable form of transportation, the fact that the rail wear in high-speed railways negatively affects the running safety and riding comfort, as well as the maintenance of railways, has drawn a wide range of concerns among researchers and scholars. In order to reduce the rail wear and achieve the goal of sustainable transportation, this paper proposes an ingenious optimization program of rail profiles based on the artificial neural network (ANN) and genetic algorithm (GA) coupled method. The candidate solutions of the nonlinear GA programming model are regarded as the inputs of the trained ANN model. Meanwhile, the outputs of the trained ANN model serve as the objective functions of the GA model. The computational results show that the optimized rail profile not only has superior performances in terms of the wheel/rail wear and contact conditions, but also maintains good dynamic performances. Therefore, this study can provide the theoretical and practical basis for the design and the preventive grinding of rails in the high-speed railways. Also, the ANN-GA coupled model can be extended and further employed on the optimization of other rail profiles.