Interference-Aware Gossiping Scheduling in Uncoordinated Duty-Cycled Multi-hop Wireless Networks

This paper addresses the Quality of Service (QoS) degradation problem of wireless relay node failures in multihop Worldwide interoperable Microwave Access (WiMAX) and Long Term Evolution (LTE) networks. In general, node protection in a communication network increases the reliability of the traffic flow from source to destination. For wireless networks, implementing the traditional 1+1 protection scheme increases the capital cost, as resources cannot be fully utilized. On the other hand, the design and implementation of the 1:N protection scheme in wireless networks for greater value of N (> 2) is very difficult, due to wireless network coverage and the physical layer design. To overcome the above drawbacks, a technique based on network coding is proposed for node protection in multihop wireless networks. In multihop wireless networks, few research efforts are concentrated on node protection schemes using network coding. Moreover, to best of our knowledge, no reports have been published on measuring the QoS performance for node protection in 4G wireless networks using network coding. In this paper, we first describe the node protection scheme using XOR network coding for multihop 4G wireless networks. Then, we measure the QoS performance, such as packet delivery ratio (PDR), latency and jitter, for different scenarios. The scenarios include a failure of a single relay node and failures of two relay nodes with and without our protection scheme and user's mobility. The simulation results show that the QoS performance with protection against a single relay node failure and failures of two relay nodes are very close to that of no failure scenario, while the network reliability increases due to the protection mechanism. Also, we report a decoding problem in multihop wireless networks using XOR network coding.

This paper studies joint scheduling and network coding in wireless multicast networks with independent sources. Designing a network coding solution for wireless networks involves scheduling interference-free transmissions and optimizing a performance measure for the predetermined scheduling sets, followed by constructing network codes for the specific solution. In such a design process, the results of prior steps need to provide enough information to the subsequent steps. In this paper, we formulate a linear optimization problem whose results can be used to design a coding solution. We build our work on previous works and present statistics that show the importance of incorporating unequal timeshares in designing network codes. In particular, our statistics show a throughput improvement of about 35% in maximum flow problems and energy savings between 13% and 30%, depending on the network size, in minimum energy problems. We also present the requirements of code construction algorithms for wireless networks that capture the broadcast property of these networks and can design proper codes when timeshares are unequal. In particular, the adaptation of a centralized network coding scheme for wireless networks is discussed. Overall, the work reported here provides a three-step solution to derive network codes that optimize a performance criterion of interest while also solving the scheduling problem in multihop wireless networks.

The increasing use of multi-hop wireless networks and the growing demand of bandwidth-intensive multimedia applications are the driving force to explore innovative techniques that can enhance the capacity of multi-hop wireless networks. The commonly used omni-directional antennas limit the spatial reusability of the wireless channel and hence reduce the available capacity of wireless networks. On the contrary, bandforming antennas, that enable directional transmissions and receptions, can overcome the aforementioned limitation. With the recent advances in signed processing and antenna technologies, smart beamforming antennas have become feasible in compact sizes and suitable prices and hence pertinent to multi-hop wireless networks. However, lack of appropriate control over the antenna beamforming may deteriorate the overall performance even below the level achieved by omni-directional antennas. Moreover, beamforming antennas introduce unprecedented challenges including deafness and directional hidden terminal problems. Hence, it is important to design efficient mechanisms for both Medium Access Control (MAC) and routing to deal with these challenges that hinder the full exploitation of spatial reusability offered by smart beamforming antennas. In this dissertation, we develop an analytical framework for modeling directional contention-based MAC protocols, which is, up to our knowledge, the first model to include deafness in the analysis. We show that deafness can severely limit the network capacity. Based on the insights gained from our analysis of the limitations of the existing solutions, we propose a novel opportunistic directional MAC protocol for multi-hop wireless networks with beamforming antennas. The proposed MAC protocol employs a new backoff mechanism that aims at minimizing the unnecessary idle waiting time, which is a key factor in leveraging the spatial reuse. Through extensive simulations, we demonstrate that the proposed MAC protocol enhances the performance in terms of throughput, delay, packet delivery ratio and fairness. We have also addressed the question about the theoretical capacity gain achieved by beamforming antennas. We derive a generic interference model that can accommodate any antenna radiation pattern and show that the capacity gain is significant even when realistic antenna radiation patterns are used. Since smart beamforming antennas can significantly spare the network resources, they can be utilized to provide Quality of Service (QoS) guarantees. We study the bandwidth-guaranteed routing problem in contention-based multi-hop wireless networks with beamforming antennas. We first present an analysis for the wireless links interdependencies in a contention-based environment in the presence of beamforming, which helps in our formulation of the QoS routing problem as a mixed-integer non-linear optimization problem. We then propose a routing and admission control algorithm for its solution. Our simulation results demonstrate the accuracy of our analysis and the ability of our proposed algorithm to find bandwidth-guaranteed routes. In summary, the analysis and design approaches, adopted in this dissertation, enhance the throughput of multi-hop wireless networks by grasping the transmission opportunities offered by smart beamforming antennas while dealing with the beamforming-related challenges at the MAC and network layers, which otherwise limit the spatial reusability of the wireless channel.

Fractional Link scheduling is one of the most fundamental problems in wireless networks. The prevailing approach for shortest fractional link scheduling is based on a reduction to the maximum-weighted independent set problem, which itself may not admit efficient approximation algorithms. In addition, except for the wireless networks under the protocol interference model, none of the existing scheduling algorithms can produce a link schedule with explicit upper bounds on its length in terms of the link demands. As the result, the polynomial approximate capacity regions in these networks remain blank. This paper develops a purely combinatorial paradigm for fractional link scheduling in wireless networks. In addition to the superior efficiency, it is able to provide explicit upper bounds on the lengths of the produced link schedule. By exploiting these upper bounds, polynomial approximate capacity regions are derived. The effectiveness of this new paradigm is demonstrated by its applications in wireless networks under the physical interference model and wireless MIMO networks under the protocol interference model.

This paper tries to reconcile the tension between physical model and protocol model that have been used to characterize interference relationship in a multi-hop wireless network. The physical model (a.k.a. SINR model) is widely considered as a reference model for physical layer behavior but its application in multi-hop wireless networks is limited by its complexity. On the other hand, the protocol model (a.k.a. unified disk graph model) is simple but there have been doubts on its validity. This paper explores the following fundamental question: How to correctly use the protocol interference model? We show that in general, solutions obtained under the protocol model may be infeasible in practice and thus, results based on blind use of protocol model can be misleading. We propose a novel concept called and present a method of using protocol model with reality check for wireless networks. Subsequently, we show that by appropriate setting of the interference range in the protocol model, it is possible to narrow the solution gap between the two models. Our simulation results confirm that this gap is indeed small (or even negligible). Thus, our methodology of joint reality check and interference range setting retains the protocol model as a viable approach to analyze multi-hop wireless networks.

The efficient scheduling of transmission links in a wireless network with a certain optimization objective and subject to the interference and network flow constraints plays a central role in wireless networking research. As an alternative to traditional mathematical analysis, data-driven learning methods have shown promise in solving difficult problems by extracting knowledge from experiences and inspired applications of machine learning in wireless networking. In this paper, we focus on tackling the fundamental scheduling issue in multi-hop wireless networks with machine learning, facing the great challenges of the involvement of non-differentiable operations and the consideration of variable network topologies. To address these issues, we propose a reinforcement learning-based method to solve a class of network flow problems under the protocol interference model. Learning from experience, the proposed approach develops a strategy to sequentially select optimum subsets of links to transmit simultaneously to maximize the system throughput without causing interference. The model structure is designed in a way that incorporates network topological information to allow a flexible number of network nodes, and allows non-differentiable decision operation to pass informative gradient information. Experiments with synthetic and real-world deployment data demonstrate that the proposed algorithm achieves close-to-optimum performance at a significantly reduced time cost.

Achieving optimal transmission throughput in data networks is known as a fundamental but hard problem. The situation is exacerbated in multi-hop wireless networks due to the interference among local wireless transmissions. In this paper, we propose a general modeling and solution framework for the throughput optimization problem in wireless networks. In our framework, data routing, wireless medium contention and network coding are jointly considered to achieve the optimal network performance. The primal-dual solution method in the framework represents a cross-layer optimization approach. It decomposes the original problem into data routing sub-problems at the network layer, and power allocation sub-problems at the physical layer. Various effective solutions are discussed for each sub-problem, verifying that our framework may handle the throughput optimization problem in an efficient and distributed fashion for a broad range of wireless network scenarios.

Information-theoretic broadcast channels (BCs) and multiple-access channels (MACs) enable a single node to transmit data simultaneously to multiple nodes, and multiple nodes to transmit data simultaneously to a single node, respectively. In this paper, we address the problem of link scheduling in multihop wireless networks containing nodes with BC and MAC capabilities. We first propose an interference model that extends protocol interference models, originally designed for point-to-point channels, to include the possibility of BCs and MACs. Due to the high complexity of optimal link schedulers, we introduce the Multiuser Greedy Maximum Weight algorithm for link scheduling in multihop wireless networks containing BCs and MACs. Given a network graph, we develop new local pooling conditions and show that the performance of our algorithm can be fully characterized using the associated parameter, the multiuser local pooling factor. We provide examples of some network graphs, on which we apply local pooling conditions and derive the multiuser local pooling factor. We prove optimality of our algorithm in tree networks and show that the exploitation of BCs and MACs improve the throughput performance considerably in multihop wireless networks.

Cooperative communication has emerged as a promising technique to improve transmission reliability and spectral efficiency by utilizing virtual antenna arrays formed by multiple nodes in wireless networks. In this paper, we study distributed interference-aware random access strategies based on cooperative link selection scheduling for multi-hop wireless networks. In order to fully exploit the broadcast feature of wireless channels, improve spatial reuse, and achieve diversity gains, the cooperative random access is formulated as a network utility optimization problem with probabilistic model and interference avoidance. In the multi-hop wireless networks, the nodes near the destination node in the current hop that can decode the data packets from the source node are able to serve as candidate relays to take part in the cooperative transmission in the next hop. Simulation results show that our proposed spectrum access strategy significantly improves the system average throughput and spectrum efficiency compared with the existing solutions.

Beaconing is a primitive communication task in which every node locally broadcasts a packet to all of its neighbors within a fixed distance. The problem Minimum Latency Beaconing Schedule (MLBS) seeks a shortest schedule for beaconing subject to the interference constraint. MLBS has been well studied when all the nodes are always awake. However, it is well-known that the networking nodes often switch between the active state and the sleep state to save energy. A node in duty-cycled scenarios may require transmitting multiple times to inform all of its neighbors due to their different active times. Thus, all of the known algorithms for MLBS are not suitable for duty-cycled multihop wireless networks. In this paper, we study MLBS in Duty-Cycled multihop wireless networks (MLBSDC). We first present two constant-approximation algorithms for MLBSDC under the protocol interference model with the approximation bounds independent of the length of a scheduling period. Then, we develop an efficient algorithm for MLBSDC under the physical interference model. To the best of our knowledge, this is the first paper that develops efficient algorithms for MLBSDC under either of these two interference models.

MaxWeight algorithm, a.k.a., back-pressure algorithm, has received much attention as a viable solution for dynamic link scheduling in multi-hop wireless networks. The basic principle of the MaxWeight algorithm is to select a set of interference-free links with the maximum overall link weights in the network, where the link weight is determined by the queue difference between the transmitter and the receiver. While the throughput-optimality of the MaxWeight algorithm is well understood in the literature, the energy consumption induced by the MaxWeight algorithm is less studied, which is of great interest in energy-constrained wireless networks such as wireless sensor networks. In this paper, we propose an energy-conserving scheduling scheme, a.k.a., minimum energy scheduling (MES) algorithm for multi-hop wireless networks with stochastic traffic arrivals and time-varying channel conditions. We show that our algorithm is energy optimal in the sense that the proposed MES algorithm can achieve an energy consumption which is arbitrarily close to the global minimum solution. Moreover, the energy efficiency of the MES algorithm is achieved without losing the throughput- optimality. In other words, the proposed MES algorithm is still throughput optimal whereas the average consumed energy in the network is significantly reduced, as compared to the traditional MaxWeight algorithm. The theoretical results are substantiated via simulations.

MaxWeight algorithm, a.k.a., back-pressure algorithm [1]-[4], has received much attention as a viable solution for dynamic link scheduling in multi-hop wireless networks. The basic principle of the MaxWeight algorithm is to select a set of interference-free links with the maximum overall link weights in the network, where the link weight is determined by the queue difference between the transmitter and the receiver. While the throughput-optimality of the MaxWeight algorithm is well understood in the literature, the energy consumption induced by the MaxWeight algorithm is less studied, which is of great interest in energy-constrained wireless networks such as wireless sensor networks. In this paper, we propose a minimum energy scheduling (MES) algorithm for multi-hop wireless networks with stochastic traffic arrivals and time-varying channel conditions. We show that our algorithm is energy optimal in the sense that the proposed MES algorithm can achieve an energy consumption which is arbitrarily close to the global minimum solution. Moreover, the energy efficiency of the MES algorithm is achieved without losing the throughput-optimality. In other words, the proposed MES algorithm is still throughput optimal whereas the average consumed energy in the network is significantly reduced, as compared to the traditional MaxWeight algorithm. The theoretical results are substantiated via simulations.

Wireless multi-hop local area networks use in general scheduling schemes that assume the network capacity to be known. Indeed in most of the throughput-optimal algorithms the sources are assumed to send at a rate within the capacity region. However, measurements made on real deployments show that the network capacity is usually difficult to characterize and also time-varying. It is therefore important to understand how the network behaves when the sources attempt to transmit at a rate above capacity. Toward this goal, we show 3-phase regime in the effect of the input rate λ on the end-to-end throughput μ of a multi-hop network. First, when λ is smaller than a threshold λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</sub> , μ is an increasing function of λ. Second, when λ is larger than another threshold λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> > λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</sub> , μ is independent of λ. Third, when λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1</sub> <; λ <; λ <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> , μ decreases with λ. To understand this phenomenon, we capture the relation between the end-to-end throughput and the queue stability with a mathematical model that allows us to explain and derive the exact values of the transition points λi. We then validate experimentally our simulation results with measurements on a testbed composed of five wireless routers.

Assigning unique consecutive numerical identifiers (IDs) to the nodes of a multi-hop wireless network is an important problem, as it enables critical functions such as resource distribution (e.g., TDMA time slots) and leader election. If also used as a mean to “shorten” otherwise assigned node IDs node enumeration saves energy and imposes lower complexity. In this paper we present an efficient scheme for enumerating the N nodes of a multi-hop wireless network. Our protocol, called WiEnum for Wireless Enumeration, is distributed and, by means of the sole exchange of packets among neighbors, terminates with each node having a unique ID in the range 1 to N. Through Castalia-based simulations we demonstrate the effectiveness of WiEnum in assigning unique, short IDs by comparing its performance to that of another leading algorithm for ID assignments, termed SIDA. Our results show that, in terms of completion time (i.e., the time it takes till each node gets its unique ID) WiEnum outperforms SIDA, especially in networks with higher number of nodes and density. At the same time, WiEnum keeps energy consumption to levels that are always lower than those of SIDA.

Multi-hop wireless networks have attracted much attention because of their flexibility and deploy ability. However, we have previously shown that communication stability in multi-hop wireless networks is degraded by a congestion propagation problem that occurs among neighbor APs. To prevent congestion propagation and enable stable communication, we proposed QMTR (Queue Management with Transmission Record) as a buffer management scheme. We have shown that this scheme allows sufficiently stable communication in a steady state. In this study, we consider a more realistic environment that includes transient states. Through simulation evaluation, we show that the scheme enables sufficiently stable communication even under a transient state in multi-hop wireless networks.