L2-James Webb Space Telescope operationally friendly environment?

The James Webb Space Telescope (JWST) Optical Simulation Testbed (JOST) is a tabletop workbench to study aspects of wavefront sensing and control for a segmented space telescope, including both commissioning and maintenance activities. JOST is complementary to existing optomechanical testbeds for JWST (e.g. the Ball Aerospace Testbed Telescope, TBT) given its compact scale and flexibility, ease of use, and colocation at the JWST Science & Operations Center. We have developed an optical design that reproduces the physics of JWST’s three-mirror anastigmat using three aspheric lenses; it provides similar image quality as JWST (80% Strehl ratio) over a field equivalent to a NIRCam module, but at HeNe wavelength. A segmented deformable mirror stands in for the segmented primary mirror and allows control of the 18 segments in piston, tip, and tilt, while the secondary can be controlled in tip, tilt and x, y, z position. This will be sufficient to model many commissioning activities, to investigate field dependence and multiple field point sensing & control, to evaluate alternate sensing algorithms, and develop contingency plans. Testbed data will also be usable for cross-checking of the WFS&C Software Subsystem, and for staff training and development during JWST’s five- to ten-year mission.

Vibration isolation and precision pointing control will be essential to the success of future space science missions such as Next Generation Space Telescope (NGST). This research investigated the use of actively controlled piezoelectric stack actuators to reduce the transmission of mechanical disturbances to the optics and to coarsely point the telescope. Initial actuator requirements were based on approximate expected motions on the spacecraft side (due to unbalanced reaction wheel assemblies), the structural dynamic properties of the flexible, deployable truss structure that supports the active optics, and the allowable motions on the telescope side. Piezoelectric actuator design was based on flextensional motion amplification, with sizing details determined using results from finite element analysis. A compressive pre-load was maintained on the fragile piezoceramic stacks via a mechanical interference (center block) fit into the actuator frame. Device performance characteristics, including blocked force, passive stiffness, free displacement, motion amplification factor, natural vibration frequencies, and electromechanical coupling coefficient were determined numerically and experimentally, with good agreement. An initial controlled isolation test of the entire system reduced the transmissibility by more than 80% over the frequency range from 4-20 Hz. Finally, an active isolation system with dual sensor feedback was implemented and shown to successfully reduce telescope motion by a factor of 10 (from 4-40 Hz) and to provide lower-frequency pointing capability. Introduction As space systems continue to grow in complexity and require greater precision, piezoelectric materials will be investigated for an increasing number of actuator applications, including precision pointing and vibration isolation and control. There are several approaches to vibration isolation, which have been successful in the past. Vibration isolation can be achieved through passive or active techniques or a combination of the two. The chosen method of isolation depends primarily on the application and requirements of the system. Precision pointing, on the other hand, is achieved solely by active control systems, which combine the necessary structural and mechanical components with a control design. Pointing systems are primarily limited by the quality of the mechanical system as well as the drive system, which is actuating movement. The structure (holding the pay load) to be controlled can be a rigid body, quasi-static flexible body, or a dynamic flexible body. With the classical arrangements of sensors and actuators in these control systems, only the rigid body configuration is commonly controlled. NGST (Next Generation Space Telescope) is the successor to the Hubble Space Telescope (HST) mission. NGST is a deployable 8-meter diameter truss structure holding the telescope and instruments such as cameras and spectrometers that are required by the scientific goals of the mission. In order to meet the scientific goals or projects such as the Origins of Galaxies studies [Mather, et al] along with independent science projects dealing with current scientific interests, positioning the optics and minimizing vibratory loads are very important. Positioning control for the HST was done as a rigid structure pointed as a unit to a precision of a small fraction of an arcsecond, but NGST is a dynamic flexible structure with sub-micron positioning performance. For NGST, the isolation system is to be used to reduce the ultrafine pointing requirements on the fine pointing system (fast steering mirror and adjusters distributed across the mirror) by as much as 1 2 orders of magnitude. This isolation system is aimed to reduce the estimated 30-nm peak disturbances at the mast to 6-nm or less in a range of 4 4 0 Hz, with most concern on the 15 20 Hz region. By substantially reducing these axial disturbances, the dynamic, wavefront error correction requirements will also be reduced, and the fine pointing system will have less of a burden. In order to achieve these requirements, piezoelectric stack actuators are ideal because they can provide sufficiently high output forces with large bandwidths. Individually, piezoelectric stack displacements are extremely small, on the order of approximately 2000 jiie; therefore, multiple stacks can be used in series to produce the desired output. In addition to this, mechanical amplification devices can be used to increase actuation displacement by reducing the actuation force. Compliant mechanisms, flexurehinged mechanisms and flextensional mechanisms Copyright © 2001 by the American Institute of Aeronautics and Astronautics, Inc. All rights reserved. (c)2001 American Institute of Aeronautics & Astronautics or Published with Permission of Author(s) and/or Author(s)' Sponsoring Organization. are commonly used for motion amplification, depending on the application. The flextensional actuator used in this research is shown in Figure I and consists of four stacks of piezoceramics connected in parallel to a flextensional mechanism that amplifies and converts the output

The James Webb Space Telescope (JWST) is the successor to the Hubble Space Telescope. JWST will be an infrared-optimized telescope, with an approximately 6.5 m diameter primary mirror, that is located at the Sun-Earth L2 Lagrange point. Three of JWST’s four science instruments use Teledyne HgCdTe HAWAII-2RG (H2RG) near infrared detector arrays. During 2010, the JWST Project noticed that a few of its 5 μm cutoff H2RG detectors were degrading during room temperature storage, and NASA chartered a “Detector Degradation Failure Review Board” (DD-FRB) to investigate. The DD-FRB determined that the root cause was a design flaw that allowed indium to interdiffuse with the gold contacts and migrate into the HgCdTe detector layer. Fortunately, Teledyne already had an improved design that eliminated this degradation mechanism. During early 2012, the improved H2RG design was qualified for flight and JWST began making additional H2RGs. In this article, we present the two public DD-FRB “Executive Summaries” that: (1) determined the root cause of the detector degradation and (2) defined tests to determine whether the existing detectors are qualified for flight. We supplement these with a brief introduction to H2RG detector arrays, some recent measurements showing that the performance of the improved design meets JWST requirements, and a discussion of how the JWST Project is using cryogenic storage to retard the degradation rate of the existing flight spare H2RGs.

The James Webb Space Telescope (JWST) is a large, infrared space telescope operating at Lagrange point 2. JWST is a joint effort between NASA, ESA, and CSA and was launched from the Centre Spatial Guyanais (CSG) on an Ariane 5 rocket in December 2021. The Ariane 5 payload faring (PLF), interior and Vehicle Equipment Bay membranes received multiple cleanings, detailed inspections, and verification sampling to achieve necessary cleanliness levels.Investigation of PLF cleanliness began early in the JWST program to test the Fairing Acoustic Protection (FAP) panels. Initial PLF cleaning was performed at RUAG in Switzerland prior to shipment to the launch site in collaboration with NASA and ESA. The cleaning procedure used at RUAG premises was based on heritage of the PLF cleaning procedure for ESA/Herschel-Planck and NASA/Mars2020 missions on an Atlas V launcher. The Ariane 5 fairing was packaged in a clean manner and inspected and cleaned upon arrival to CSG. Silicon wafers and particle fall out (PFO) plates were used to monitor the internal fairing cleanliness prior to encapsulation. Just after encapsulation, PFO plates and calcium fluoride (CaF2) crystals were placed inside the fairing on a specific tool door for monitoring the cleanliness inside the fairing during the ventilation phase. The fairing itself was specially sealed to protect the inner environment with just a small, doored porthole accessible via diving board for final closeout of the purge interface. Fairing cleanliness was achieved and mitigated contamination distribution upon launch.

The James Webb Space Telescope (JWST) is a space-based, infrared observatory designed to study the early stages of galaxy formation in the Universe. The telescope will be launched into an elliptical orbit about the second Lagrange point and passively cooled to 30-50 K to enable astronomical observations from 0.6 to 28 microns. A group from the NASA Goddard Space Flight Center and the Northrop Grumman Space Technology prime contractor team has developed an optical and mechanical layout for the science instruments within the JWST field of view that satisfies the telescope s high-level performance requirements. Four instruments required accommodation within the telescope's field of view: a Near-Infrared Camera (NIRCam) provided by the University of Arizona; a Near-Mared Spectrometer (NIRSpec) provided by the European Space Agency; a Mid-Infrared Instrument (MIRI) provided by the Jet Propulsion Laboratory and a European consortium; and a Fine Guidance Sensor (FGS) with a tunable filter module provided by the Canadian Space Agency. The size and position of each instrument's field of view allocation were developed through an iterative, concurrent engineering process involving the key observatory stakeholders. While some of the system design considerations were those typically encountered during the development of an infrared observatory, others were unique to the deployable and controllable nature of JWST. This paper describes the optical and mechanical issues considered during the field of view layout development, as well as the supporting modeling and analysis activities.

This paper characterizes the actual science performance of the James Webb Space Telescope (JWST), as determined from the six month commissioning period. We summarize the performance of the spacecraft, telescope, science instruments, and ground system, with an emphasis on differences from pre-launch expectations. Commissioning has made clear that JWST is fully capable of achieving the discoveries for which it was built. Moreover, almost across the board, the science performance of JWST is better than expected; in most cases, JWST will go deeper faster than expected. The telescope and instrument suite have demonstrated the sensitivity, stability, image quality, and spectral range that are necessary to transform our understanding of the cosmos through observations spanning from near-earth asteroids to the most distant galaxies.

The James Webb Space Telescope (JWST) is a large, infrared-optimized space telescope consisting of the following elements: (1) Optical telescope element (OTE) (2) Integrated science instrument module (ISIM) (3) Spacecraft (4) Sunshield The Integrated Science Instrument Module (ISIM) consists of the JWST science instruments (NIRCam, MIRI, NIRSpec), a fine guidance sensor (FGS), the ISIM Structure, and thermal and electrical subsystems. JWST's instruments are designed to work primarily in the infrared range of the electromagnetic spectrum, and the instruments and telescope operate at cryogenic temperatures (approximately 35 K for the instruments). The development and validation of a thermal distortion modeling and analysis capability for the JWST ISIM Structure was successfully completed. The modeling and analysis approach was grounded in initial constituent materials testing and benchmarked to test results at the composite bonded joint, subassembly, and fullscale flight hardware levels. Comparison of analysis predictions and test results from this series of incremental cryogenic thermal distortion tests demonstrates that the model validation goals are achieved.

From its orbit around the Earth-Sun second Lagrange point some million miles from Earth, the James Webb Space Telescope (JWST) will be uniquely suited to study early galaxy and star formation with its suite of infrared instruments. To maintain exceptional image quality using its 6.6 meter segmented primary mirror, wavefront sensing and control (WFS&C) is vital to ensure the optical alignment of the telescope throughout the mission. WFS&C design architecture includes using the Near-Infrared Camera (NIRCam) to provide imagery for ground-resident image processing algorithms which determine the optimal alignment of the telescope. There are two distinct mission phases for WFS&C, both of which use algorithms and NIRCam imagery to determine the required segment updates. For the first phase, WFS&C commissioning, the telescope is taken from its initial deployed state with each of the 18 primary mirror segments acting like independent telescopes, to its final phased state with each segment acting in concert as a part of a single mirror. The second phase, Wavefront Monitoring and Maintenance, continues for the rest of the mission. Here the wavefront quality is evaluated, and when needed, the mirror positions are updated to bring it back to an optimal configuration. This paper discusses the concept of operations for the commissioning and on-going maintenance of the telescope alignment using WFS&C.

The James Webb space telescope (JWST) project at the NASA, Goddard Space Flight Center (GSFC) is responsible for the development, launch, flight, and science operations for the telescope. The project is in phase B with its launch scheduled for no earlier than June 2013. The project is a partnership among NASA, the European Space Agency (ESA), and the Canadian Space Agency (CSA). The JWST mission team is fully in place, including major ESA and CSA subcontractors. This paper provides an overview of the planned JWST science, current architecture focusing on the instrumentation, and mission status, including technology developments and risks.

For large space missions maximizing the time spent observing science targets by minimizing overhead increases the scientific return of the mission. On the James Webb Space Telescope (JWST), the baseline mode of resetting the near infrared detectors is a pixel-by-pixel reset. For the Hawaii-2RG detectors this requires 10.5 seconds. Over the life of the mission, 2-3% of the total time is spent performing these resets. In this paper, we investigate using the much faster row-by- row reset mode of the Hawaii-2RG as an alternative. Resets in this mode can be performed in only 40 milliseconds allowing more time for science. We investigate how the changing of the reset modes affects: thermal stability of the detectors, total noise, and observed persistence after bright sources are observed. Overall, any negative side effects seem to be outweighed by the increase in the available exposure time for science during the lifetime of JWST.

The Next Generation Space Telescope (NGST) will be a segmented, deployable, infrared-optimized 6.5m space telescope. Its active primary segments will be aligned, co-phased, and then fine-tuned in order to deliver image quality sufficient for the telescope's intended scientific goals. Wavefront sensing used to drive this tuning will come from the analysis of focussed and defocussed images taken with its near-IR science camera, NIRCAM. There is a pressing need to verify that this will be possible with the near-IR detectors that are still under development for NGST. We create simulated NIRCAM images to test the maintenance phase of this plan. Our simulations incorporate Poisson and electronics read noise, and are designed to be able to include various detector and electronics non-linearities. We present our first such simulation, using known or predicted properties of HAWAII HgCdTe focal plane array detectors. Detector effects characterized by the Independent Detector Testing Laboratory will be included as they become available. Simulating InSb detectors can also be done within this framework in future. We generate Point-Spread Functions (PSF's) for a segmented aperture geometry with various wavefront aberrations, and convolve this with typical galaxy backgrounds and stellar foregrounds. We then simulate up-the-ramp (MULTIACCUM in HST parlance) exposures with cosmic ray hits. We pass these images through the HST NICMOS `CALNICA' calibration task to filter out cosmic ray hits. The final images are to be fed to wavefront sensing software, in order to find the ranges of exposure times, filter bandpass, defocus, and calibration star magnitude required to keep the NGST image within its specifications.

This paper summarizes the findings of the Next Generation Space Telescope (NGST) Detector Requirements Review Panel. This panel was comprised of NGST Integrated Science Instrument Module study representatives, detector specialists, and members of the NGST project science team. It has produced a report that recommends detector performance levels, and has provided rationale for deriving these levels from basic, anticipated NGST science goals and programs. Key parameters such as detector array format, quantum efficiency, and noise are discussed and prioritized.

The Near-Infrared Spectrograph (NIRSpec) is one of four instruments aboard the James Webb Space Telescope (JWST). NIRSpec is developed by ESA with AIRBUS Defence & Space as prime contractor. The calibration of its various observing modes is a fundamental step to achieve the mission science goals and provide users with the best quality data from early on in the mission. Extensive testing of NIRSpec on the ground, aided by a detailed model of the instrument, allow us to derive initial corrections for the foreseeable calibrations. We present a snapshot of the current calibration scheme that will be revisited once JWST is in orbit.

The James Webb Space Telescope (JWST) Integrated Science Instrument Module (ISIM) Structure is a precision optical metering structure for the JWST science instruments. Optomechanical performance requirements place stringent limits on the allowable thermal distortion of the metering structure between ambient and cryogenic operating temperature (~35 K). This paper focuses on thermal distortion testing and successful verification of performance requirements for the flight ISIM Structure. The ISIM Structure Cryoset Test was completed in Spring 2010 at NASA Goddard Space Flight Center in the Space Environment Simulator Chamber. During the test, the ISIM Structure was thermal cycled twice between ambient and cryogenic (~35 K) temperatures. Photogrammetry was used to measure the Structure in the ambient and cryogenic states for each cycle to assess both cooldown thermal distortion and repeatability. This paper will provide details on the post-processing of the metrology datasets completed to compare measurements with performance requirements.

The next generation of space telescopes will be designed to meet increasingly challenging science goals. The operating environment and required precision of these telescopes will make complete verification via ground tests impossible, and will place a greater reliance on numerical simulation. The current state of the art in thermal, mechanical and optical modeling involves three disparate computational models, several analysis codes and tools to transition results between these models. However, the active controls necessary to meet the next generation of requirements for space telescopes will require integrated thermal, structural, optical and controls analysis. To meet these challenges, JPL has developed Cielo, an in-house finite element tool capable of multi-physics simulations using a common finite element model, for thermal, structural and optical aberration analysis. In this paper, we will discuss the use of Cielo for analysis of a coronagraph and an occulter designed to observe Earth-like planets around nearby stars. We will compare thermal and structural results from Cielo with results from commercial off the shelf (COTS) tools to verify the new approach. We will perform variations of key parameters to demonstrate how margins and uncertainties can be quantified using the new approach.