- Research Article
163
- 10.1016/j.coastaleng.2006.02.005
Simulation of wave overtopping by an incompressible SPH model
- May 02, 2006
- Coastal Engineering
- Songdong Shao + 5 more +5
Simulation of wave overtopping by an incompressible SPH model
The design of the coastal structure or offshore structure must take into account the hydrodynamic force of water waves to assure the structure stability. In many cases, offshore structures are supported by a group of cylinders piles. The distance between the cylinders and their layout may affect the force on the cylinder which can be not calculated analytically. This paper discusses the use of numerical model based on Lagrangian particle concept. Software namely DualSPHysics was available for the simulation. The software was developed from Smooth Particle Hydrodynamic model in C++ and CUDA languages employing GPU. This research showed the ability of DualSPHysics to simulate wave force on the single cylinder that was comparable to the analytical solution. The significant deviation was observed when the model was applied to wave force on pile groups due to a number of reasons. The particle size ratio to the gap between the cylinders seems to have a significant effect on the accuracy of the solution. It was also found that the numerical waves dissipate quite significantly after propagating a few wavelength. Such dissipation might be reduced by refining the size of the water particle.
Simulation of wave overtopping by an incompressible SPH model
Simulation of wave overtopping by an incompressible SPH model
Bird Impact Analysis of Wing Leading Edge Structure Based on SPH Method
In this paper, a new bird model which combined the visco-elastic material properties and Smooth Particle Hydrodynamics (SPH) method has been proposed to simulate the bird features in high-speed conditions. A rigid plate impact test was adopted to compare the reaction of SPH and Lagrangian bird model. Compared with the results of Lagrangian bird model, new SPH model was more in line with the experimental data, and has better computational efficiency. The SPH bird model was further used to bird impacting with the wing leading edge by using finite element program LS-DYNA. Two kinds of leading edge structural enhancement programs have been proposed and carried out simulation of bird impact. Basis of calculation, the design parameters of experimental structure was determined and was produced to wait for final testing.
Read more3D multi-resolution SPH modeling of the water entry dynamics of free-fall lifeboats
3D multi-resolution SPH modeling of the water entry dynamics of free-fall lifeboats
Scour From Cyclic Lateral Loading of Piles
Two types of scour can be identified at piles supporting offshore structures:erosion of the sea bottom (sea-bottom scour) at obstructions due to oscillatory waves and unidirectional currents, andthe loss of soil around a pile due to the cyclic deflection of the pile under wave forces. The second type (pile scour) is associated with cohesive soils and is the subject of this study. Observations during onshore testing have revealed that the loss of lateral capacity of a pile in cohesive soils is due principally to the creation of a gap at the pile-soil interface and to the subsequent ejection of water from the gap at the space opens and closes during the cyclic loading. The paper describes the phenomenon of pile scour, presents the details of a laboratory test to investigate the scour potential of various soils, discusses the significant findings of a research study, and indicates the influence of pile scour on the design of laterally loaded piles for offshore structures. INTRODUCTION A 24-in (610 mm) 0.D. pipe pile was driven into overconsolidated clay at a site near Manor, Texas and tested under static- and cyclic-lateral loading (1). The test was conducted in a shallow pit and water a few inches deep was kept in the pit at all times. The following statement is abstracted from the report on the, testing program. "During cyclic loading, considerable scouring action was observed around the pile. The cyclic loading caused a pumping action in the water in the gap between the pile and the soil. This pumping action eroded the soil and widened the gap between the pile and soil; a hole to the side and slightly behind the pile developed during cyclic loading; the hole at the side was approximately 4 in. (100 mm) in diameter and 2 ft (600 mm) deep." A test of a 3 by 3 group of piles, each 10.75 in. (273 mm) in diameter and on a center-to-center spacing of 3 diameters, was conducted at a site on the campus of the University of Houston (2). The surface soils were overconsolidated clays that were jointed and slickensided. The investigators reported that grayish silty clay, existing below a depth of 4 ft (1.2 m), was pumped up to the ground during cyclic loading. The objectives of the study described herein were to present a qualitative description of the mechanism of scour or soil erosion at the interface of pile and clay (pile scour) and to provide a means of identifying clays that are susceptible to such scour. The mechanism of scour at the pile-soil interface is described in general terms, and details are presented of a laboratory test for investigating the scour potential of various soils. In the laboratory tests, soil samples with different characteristics were selected and tested. Studies (4) were made of natural soils from the Sabine, Texas site (5), the Manor, Texas site (1), and from a North Sea site.
Read moreWave forces on offshore structures
The determination of the forces induced by water waves on an offshore structure is one of the central interests in the design of the structure. There is a large variety of offshore structures which can be described as being composed of small tubular members, large gravity platforms, tension-legged platforms, with large vertical, horizontal, diagonal, circular or square cylinders, semi-submersibles and arctic structures. These structures may be fixed and compliant and also may be floating in waves. Whatever the case, the complexity of the interaction of waves with the structures makes the calculation of wave forces more difficult. Furthermore, owing to the inherent nonlinear nature of ocean waves, no suitable nonlinear mathematical theory is available at present to predict the wave forces on an offshore structure, the following three methods are available to calculate wave forces: (a) the Morison equation, (b) Froude-Krylov theory and (c) diffraction theory. The distinction between these methods is described below.
Read moreSPH study of scale effects of perforated caissons
SPH study of scale effects of perforated caissons
Hydrodynamics Analysis Based on Improved VBF SPH Model
To improve the application of Smoothed Particle Hydrodynamics (SPH) method, a new Visual Basic-Fortran (VBF) SPH model with the improvements on efficiency and visualizable interface is presented. The VBF SPH model is based on mixed language programming (MLP) method that not only improved SPH model’s efficiency, but also created the interface functions to control and observe the whole simulation. İts general structrue is to compiling the Fortran computing subroutines into Dynamic Link Library (DLL) files and these files will be called by Visual Basic (VB) programs during the calculation. Besides that an improved link-list algorithm, is described detailedly. This algorithm improves the model’s searching efficiency by reducing the number of searching cells. Two classical problems, Flood flow over Dam and Droplet-Impact, are chosen to analyze the VBF SPH model efficiency and distinguish the improvements’ effect. Both of problems are simulated respectively by VBF SPH model and VB model. According to first simulation VBF SPH model is more than 8 times faster than the VB model. And the second simulation refers that the MLP method increased about 7 times efficiency while the improved link-list algorithm increased more than 1 time.
Read moreAn FEM-SPH coupled model for simulating penetration of armor-piercing bullets into ceramic composite armors and glass composite armors
To improve the ballistic simulation accuracy of ceramic composite armors and glass composite armors (transparent armors) against small-caliber armor piercing bullets, the new FEM (finite element method) -SPH (smooth particle hydrodynamics) coupled model was proposed, which replaced the FEM model and JC (Johnson-Cook) material model of the armor-piercing-bullet core of traditional FEM-SPH coupled model with the SPH model and JH2 (Johnson-Holmquist-ceramics) material model. The results show that the new FEM-SPH coupled model can effectively simulate bullet core fragmentation and reduce FEM-SPH coupled calculation amount. So it can improve the computation accuracy and efficiency. And the FEM element/SPH particle size and armor modeling size of the new FEM-SPH coupled model are optimized.
Read moreNumerical investigations on bionic propulsion problems using the multi-resolution Delta-plus SPH model
Numerical investigations on bionic propulsion problems using the multi-resolution Delta-plus SPH model
Numerical Evaluation of the Lateral Behavior of Vertical and Battered Pile Group Foundations Using 3-D Finite Element Modeling
The design of pile foundations to resist lateral loads is essential in offshore structures and bridge foundations. The lateral behavior of piles has been studied in the past by experimental investigations coupled with analytical and numerical methods. The problem is complex due to the nonlinearities from soil behavior, gap formation, and pile-soil-pile interaction in pile groups (or the group effect). In this work, the finite element (FE) modeling was used to study the lateral behavior of pile groups. The FE method is robust and allows incorporating the necessary aspects for studying the behavior of pile groups. The nonlinear material behavior was incorporated using nonlinear constitutive models. The pile-soil interface was modeled using the zero-thickness surface-surface interaction, which provided the capability for modeling the gap behind the piles, and the transfer of interface normal and frictional stresses. The group interaction was facilitated thru the interaction of stress fields around the piles, and by the continuity of the FE mesh. The lateral behavior of three pile group (PG) configurations (vertical, battered, mixed) with a similar number of piles were evaluated under static and dynamic loading. In the static analysis, the case study of the M19 pier foundation field test was used to verify the FE models. A parametric investigation for the effect of pile spacing and clay soil type was performed. The results showed that the lateral stiffness of the battered and mixed PGs was significantly higher than the vertical PG (+120%, +50%, respectively). The lateral load was found unevenly distributed among the piles in all PGs, and the exterior piles carried 1.5-2% higher load than the interior piles. The influence of the group effect vanished at pile spacings greater than 5D (D is pile width). Also, the influence of pile spacing was more prominent along the load direction. In the dynamic analysis, the PGs behavior was evaluated in barge impact simulations. The results showed that the battered and mixed PGs had similar and large lateral stiffness, which resulted in limited pile cap displacement and large deformation in the barge bow. The weak lateral stiffness of the vertical PG allowed the development of significantly larger impact force and pile cap displacement compared to the battered and mixed PG.
Read moreMetal cutting modelling SPH approach
The purpose of this work is to evaluate the use of the smoothed particle hydrodynamics (SPH) method within the framework of high speed cutting modelling. First, a 2D SPH based model is carried out using the LS-DYNA® software. The developed SPH model proves its ability to account for continuous and shear localised chip formation and also correctly estimates the cutting forces, as illustrated in some orthogonal cutting examples. Then, the SPH model is used in order to improve the general understanding of machining with worn tools. At last, a hybrid milling model allowing the calculation of the 3D cutting forces is presented. The interest of the suggested approach is to be freed from classically needed machining tests: Those are replaced by 2D numerical tests using the SPH model. The developed approach proved its ability to model the 3D cutting forces in ball end milling.
Read moreThe Effect Of Uncertainty In Wave Force Coefficients For Offshore Structures
INTRODUCTION The wave forces on an offshore structure are determined by a wave theory (e.g., Stokes or Stream Function) which relates the water kinematics (velocity and acceleration) to the wave parameters (height and period), and a theory which relates the resulting pressures on the structure to the predicted water kinematics (e.g., Morison Equation or Refraction Theory). Generally, the Morison Equation is used which incorporates two force coefficients-the drag and inertia coefficients. The wave parameters experienced by a structure during a storm are random. Also, inferred values of the force coefficients from field measurements indicate a random scatter from wave to wave due to the random nature of the processes involved and imperfect wave and hydrodynamic theories. Therefore, for offshore structures the prediction of wave forces and ultimately the selection of design criteria involve both the random nature of the wave parameters (e.g., height) and the uncertainty in the force coefficients. Procedures for selecting wave heights for design criteria have received considerable attention and are well established; however, the problem of considering the uncertainty in the force coefficients has received little attention. Currently there is no rational procedure to generally account for coefficient uncertainty except to use arbitrary, and potentially unrealistic, guidelines such as the mean value plus a multiple of the standard deviation. The purpose of this paper is to provide a rational framework for dealing with the uncertainty in force coefficients. This framework is statistical and incorporates into the force statistics the uncertainty of the force coefficients and the random occurrence of the wave parameters. BACKGROUND The wave forces on an offshore structure are generally determined by the Morison equation (Mathematical Equation Available in Full Paper) and QD and Qr are the drag and inertia forces (respectively) per unit length acting normal to a structural element; CD and Cr are the drag and inertia coefficients (i.e., the force coefficients), v and v are the water velocity and acceleration normal to the element, D is the element diameter and P is the mass density of water. As shown in Appendix I, the maximum total horizontal forces on a vertical cylinder during a wave cycle are (Mathematical Equation Available in Full Paper) which are obtained by integrating (1) over the water depth. FD is the total drag force; Fr is the total inertia force; H is the wave height and s is the wave steepness (height/wave length). The assumptions used to derive (2) are deepwater waves and linear wave theory. Similar expressions have been presented in Ref. 1. Except for the properties of the water and cylinder (p,D), (2) depends only on the force coefficients, CD and Cr, and wave height, H, if the steepness is small (exp(2ns)=1) or constant. It is noted that for these conditions the total forces are independent of wave period.
Read moreForecasting landslide mobility using an SPH model and ring shear strength tests: a case study
Abstract. Flow-like landslides, such as flow slides and debris avalanches, have caused serious infrastructure damage and casualties for centuries. Effective numerical simulation incorporating accurate soil mechanical parameters is essential for predicting post-failure landslide mobility. In this study, smoothed particle hydrodynamics (SPH) incorporating soil ring shear test results were used to forecast the long-runout mobility for a landslide on an unstable slope in China. First, a series of ring shear tests under different axial stresses and shear velocities were conducted to evaluate the residual shear strength of slip zones after extensive shear deformation. Based on the ring shear test results, SPH modeling was conducted to predict the post-failure mobility of a previously identified unstable slope. The results indicate that the landslide would cut a fire service road on the slope after 12 s and cover an expressway at the foot of that slope after 36 s. In the model, the landslide would finally stop sliding about 38 m beyond the foot of the slope after 200 s. This study extends the application of the SPH model from disaster simulations to predictive analysis of unstable landslide. In addition, two sets of comparative calculations were carried out which demonstrate the robustness of the SPH method.
Read moreReview of Construction of Marine and Offshore Structures by Ben C. Gerwick Jr.Construction of Marine and Offshore StructuresCRC Press, Taylor & Francis Group$130
This is one of the most definitive references available on marine construction. This comprehensive book covers all major aspects of the construction process for a variety of waterborne structures, including marine, offshore, coastal, riverine, and arctic engineering structures. The late Professor Gerwick has substantially revised the previous edition of his Construction of Marine and Offshore Structures book by extensively augmenting this third edition to include recent developments in these rapidly expanding engineering fields. With the added chapters and improvements, the third edition becomes a necessary reference book for all marine and civil engineers and corporations involved in planning, building, and maintaining structures in water environments. This book is an authoritative guide because it addresses many aspects of the current state of practice in easily understandable style, presenting the most comprehensive treatment of the construction process for marine and offshore structures. The author starts with design factors and planning considerations and describes many issues affecting the building of different types of structures in a marine environment. In addition, the book includes chapters on construction and maintenance of coastal and inland waterway structures and pays special attention to recent advances for ice-resistant structures, dams and locks, and bridge foundations. A number of the latest developments in materials and techniques are also described in this new edition that should be of great interest to engineers in the oil and service industries, as well as marine construction planners, designers, and contractors. To retain the volume’s standing as a complete authoritative resource, the author has incorporated into this edition many changes related to techniques, tools, and materials that have found their way into marine and offshore engineering practice. Topics with expanded coverage include construction equipment, marine operations, steel and concrete offshore platforms, cables and flexible or rigid pipelines and risers, tubes tunnels , walls, piles, rubble-mound breakwaters, precast armor units in coasts, repairs and strengthening existing structures, and removal and salvage. The author also provides new information on novel technologies, methods, materials, liquefaction of loose sediments, scour and erosion, ultra-high-performance concrete, H-piles and high-performance steel, cracking and corrosion, and construction in remote areas. He presents an interesting insight to archaeological concerns and damage from sabotage and terrorism, since these are important elements of the construction process. For marine construction planners, designers, contractors, ocean, coastal, and marine engineers involved in constructing waterborne structures, this book describes effec-
Read moreExtreme Wave-Force Calculation Procedure for 20th Edition of API-RP-2A
The paper decribes the revised guideline design wave force calculation procedure approved for the 20th edition of the API-RP2A WSD and the first edition of the API-RP2A LRFD and contrasts it with the procedures in previous editions of RP2A. It also briefly dicusses the new metocean criteria for the Gulf of Mexico. The revised procedure was developed by the API Task Group on Wave Force Commentary. It embodies research results obtained over the last 25 years. It is a significant revision of the guideline wave force calculation procedures that have been part of the RP2A since the 1976 edition. INTRODUTION The paper decribes the revised guideline design wave force calculation procedure approved for the 20th edition of the API-RP2A WSD1 and the first edition of the API-LRFD2 and contrasts it with the procedure in the 19th edition of RP2A3. it also briefly discuesses the new metocean criteria for the Gulf of Mexico. The intent of the paper is to make personnel involved in structure design and assessment aware of the significant changes in the new editions of RP2A and the bases for these changes. The main reference for this paper is the 20th edition of the RP2A, which has a detailed commentary, with an extensive set of reference, that discusses the basis for each element of the revised wave force procedure. The same information is also contained in the first edition of RP2A LRFD. The revised procedure was developed by the API Task Group on Wave Force Commentary. It embodies research results obtained over the last 25 years. It is a significant revision of the guideline wave force calculation procedures that have been part of RP2A since the 1976 edition. BACKGROUND The task group was formed at the request of API to write a commentary on the existing RP2A procedure. The first task group meeting was held in December 1987 to discuss objectives and scope, and procedures to archieve them. After reviewing the RP2A procedures the task group concluded that a commentary consistent with the existing guideline disign calculation procedures could not be written. A considerable body of new knowlegde on wave forces had been developed since the first guidelines appeared in the 1976 edition of RP2A. Therefore the task group decided to expand the scope by developing new guidelines and a supporting commentary. Before defining the new guidelines, the task group performed a series of wave force comparison studies to (a) ascertain the accurancy of the computer codes in performing wave force calculations for given environmental conditions, force coeffients, and structure geometry; (b) evaluate differences in Gulf of Mexico (GOM) design wave forces that were being used at that time; (c) and evaluate differences in "best" estimates of GOM 100-yr wave forces. Results of these studies showed significant differences in GOM design force levels (up to a factor of two) but better agreement in the "best" estimates of the 100-yr wave forces. And very importantly, the "best" 100-yr wave forces were considerably higher than the values obtained using RP2A. The study, its conclusions, and recommendations were presented to the API Subcommittee on Fixed Systems Criteria In October 1989. Before accepting the higher forces the task group recommended the following (a) set up an API task group to review uncertainties and biases in structural capacity; (b) have the wave force task group complete its work and expand the scope to develop 100-yr hurricane wave, wind, and current criteria for the GOM incorporating the latest hindcasts; and (c) have industry try the wave force recipe to see if it is consistent with experience in the Gulf of Mexico. The Subcommittee supported the recom
Read more