Metaheuristic Algorithm Based Maximum Power Point Tracking Technique Combined With One Cycle Control For Solar Photovoltaic Water Pumping Systems

Renewable energy is an attractive solution for water pumping systems particularly in isolated regions where the utility grid is unavailable. An attempt is made to improve the performance of solar photovoltaic water pumping system (SPVWPS) under partial shading condition. Under this condition, the power versus voltage curve has more than one maximum power point (MPP), which makes the tracking of global MPP not an easy task. Two MPP tracking (MPPT) strategies are proposed and compared for tracking MPP of SPVWPS under shading condition. The first method is based on the classical perturb and observe (P&O) and the other method is based on a Salp Swarm Algorithm (SSA). Based on extensive MATLAB simulation, it is found that the SSA method can provide higher photovoltaic (PV) generated power than the P&O method under shading condition. Consequently, the pump flowrate is increased. But, under normal distribution of solar radiation, both MPPT techniques can extract the maximum power but SSA is considered a time-consuming approach. Moreover, SSA is compared with particle swarm optimization (PSO) and genetic algorithm (GA). The obtained results ensure the superiority of SSA compared with PSO and GA. SSA has high successful rate of reaching true global MPP.

Wind energy systems have become a major commodity in the use of renewable energy resources, but its implementation requires great technical challenges in power extraction. Giligenting Island, Madura, East Java, is a prospective area for wind energy development. An algorithm applied to obtain optimal power from wind power generation. This paper presents a performance evaluation of the methods that can be applied as the MPPT (Maximum Power Point Tracking) algorithms. P&O (Perturbation and Observation), IC (Incremental Conductance), and PSO (Particle Swarm Optimization) are studied and discussed as the MPPT techniques in this research. All three methods are implemented on systems that have the same characteristics, they are compared to the simulation results. At the base wind turbine speed of 12 m/s, the P&O method obtained MPPT power of 295.82 W with settling time at 1.02 s. The IC method obtained MPPT power of 297.08 W with settling time at 1 s. Then, The PSO method achieved an MPPT power of 297.45 W with time settling at 0.88 s. According to the simulation results, the PSO is the algorithm that provided the best performance among all MPPT algorithms studied. Beside good response to wind speed variations, PSO also has a simple structure and easy to implement.

PV irrigation systems have begun to be used intensively today, as energy needs increase. In Partially Shaded Conditions (PSC), the efficiency of the PV system decreases significantly, and traditional Maximum Power Point Tracking (MPPT) algorithms become insufficient. On the other hand, traditional MPPT algorithms require sensors to measure the current and voltage of the PV system. In this study, a sensorless hybrid MPPT algorithm is proposed to reduce system costs and enable operation without the need for PV system data. A simulation study was conducted in the MATLAB/Simulink environment to examine the PV system. The proposed algorithm has been tested under four different PSC scenarios. PV system power, motor speed, and currents were examined under each condition. The high maximum power tracking performance of the proposed algorithm is demonstrated through simulation results. In the steady state, the lowest MPPT efficiency was 95.66%, whereas the highest MPPT efficiency was 99.9%. The MPPT algorithm completed in less than 2 seconds, with the first stage taking 1.3 seconds to reach most of the maximum PV system power. The second stage of the MPPT algorithm was used to achieve maximum power in a narrower area.

This paper reviews the existing models, connection schemes and maximum power point tracking (MPPT) methods of PV arrays. The partial shading causes significant power losses. It is very difficult to maintain uniform irradiance over the entire PV array, especially for rooftop or building-integrated PV systems. The aspects such as connection scheme of PV array, shading pattern and maximum power point tracking (MPPT) techniques, etc., decide the power generated by the PV array. The conventional MPPT methods are only capable of reaching maximum power point (MPP) in identical insolation situations. Hence, conventional MPP tracking becomes inept due to the existence of several peaks in the P-V characteristics. There are different global maximum power point (GMPP) tracking techniques available in the literature that operate in partial shading scenarios. The reconfiguration of the PV array reduces the number of multiple peaks. This reduction in several peaks makes conventional MPP tracking techniques competent even under partial shading conditions with low implementation complexity and higher tracking speed. This paper can assist scientists in choosing a precise objective-based PV module model, connection schemes and MPP tracking methods out of numerous schemes available in the literature.

Solar photovoltaics (PV) has proven itself to be the most dependable source for harvesting solar energy. The output of solar PV system relies upon solar radiation and temperature which vary throughout the day. This causes variations in the maximum power point (MPP) on the solar PV output characteristics curve. Therefore, various Maximum Power Point Tracking (MPPT) techniques are used to track the MPP and extract maximum power out of the PV systems. This paper acquaints a simulation based comprehensive study for comparison of three widely adopted MPPT algorithms: Perturb and Observe (P&O), Particle Swarm Optimization (PSO) and Cuckoo Search (CS) using MATLAB Simulink. These MPPT algorithms are implemented to regulate the duty cycle of a DC-DC Boost converter. The performance of the three algorithms is compared on the basis of their tracking speed, accuracy and tracking efficiency. The CS MPPT algorithm showed the best tracking efficiency among the three under partial shading and fast changing conditions of irradiance.

The power output of a photovoltaic (PV) system is inherently dependent on climatic factors. To maximize the energy harvested from PV arrays, maximum power point tracking (MPPT) algorithms are employed. These algorithms dynamically adjust the operating point of the system to extract the maximum available power. However, under partial shading conditions (PSCs), conventional MPPT algorithms often fail to locate the global maximum power point, leading to suboptimal power extraction. In this study, a robust MPPT technique based on sliding mode control (SMC) is proposed to enhance tracking efficiency and optimize power extraction from PV arrays under PSC. Particle swarm optimization (PSO) is incorporated into the MPPT framework, enabling the dynamic tuning of SMC parameters for improved adaptability and performance. The proposed SMC structure is designed to regulate the duty cycle of a boost converter, ensuring effective power conversion. The system is simulated in Matlab/Simulink for various PSCs. The simulation results demonstrate that the PSO-tuned SMC methodology exhibits superior tracking performance, enabling the PV system to rapidly and accurately converge to the true MPP under varying weather and shading scenarios. The findings indicate that the proposed technique enhances the efficiency and reliability of PV energy harvesting in PSCs.

Solar modules under partial shading (PS) conditions will result in power and voltage characteristic curves (P-VCC) having multiple peaks. If the maximum power point cannot be obtained, the output power of the solar modules will be greatly reduced. Hence, there have been various maximum power point tracking (MPPT) control methods developed to address this problem. One alternative is to employ the meta-heuristic approach (MHA) to track the global maximum power point (GMPP). Recently, a new MHA called Bat Algorithm (BA) has performed well in the MPPT. Nevertheless, BA may fail to track the GMPP when there are some local maximum power points (LMPPs) close to the GMPP. Also, the tracking time needs to be further reduced to accommodate rapidly changing irradiance. Therefore, a combination of BA with the abandonment mechanism of Cuckoo Search (CS) is proposed to improve the tracking performance of the BA. Both simulation and experimental results show that the proposed method, as compared to BA, yields better accuracy and an improvement of convergence speed of about 35% for various P-VCCs can be achieved. Moreover, the MBA has also been tested against some of the state-of-the-art MPPT algorithms such as Particle Swarm Optimization and Grey Wolf Optimization (GWO), and the results showed the superiority of the proposed method.

Maximum power point tracking (MPPT) plays a vital role in photovoltaic (PV) system to utilize PV energy efficiently. The maximum power point (MPP) of PV system varies with atmospheric conditions and to track it, an efficient tracking system is needed. There are different MPPT algorithms available to track the maximum power. Among different MPPT techniques P&O MPPT is mostly used because of its plain structure and it is easy to implement. But conventional P&O method is slow in nature and suffers from steady state oscillations. To avoid this, this paper emphasizes on an adaptive P&O MPPT which can able to track the MPP rapidly with less steady state oscillation as compared with conventional P&O MPPT algorithm. The efficacy of the proposed method is verified considering both simulation and experimental results.

This paper presents the analysis and operation of a grid connected photovoltaic (PV)energy conversion system with an Adaptive Neuro-Fuzzy Inference System (ANFIS)based maximum power point tracking (MPPT)algorithm. Particle swarm optimization is used to train the membership functions while the least squares algorithm is used to update the consequent parameters of the ANFIS with changing operating condition of PV solar system. The MPPT algorithm maximizes conversion efficiency by adjusting the duty cycle of the buck boost converter to change the output voltage of the solar panel and hence achieving the maximum panel output power for a given set of environmental conditions. The ANFIS is trained by using a hybrid algorithm implementing least squares estimator and particle swarm optimization with data obtained by operating the system using the Perturb and Observe (P&O)MPPT algorithm. The performance of the proposed ANFIS based MPPT algorithm is validated in simulation using MATLAB/Simulink at different operating conditions. It is proven that the designed ANFIS based MPPT scheme achieves a very fast response with little oscillations while transferring maximum power from solar panel to the grid line as compared to the conventional P&O based MPPT scheme.

Dynamic global maximum power point tracking of the PV systems under variant partial shading using hybrid GWO-FLC

Among all the conventional maximum power point tracking (MPPT) techniques for a photovoltaic (PV) system that have been proposed, incremental conductance (INC) and perturb and observe (P&O) are the most popular because of their simplicity and ease of implementation. However, under partial shading conditions (PSCs), these MPPT algorithms fail to track the global maximum power point (GMPP) and instead converge into local maximum power points (LMPPs), resulting in considerable PV power loss. This paper presents a new hybrid MPPT technique combining the artificial bee colony (ABC) and P&O algorithms named ABC-P&O. The P&O technique is used to track the MPP under uniform irradiance, and only during irradiance variations is the ABC algorithm employed. The effectiveness of the proposed hybrid algorithm at tracking the GMPP, under both uniform and nonuniform irradiance conditions, was assessed by hardware-in-the-loop (HIL) tests employed by a dc–dc boost converter. Then, the ABC-P&O strategy was applied to obtain the voltage reference for the outer PI control loop, which provided the current reference to the discrete-time sliding-mode current control. The ABC-P&O algorithm has a reasonable computational cost, allowing the use of a commercial, low-priced digital signal controller (DSC) with outer voltage and inner current control loops. Many challenging tests validated that the proposed ABC-P&O technique converges fast to the GMPP with high efficiency and superior performance under different PSCs.

MPPT technique used with perturb and observe to enhance the efficiency of a photovoltaic system

K-Nearest Neighbors hybrid method for maximum power point tracking under partial shading for photovoltaic power systems

Due to the Randomness and fluctuation of the photovoltaic (PV) system, Maximum Power Point Tracking (MPPT) algorithm is employed to ensure the maximum power extraction from PV arrays, when it is connected to the grid. The previous studies have indicated that the MPPT algorithm is one of the main causes of interharmonics emission in PV systems. The MPPT algorithm parameters such as perturbation step size inevitably have a strong impact on the interharmonics in the current injected to the grid. In general, a smaller MPPT perturbation step size will reduce the interharmonics emission level, but it will result in poor tracking performance of the MPPT algorithm. Thus, there is a trade-off between the MPPT efficiency and the interharmonics emission in PV system. In this paper, an interharmonics suppression scheme with variable step size MPPT algorithm was proposed. In the suppression scheme, two voltage values near by the MPPT voltage and two tracking step size are preset. When the dc-link voltage of PV is between the two preset voltage values, it means that the PV power near its MPP and the smaller perturbation step size implemented in the MPPT algorithm. Otherwise, the bigger perturbation step size is employed. It can greatly reduce interharmonics emission level and maintain the MPPT efficiency. Simulations have been carried out to verify the effectiveness of the suppression scheme.

This study proposes a novel maximum power point tracking (MPPT) control strategy for the solar photovoltaic power system (SPPS). The proposed system adopts two solar photovoltaic modules of 430 W, which are connected to a boost converter and an MPPT controller, since the traditional MPPT algorithm (such as perturbation and observation [P&O] algorithm) can hardly reach maximum power point (MPP) under low irradiance level and partial shading conditions (PSC), which leads to the low efficiency of the SPPS. The speed of light optical path difference measurement (SLOPDM) MPPT control strategy has been developed in this study to overcome this problem. The estimation of the optical path angle difference is used as the basis for the proposed control strategy. This is done by determining the relationship between the optical path angle difference, solar photovoltaic power impedance Rspv and load Ro, and then calculating the duty cycle corresponding to the MPP, which then drives the boost converter to capture the MPP. The experimental results verify the proposed system, which shows the efficiency comparison between the SLOPDM MPPT algorithm, solar angle and horizon (SAH) algorithm, and P&O algorithm under PSC and uniform irradiance conditions (UIC) at irradiance levels of 700 W/m2 and 65 W/m2. It is evident from the comparison that the efficiency of the SLOPDM MPPT algorithm is 99% under both conditions, which is higher than the SAH and P&O algorithms. The SLOPDM MPPT algorithm can precisely, rapidly, and stably be operated at MPP. The contribution of this study is that the proposed MPPT control strategy can help achieve the high−performance of SPPS without changing the hardware circuit design and requiring any additional solar power meter. This reduces the cost and the complexity of the system significantly.