Metasurface-based terahertz TE10-TE01 mode converter.

A mode conversion from the TE 10 in WR3 rectangular waveguide to the TE 53 in an oversized circular waveguide is required to perform the cold test of a Bragg resonator for a high power 250 GHz Cyclotron Auto-Resonance Maser (CARM) under development at the Frascati ENEA research centre. High operating frequency and oversized cylindrical cavity (exceeding any previous CARM experiment) make the design particularly challenging. An initial transition, aimed at transforming the TE 10 in WR3 rectangular waveguide into the TE 11 , in a circular waveguide, is performed using a linear taper, a well-assessed device. Then a serpentine mode converter in circular waveguide with average radius of 1.48 mm and appropriate length has been adopted for the conversion into the TE 01 mode. The subsequent transducers, for not-rotating (TE 0m ) and rotating (TE 53 ) modes, are provided by means of rippled wall mode converters with small periodic perturbations of waveguide radius. The ripple period corresponds approximately to the beat wavelength (X b = 2π/(β m − β n )) with β m and β n the wavenumbers of the two interacting modes. For not-rotating modes an efficient conversion has been obtained by cascading single step TE 01 to TE 02 , TE 02 to TE 03 and TE 03 to TE 04 mode converters. For each of them, profiles, radius and number of periods have been optimized in order to obtain low levels of unwanted spurious modes, low reflection and sufficient bandwidth. As the modes to convert (TE 04 to TE 53 ) present similar wavenumbers, the most appropriate method for the conversion consists in a three-periods rippled-wall mode converter made by a helically corrugated waveguide with an average radius of 4 mm and five azimuthal variations. The longitudinal profile of the ripples has been properly smoothed to avoid steps between the circular waveguide and the corrugated converter. In this paper the conversion chain will be described and the simulation results (S-parameters, efficiency and electric field) of each single converter will be reported. Finally some considerations about the high precision micromachining technique to be used, such as copper electroforming and Computer Numerically Controlled (CNC) milling, for the construction of these high frequency components, will be presented.

In this paper, a dielectric-filled circular waveguide TM01-TE11 mode converter is proposed, which has high conversion efficiency and a wide operating bandwidth. Filling the circular waveguide with dielectric material changes the local propagation characteristics, thus achieving a phase difference between the TE11 modes in the two halves of the circular waveguide during propagation. This, in turn, facilitates the completion of mode conversion with high efficiency. Compared with the conventional radial dielectric plate, this paper improves the method of filling the dielectric inside the circular waveguide by transforming it into a coaxial structure. This is followed by the incorporation of a radial dielectric plate, a modification that has been proven to enhance the conversion efficiency and extend the operational bandwidth. The mode converter operates at 9.7 GHz, and when the dielectric filler material is polytetrafluoroethylene (PTFE), both simulation and practical studies are carried out. The simulation results demonstrate that the maximum conversion efficiency of this mode converter is 99.2%, and the bandwidth with conversion efficiency greater than 90% is nearly 21.1%. The maximum conversion efficiency in the actual test is essentially consistent with the simulation results. The validity of the design scheme of this converter and the accuracy of the simulation study are demonstrated.

This paper presents the design of a unique multimode extractor and converter of higher order modes of a circular waveguide. The multi-mode extractor couples first five circular waveguide propagation modes TE11, orthogonal TE11(o), TM01, TE21, and TE21(o) that includes the three tracking signals (i.e. sum signal, elevation signal, and azimuth signal) used in a high-frequency monopulse tracking system and two communication channels for transmitting and receiving signal at Ka band. This design is based on amplitude and phase characteristics of the higher-order modes TM01, TE21, and TE21(o) excited in circular waveguide. TE21 and TE21 (o) modes are extracted from circular waveguide to TE10 mode in rectangular waveguide by two longitudinal slots milled in the circular waveguide. TE11 mode is coupled using two coupling slots and H-plane power combiner. A turnstile junction is used to extract TM01 and TE11(o) mode. This multimode tracking system is designed both for linear or circular polarized ground earth station antennas to track orbiting satellites.

A novel mode converter that can transform coaxial transverse electromagnetic (TEM) mode into circularly polarized TE11 (CPT) mode was developed and experimentally studied with high-power microwave (HPM). The mode conversion is realized by two steps. First, the TEM mode is converted into linearly polarized TE11 (LPT) mode by the webbed-shaped balun structure. Second, the LPT mode is transformed into the CPT mode with the insertion of circular-arc diaphragms in a circular waveguide. In this paper, the principle of a mode converter working at 1.57 GHz is demonstrated, as well as the experimental results. The experimental and simulation results are in good agreement. At the central frequency, the conversion efficiency is more than 99.5%, the measured axial ratio approximates to 1.39 dB, and the power handling capacity is in excess of 1.5 GW. These measured results meet the demand for narrow-band HPM source application.

A quasi-optical mode converter for a W-band <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">TE</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">02</sub> mode gyrotron is designed, fabricated, and tested. The system consists of a step-cut waveguide launcher (cut-in-half circular waveguide) and a doubly curved reflector (an elliptical reflector and a parabolic reflector). Based on the geometric optics principle and the vector diffraction theory, the mode converter is optimized and simulated by using numerical calculations. The simulation results show that the good Gaussian mode is converted from the circular waveguide <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">TE</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">02</sub> mode, and the conversion efficiency is 77.9%. Experimental measurements are performed on a quasi-continuous wave gyrotron operating in the <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">TE</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">02</sub> mode at W-band and show a good agreement with theoretical predictions.

In recent years, R&D for pulse compression and power distribution systems for the Next Linear Collider has led to the invention of many novel rf components, some of which must handle up to 600 MW of pulsed power at X‐band. These include passive waveguide components, active switch designs, and non‐reciprocal devices. Among the former is a class of multi‐moded, highly efficient rf components based on planar geometries with overmoded rectangular ports. Multi‐moding allows us, by means of input phasing, to direct power to different locations through the same waveguide. Planar symmetry allows the height to be increased to improve power handling capacity. Features that invite breakdown, such as coupling slots, irises and H‐plane septa, are avoided. This class includes hybrids, directional couplers, an eight‐port superhybrid/dual‐mode launcher, a mode‐selective extractor, mode‐preserving bends, a rectangular mode converter, and mode‐mixers. We are able to utilize such rectangular waveguide components in systems incorporating low‐loss, circular waveguide delay lines by means of specially designed tapers that efficiently transform multiple rectangular waveguide modes into their corresponding circular waveguide modes, specifically TE10 and TE20 into circular TE11 and TE01. These extremely compact tapers can replace well‐known mode converters such as the Marié type. Another component, a reflective TE01‐TE02 mode converter in circular waveguide, allows us to double the delay in reflective or resonant delay lines. Ideas for multi‐megawatt active components, such as switches, have also been pursued. Power‐handling capacity for these is increased by making them also highly overmoded. We present a design methodology for active rf magnetic components which are suitable for pulse compression systems of future X‐band linear colliders. We also present an active switch based on a PIN diode array. This component comprises an array of active elements arranged so that the electric fields are reduced and the power handling capability is increased. Novel designs allow these components to operate in the low‐loss circular waveguide TE01 mode. We describe the switching elements and circuits.

Mode converters (MCs) play an essential role in mode-division multiplexing (MDM) systems. Numerous schemes have been developed on the silicon-on-insulator (SOI) platform, yet most of them focus solely on the conversion of fundamental mode to one or two specific higher-order modes. In this study, we introduce a hybrid shape optimization (HSO) method that combines particle swarm optimization (PSO) with adjoint methods to optimize the shape of the S-bend waveguide, facilitating the design of arbitrary-order MCs featuring compactness and high performance. Our approach was validated by designing a series of 13 μm-long MCs, enabling efficient conversion between various TE modes, ranging from TE0 to TE3. These devices can be fabricated in a single lithography step and exhibit robust fabrication tolerances. Experiment results indicate that these converters achieve low insertion losses under 1 dB and crosstalks below -15 dB across bandwidths of 80 nm (TE0-TE1), 62 nm (TE0-TE2), 70 nm (TE0-TE3), 80 nm (TE1-TE2), 55 nm (TE1-TE3), and 75 nm (TE2-TE3). This advancement paves the way for flexible mode conversion, significantly enhancing the versatility of on-chip MDM technologies.

In a waveguide‐based coupled‐mode system, various mode conversions are achieved by designing mode evolution procedures. However, the differences of refractive indices among modes exceed the capability of conventional tuning mechanism, so most reported mode manipulation devices can only realize fixed mode conversions. This paper introduces the cladding medium switching strategy to the subwavelength grating waveguide‐based coupled‐mode system, and proposes a reconfigurable mode converter on silicon nitride platform. This work systematically analyzes the phase matching conditions on a coupled‐mode system. Results show that for both whole and partial upper‐cladding switchable, it is possible to achieve reconfigurable mode conversions. For whole cladding switchable case, this work demonstrates a double‐state mode converter, which converts the input mode to TE2 and TE1 modes under cladding refractive indices of 1 and 1.7. This work expands it to triple‐state mode conversion with window‐style cladding, which converts the input to TE2, TE1, and TE0 modes under cladding of 1, 1.54, and 1.7. The optical bandwidths are relatively large, and the conversion efficiencies exceed 56% for all cases. The mechanism provides a non‐volatile and energy‐efficient way for tunable mode conversions, which is promising for applications in optical networks, communications, and sensors, etc.

In this paper, a novel X-band TM01–TE01 mode converter for high-power microwave (HPM) system is proposed. To realize the compact design, a helical corrugated waveguide with large deformation is employed to convert the TM01 mode into TE01 mode. By optimizing the structure parameters, the simulation results demonstrate that the maximum conversion efficiency of the proposed TM01–TE01 mode converter reaches 98.8% at 9.2 GHz. Moreover, this mode converter exhibits a conversion efficiency of over 95% in the operation band from 8.7 to 9.42 GHz, and the power capacity of the mode converter reaches GW-level in theory. More importantly, the overall longitudinal and transverse dimensions of the mode converter are less than three wavelengths. The results show the compact structure and high conversion efficiency of this mode converter, which has great potential application value in the HPM system.

A compact mode converter that transforms TM01 circular waveguide mode to TE10 rectangular waveguide mode is investigated. It consists of a circular waveguide with a short circuit terminal and a rectangular waveguide which is perpendicular to the circular waveguide. Simulation results show that conversion efficiency of the mode converter is about 99.8% at central frequency of 1.75 GHz, and the total return loss is approximately -30 dB. The experimental results are well consistent with the computer simulation, which demonstrates the feasibility and high power handling capacity of the mode converter.

Using the concept of a metallic cylinder and a linearly tapered metallic baffle loaded in a circular waveguide to convert TM02 circular waveguide mode into TE11 circular waveguide mode, a novel and compact circular waveguide TM02-TE11 mode converter is designed, fabricated, and measured. The detailed design methods, experimental setups and results are presented in this study. Simulation results show that the purity of output fundamental TE11 mode of the converter exceeds 99.6% for an operating frequency of 9.4 GHz and the power capability is as high as 1.66 GW, the mode conversion efficiency is more than 90% from 9.23 to 9.83 GHz band and the relative bandwidth is about 6.38%. A good agreement between measurements and simulations is observed. The circular waveguide TM02-TE11 mode converter has many advantages, such as the simple structure, coaxial input and output, high conversion efficiency, proper bandwidth and high power-handling capability. When used in the field of high power microwave transmission and radiation, the proposed converter could significantly enhance the compactness of all the radiation systems.

An analytical method to estimate the scattering of RF power into multiple modes inside a nonuniform waveguide using perturbation techniques is presented. This method is quite general, much faster than numerical methods, and may be applied to a wide variety of nonuniform waveguides. We have used this method to design and analyze a three-section mode transformer that converts a TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> circular waveguide mode to a TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">20</sub> rectangular waveguide mode. This mode converter is specially suitable for use in ultra-high-power applications. Due to the complexity of the problem, we have used the symbolic solver Mathematica to produce most of our analytical results. The results match within reasonable accuracy with High Frequency Structure Simulator field solver simulations. We also present the application of this mode converter to variety of ultra-high-power microwave components and experimentally show the performance of these devices.

In this paper, we proposed the new rectangular waveguide-NRD waveguide transition in which the transition function about the standard waveguide is built in within the NRD waveguide ifself. The newly proposed rectangular waveguide-NRD waveguide transition was realized use of NRD waveguide input/output side wall thickness and hole width. In the case of the wall thickness, it was nearly identical with the half of the NRD waveguide guide wavelength and the width of an hole was nearly coincide with the length of the long side of the standard waveguide connected with the NRD waveguide. This kind of the principles is applicable to be unrelated with the frequency band. In this paper, it made in 38 GHz band with the rectangular waveguide-NRD waveguide transition and the feasibility was confirmed. In the back-to-back structure, the rectangular waveguide-NRD waveguide transition manufactured in 38 GHz band has the insertion loss less than 0.4 dB and also has the return loss less than 20 dB.

To accurately measure the performance of dielectric loaded circuits for gyrotron traveling wave tubes, a novel topological structure to generate the TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">21</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> or TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> (superscript represents circular waveguide) mode is proposed and verified in this paper. The topology is constituted by an overmoded TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">10</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">□</sup> to TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">20</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">□</sup> (superscript represents rectangular waveguide) mode converter with multiple matching steps and a taper from TE20 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">□</sup> to TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">21</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> or TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> mode. This topology allows the TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">21</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> or TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> mode to be excited by changing the taper dimensions. Simulation results reveal that the TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">21</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> and TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">O</sup> mode converters, respectively, have a 1-dB bandwidth of 12.8 and 9.3 GHz with an excellent performance. Converters for the back-to-back millimeter-wave measurements were fabricated with computerized numerical control and wire cutting techniques. Vector network analyzer measurements are in good agreement with the simulations.

The HE11 hybrid mode, propagating in an overmoded corrugated circular waveguide, is widely used for low loss transmission of high-power microwaves. Due to the inherent broadband frequency behaviour, this will be also essential for future broadband high-power radar applications, like space debris observation in low earth orbit (LEO). A promising amplifier concept for such radar sensors is a helical gyro-TWT. However, since the HE11 hybrid mode is not suitable for electron-beam-wave interaction in this kind of vacuum electron device, an additional mode converter is required. The present paper addresses the design procedure of a broadband high-power mode converter, designed for a helical gyro-TWT intended for future broadband high-power radar applications in the W-band. The interaction mode of the helical gyro-TWT under consideration can be easily transferred to the circular waveguide TE11 mode. Therefore, a TE11 ↦ HE11 mode converter is addressed here. The design procedure is based on a scattering matrix formalism and leads to a high HE11 mode content of ≥98.6% within the considered frequency range from 92 GHz to 100 GHz. Inside this frequency band, the mode content is even better and reaches ≈ 99.7% at ≈95 GHz. This allows broadband frequency operation of a helical gyro-TWT and is suitable for broadband high-power radar applications.