MU-MISO Transmission with Limited Feedback

In Multi-user MIMO (MU-MIMO) downlink system, suitable user selection schemes can improve spatial diversity gain. In most of previous studies, it is always assumed that the base station (BS) knows full channel state information (CSI) of each user, which does not consider the reality. However, there are only limited feedback bits in real system. Besides, user fairness is often ignored in most of current user selection schemes. To discuss the user fairness and limited feedback, in this paper, the user selection scheme with limited feedback bits is proposed. The BS utilizes codebook precoding transmitting strategy with LTE codebook. Furthermore, this paper analyzes the influence of the number of feedback bits and the number of users on user fairness and system sum capacity. Simulation results show that in order to achieve better user fairness, we can use fewer bits for feedback CSI when the number of user is small, and more feedback bits when the number of users is large.

A multihop regenerative relay system is considered. We explore adaptive power allocation (PA) under a total power constraint to minimize the system error probability when the perfect channel state information (CSI) is known at the transmitters. We propose adaptive PA schemes with limited feedback when the transmitters have no perfect knowledge of CSI. Simulation results demonstrate the good performance of the proposed PA scheme with perfect CSI. When no perfect CSI is available at the transmitters, the proposed PA schemes with a small number of feedback bits are able to achieve very close performance to the adaptive PA with perfect CSI.

Channel state information (CSI) at the base station (BS) is crucial to achieve beamforming and multiplexing gains in multiple-input multiple-output (MIMO) systems. State-of-the-art limited feedback schemes require feedback overhead that scales linearly with the number of BS antennas, which is prohibitive for 5G massive MIMO. This paper proposes novel limited feedback algorithms that lift this burden by exploiting the inherent sparsity in double-directional MIMO channel representation using overcomplete dictionaries. These dictionaries are associated with angle of arrival and angle of departure that specifically account for antenna directivity patterns at both ends of the link. The proposed algorithms achieve satisfactory channel estimation accuracy using a small number of feedback bits, even when the number of transmit antennas at the BS is large-making them ideal for 5G massive MIMO. Judicious simulations reveal that they outperform a number of popular feedback schemes and underscore the importance of using angle dictionaries matching the given antenna directivity patterns, as opposed to uniform dictionaries. The proposed algorithms are lightweight in terms of computation, especially on the user equipment side, making them ideal for actual deployment in 5G systems.

Accurate channel state information (CSI) at base station (BS) is the key to achieve full multiplexing and diversity gain in traditional multiple-input multiple-output (MIMO) systems. In frequency-division-duplex (FDD) systems, it is obtained through downlink training and uplink feedback. However, the training and feedback overhead in massive MIMO systems is unacceptable for the large number of antennas equipped at BS. To reduce the CSI feedback overhead and improve CSI quantization accuracy, we propose a limited feedback scheme for spatio-temporal correlated massive MIMO channel. The proposed scheme jointly performs Karhunen-Loève transform (KLT) and polar-cap quantization on CSI. For the compactly deployed antennas at BS, there exists spatial correlation in massive MIMO channel. When the user equipment (UE) moves slowly, adjacent channels feature temporal correlation. The high dimensional and spatial correlated CSI is compressed through KLT. Then the compressed CSI is normalized to be isotropic to perform polar-cap quantization. Simulation results show that the proposed scheme is capable of improving the sum-rate performance with limited feedback bits for massive MIMO systems.

The availability of the Channel State Information (CSI) at the transmitter is crucial for the precoder design in Multi-user Multiple Input Single Output (MU-MISO) systems. In Frequency Division Duplex (FDD) systems, CSI can be just available at the transmitter through a limited feedback channel [1], where we assume that each user estimates, normalizes, and finally quantizes its channel direction with a finite number of quantization bits relayed back error-free and quasi-instantaneous. In this paper, we consider a simple sequential uniform scalar quantization (SQ) scheme of the individual components (real and imaginary parts) of the Channel Direction Information (CDI). Although vector quantization (VQ) schemes [2], [3] still outperform this scalar scheme in terms of quantization error and Bit Error Rate (BER), the former scheme suffers from an exponential search complexity and high storage requirements at the receiver for high number of feedback bits.

Channel state information (CSI) acquisition is one of the major challenges for massive MIMO systems to enable high efficiency MIMO transmissions. Limited feedback schemes, which quantize CSI into limited number of bits and feed these bits back to the base station (BS), are widely used in real-life mobile networks for BSs to obtain downlink CSI. Practical limited feedback schemes usually have large feedback granularity and introduce severe nonlinear quantization error due to the constraint on feedback overhead. It is hard for legacy signal processing technologies to reconstruct CSI accurately for high efficiency downlink transmissions. Different from the legacy signal processing technologies, deep neural networks trained with big data have strong abilities to fit any nonlinear functions and learn the complex signal model behind the big data, which is a useful tool to solve problems that are nonlinear or hard to be described mathematically. Motivated by these observations, we consider a deep learning based approach for BS receivers to reconstruct CSI based on the limited feedback bits from user equipment (UE). The CSI reconstruction is similar with the image super-resolution which reconstructs a high resolution image from a low resolution one based on the structure information learned by the neural network itself. Performance evaluations demonstrate that the proposed method outperforms the legacy algorithms. The improvement on spectrum efficiency is about 25%. It can also reconstruct the CSI with lower density reference signal (RS) than that in current specification, e.g., the RS density can be 1/32 of current one. Therefore, the reference signal and feedback overhead can be reduced with our method. These results show the potential gain of applying deep learning to physical layer signal processing at the receiver side only, which has little air-interface impact and does not require much effort on enhancing network specifications. Therefore, it is feasible to be deployed in current 5th generation mobile networks with the pace of network evolutions, and opens the gate of intelligent physical layer design for future generations of mobile networks.

The multiuser MIMO (MU-MIMO) systems tend to have inter-user interference in practical systems with limited feedback. Practical MU-MIMO systems with limited feedback can be divided into two classes in general. One is zero-forcing beamforming (ZFBF), and the other is per user unitary rate control (PU <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> RC) which is an extended version of random beamforming (RBF). To improve performance, ZFBF needs more feedback bits, and PU <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> RC needs a larger number of users. We propose a new hybrid MU-MISO system which has the advantages of the two MU-MIMO schemes simultaneously, and analyze the sum-rate performance and the quantization error of the hybrid scheme. The analysis shows how the number of feedback bits, the number of users, and the signal power affect the sum-rate. The throughput scaling laws are also derived in the high and the medium SNR regimes. Simulation results show that the proposed hybrid MU-MISO system performs better than either of the two MU-MIMO systems with the same number of feedback bits. Another advantage is that it has lower complexity for codeword search since it has a hierarchical codebook structure.

Reconfigurable intelligent surfaces (RISs) represent a pioneering technology to realize smart electromagnetic environments by reshaping the wireless channel. Jointly designing the transceiver and RIS relies on the channel state information (CSI), whose feedback has not been investigated in multi-RIS-assisted frequency division duplexing systems. In this study, the limited feedback of the RIS-assisted wireless channel is examined by capitalizing on the ability of the RIS in channel customization. By configuring the phase shifters of the surfaces using statistical CSI, we customize a sparse channel in rich-scattering environments, which significantly reduces the feedback overhead in designing the transceiver and RISs. Since the channel is customized in terms of singular value decomposition (SVD) with full-rank, the optimal SVD transceiver can be approached without a matrix decomposition and feeding back the complete channel parameters. The theoretical spectral efficiency (SE) loss of the proposed transceiver and RIS design is derived by considering the limited CSI quantization. To minimize the SE loss, a bit partitioning algorithm that splits the limited number of bits to quantize the CSI is developed. Extensive numerical results show that the channel customization-based transceiver with reduced CSI can achieve satisfactory performance compared with the optimal transceiver with full CSI. Given the limited number of feedback bits, the bit partitioning algorithm can minimize the SE loss by adaptively allocating bits to quantize the channel parameters.

To maintain a specific degree of multiplexing gain with limited feedback in multiple-input/multiple-output broadcast channels, the number of feedback bits has been increased linearly with the signal-to-noise ratio (SNR) measured in decibel, and conditions for the slope of this increase have been derived in previous studies. However, previous studies mostly focused on the chordal distance (ChD) for channel quantization, although it is not an optimally designed distance measure. Thus, the possibility exists that the same degree of multiplexing gain can be obtained by using fewer feedback bits than the existing method requires. In this paper, we propose an optimal distance measure that can maximize the multiplexing gain achieved by limited-feedback-based block diagonalization over broadcast channels. Then, we provide a sufficient condition for the number of feedback bits to achieve a specific degree of multiplexing gain with the proposed method. The sufficient number of feedback bits is given by a linear function of the SNR (decibel) as in previous studies, but the slope of the linear increase can be much less than that obtained in previous studies. As a consequence, the proposed method achieves higher multiplexing gain and corresponding throughput than the existing methods with the same number of feedback bits.

The provision for spectrally efficient multicast broadcast services (MBS) is one of the key functional requirements for next generation wireless communication systems. The challenge inherent to MBS is to ensure that all MBS users can be served, and one effective solution to this problem is to employ MIMO multicast transmit precoding. In previous works on MIMO multicast transmit precoding design, the authors either assumed (1) perfect transmitter-side channel state information (CSIT) or (2) special channel conditions that facilitate precoder design with imperfect CSIT. In this paper, we focus on transmit precoding design for MBS where the CSIT is obtained via limited feedback. In addition, we analyze the average minimum receive signal-noise-ratio (RxSNR) among the MBS users and study the order of growth with respect to the number of MBS users, the number of feedback bits, and the number of transmit antennas. Finally, we propose a threshold based feedback reduction scheme and study the tradeoff between feedback cost and performance loss.

In this paper, we consider the downlink of a multiuser wireless communication system with multiple antennas at the base station and users each with a single receive antenna. It is known that when channel state information (CSI) is available at the transmitter a large performance gain can be achieved. In a system employing time-division duplexing (TDD), CSI can be obtained at the base station if there is reciprocity between the forward and reverse channels. CSI can also be conveyed from the users to the base station via a limited-rate feedback channel in a frequency-division duplexing (FDD) system. In any case, channel estimation errors are inevitable due to the presence of background noise in the estimated signal and due to the finite number of feedback bits used in a limited-rate feedback system model. In this paper, we first consider the general case when partial CSI is available at the transmitter. We derive an MMSE based precoding technique that considers channel estimation errors as an integral part of the system design. Using rate-distortion theory and the generalized Lloyd vector quantization algorithm, we then specialize our results for the more practical limited-rate feedback system model. Compared to previously proposed precoding techniques such as channel inversion and regularized channel inversion, it is shown that the proposed precoding technique significantly improves the average bit error rate (BER) in the system. Furthermore, the performance of the proposed technique is investigated in the high signal-tonoise ratio (SNR) regime. It is shown that the proposed technique suffers from a ceiling effect that asymptotically limits the system performance.

In a wireless multi-user system using multiple antennas, full multiplexing gain can be achieved through perfect channel state information (CSI) at the base station (BS). However, because of the limitations on the feedback rate and of standard requirements, such as the 3GPP, it is difficult to obtain perfect CSI, or even partial CSI with the extremely large number of feedback bits needed at the region of high signal-to-noise ratios (SNR) in practical systems. Instead of a feedback channel resource, this paper considers another resource for the system, a cooperation channel, which can be used by users to participate in cooperation in a broadcast fading channel. The cooperation among users in a multi-user system has the effect of transforming it into a cooperative point-to-point MIMO system. This paper analyzes the cooperation channel gain and the mobile power used in a cooperation channel to maintain a constant rate gap against the zero-forcing beamforming scheme with full CSI at the BS. In addition, the performance results of this proposed cooperation strategy are provided by computer simulations.

This paper investigates a precoding method in downlink multiuser multiple-input multiple-output (MIMO) transmission with multiple base station (BS) cooperation, where each user device basically feeds back the instantaneous channel state information (CSI) to only the nearest BS, but the users near the cell edge additionally feedback the instantaneous CSI to the second nearest BS among the cooperating BSs. Our precoding method is categorized as a form of multi-cell processing (MCP) [5], in which the transmission information to a user is shared by the cooperating BSs in order to utilize fully the degrees of freedom of the spatial channel, and is based on block diagonalization of the channel matrix. However, since some elements of the channel matrix are unknown, we allow partially non-orthogonal transmission. More specifically, we allow inter-user interference to users with limited instantaneous CSI feedback from the channel where the instantaneous CSIs of those users are not obtained at the BSs. The other sources of inter-user interference are set to zero based on the block diagonalization of the channel matrix. The proposed method more efficiently utilizes the degrees of freedom of the spatial channel compared to the case with full orthogonal transmission at the cost of increased inter-user interference. Simulation results show the effectiveness of the proposed method compared to the conventional approaches, which can accommodate the partial CSI feedback scenario, from the viewpoints of the required transmission power and achievable throughput.

We consider a precoding method in downlink multiuser multiple-input multiple-output (MIMO) transmission with multiple base station (BS) cooperation where some of the instantaneous channel state information (CSI) is not available at the BSs. The proposed precoding method is based on block diagonalization of the channel matrix. However, since some elements of the channel matrix are unknown, we allow a partially non-orthogonal transmission. More specifically, we allow inter-user interference to users with limited instantaneous CSI feedback from the channel where the instantaneous CSI of that user is not obtained at the BSs. The other inter-user interferences are set to zero based on the block diagonalization of the channel matrix. The proposed method efficiently uses the degree of freedom of the spatial channel compared to the case with full orthogonal transmission at the cost of increased inter-user interference to the users with limited instantaneous CSI feedback. Simulation results show that the proposed method increases the capacity for a given transmission power or decreases the transmission power for a given capacity requirement compared to the case with full orthogonal transmission.

This paper considers a downlink cellular network where multi-antenna base stations (BSs) simultaneously serve their associated multi-antenna users. Each BS is distributed according to a homogeneous Poisson point process and uses zero-forcing beamforming for spatial division multiplexing with partial channel state information (CSI). During downlink transmission, each user combines the multiple antenna outputs and quantizes the CSI to feed back to its associated BS. Specifically, this paper focuses on antenna combining at the receiver. Conventional quantization-based combining (QBC) effectively reduces the quantization error; however, inter-cell interference in the cellular networks degrades the QBC gain. This degradation is analyzed using a spherical-cap approximation of vector quantization (SCVQ). From the SCVQ, the ergodic spectral efficiency and the optimal number of feedback bits are investigated, and it is shown that the QBC degrades the gain of the effective channel. To address this problem, an optimization solution is proposed that selects the antenna combining to maximize the spectral efficiency. The solution is also derived by considering the expected beamforming vectors of other cells. It is demonstrated by simulation that the proposed solution outperforms the conventional methods.