Multi-strategy structural damage detection based on included angle of vectors and sparse regularization

The [Formula: see text] regularization is usually used to deal with the problems of under-determinacy and measurement noise for the conventional sensitivity-based model updating damage detection methods. However, the [Formula: see text] regularization technique often provides overly smooth solutions and thus cannot exhibit the sparsity of the structural damage due to the promotion of the 2-norm term on smoothness. In the study, a structural damage detection method is proposed based on an improved modal flexibility sensitivity function and an iterative reweighted [Formula: see text] (IR[Formula: see text] regularization. Specifically, the sensitivity function is established by introducing changes in the mode shapes into the derivative of eigenvalue and can be applied to identify the localized damage more accurately. Additionally, IR[Formula: see text] regularization is proposed to deal with the ill-posed problem of damage detection in a noisy environment. The proposed IR[Formula: see text] regularization is compared with the [Formula: see text] and [Formula: see text] regularizations through a numerical and an experimental examples. The numerical and experimental results indicate that the IR[Formula: see text] regularization can more accurately locate and quantify the single and multiple damages under the noise situation. The maximum identification errors are only 5.16% and 5.67%, respectively. Moreover, compared to the basic modal flexibility sensitivity function, the improved function is more sensitive to the damage. The maximum identification error of the improved function is less than 6%, while the relative errors are significantly larger in the basic function.

In this study, a two-stage damage detection procedure using a new approximation of modal strain energy (MSE) value is developed to boost the accuracy of structural damage localization in plate-type structures. The MSE is calculated using the center differential method for both intact and damaged states. The new formulas to approximate MSE are developed based on the nine-node isometric quadrilateral element that eliminates boundary conditions’ effect on damage detection results. The modal assurance criteria (MAC) is used as an indicator to choose the mode shapes with the best damage detection results. A global and a local MSE are proposed to enhance the accuracy of detecting the location of structural damage. An aluminum plate is used to verify the effectiveness of the proposed procedure with several damage scenarios. The results show that the new estimation of MSE value combined with MAC and the two-step MSE procedure can improve the accuracy of identifying the damage location compared to the original MSE procedure.KeywordsDamage detectionModal assurance criteriaModal strain energyPlate-type structureStructural health monitoring

As one of the most common structural forms in port engineering, the operation environment of high-pile wharf is quite harsh and complex, and its pile foundation often produces structural damage of different degrees. Until now, there is a lack of efficient, safe and economic damage detection methods. A novel and precise real-time structural damage detection (SDD) method using both finite element modelling (FEM) and 1D convolutional neural networks (CNNs) is established in this study. The results indicate that the proposed method could accurately identify the presence and location of damage in real time. The results also demonstrated that the proposed 1D CNNs based model are more sensitive to the longitudinal and lateral displacement responses of the high-pile wharf structure.

Two-stage structural damage detection using fuzzy neural networks and data fusion techniques

Substructuring approaches possess many superiorities over traditional global approaches in damage identification because large-size global structures are replaced by small and manageable substructures. This paper proposes a substructural time series model for locating and quantifying the damage in complex systems. A substructural autoregressive moving average with exogenous inputs (ARMAX) model is established to extract the frequencies and mode shapes of substructures as indicators for damage detection. The detection of structural damage is essentially an inverse problem, and the damage in structure bears sparse properties. The inverse problem of substructural damage identification is efficiently solved via sparse regularization, and structural damage can be located and quantified through the nonzero terms in the solution vector. The accuracy of the proposed method is demonstrated by the numerical simulation of a frame structure and shaking table test of a shear building structure. As the substructural properties are more sensitive to local structural damage than the global properties, the substructural ARMAX model is quite accurate and efficient to be used in the damage identification of a complex system.

Experimental system identification of the dynamics of a vibro-impact beam with a view towards structural health monitoring and damage detection

Application of two-stage evaluation and optimization update methods for the structural damage detection of a portal beam structure

Vibration-based damage detection for structural connections using incomplete modal data by Bayesian approach and model reduction technique

Efficient wind energy harvesting becomes more and more important as a consequence of the increasing interest in renewable energy in the European Union [1]. This leads to growing sizes of wind turbines (WTs), and with it, larger WT blades (WTBs). The structural designs of these WTBs are created to optimize the potential energy output, where low mass is a key requirement. However, high flexibilities and lower buckling capacities are further results of these developments [2], thus certain damage scenarios become significant. Intelligently designed structural health monitoring (SHM) systems can help to reduce the associated operations and maintenance costs. Even though, several techniques are already developed for structural damage detection (SDD) in WTBs, the majority of these methods is not suitable for inservice measurements. This paper presents a SDD and structural damage localization (SDL) method based on the partial autocorrelation function (PACF) of vibration responses. The approach is applied to a numerical model of a large WTB, where the acceleration responses are obtained from transient dynamic simulations with a simplified aerodynamic loading approach. The novel damage sensitive feature (DSF) is developed as the Mahalanobis distance between a baseline and current vector of PACF coefficients. First, numerical modal analysis of the finite element (FE) WTB model is performed in order to estimate the effect of a disbonding damage scenario on the vibration characteristics. Second, the behaviour of the PACF for time series of the healthy system is discussed. Third, the SDD results on the basis of statistical hypothesis testing are assessed for two selected sensor locations and increasing damage extents. Finally, the performance of the proposed DSF with respect to SDL is illustrated for multiple locations on the WTB’s surface. This study demonstrated the efficiency of a DSF based on the PACF for SDD and SDL, which is promising for future developments of vibration-based SHM techniques in WTBs.

Structural damage detection using digital video imaging technique and wavelet transformation

This research proposed and verified an innovative method to identify and locate structural damage using only the response of operational vibration, that is the displacement acquired by a non-contact optical method. The most efficient and economical way to detect damage within the structure is to monitor its structural health while in operation. However, the uncertainties and the randomness of ambient vibrations due to the operation and environments cause a challenge in conducting the operational analysis. Current technology limits the ability to collect data on the properties of the structure without the interruption of operation. Frequencies and mode shapes have been widely used in structural damage detection, but they are not sensitive enough and cannot provide sufficient information for identifying damage locations and their quantification. Therefore, the goal of this research is to design and verify a method to detect the damage, as well as its location and severity, of structures in operation without any physical contacts for data acquisition (i.e., non-contact based structural health monitoring (SHM)). Three algorithms are integrated into this SHM process. The first algorithm is the determination of structural characteristics (frequencies and mode shapes) of a vibrating structure from output-only data. Stochastic Subspace Identification (SSI) method is applied to measured displacements over time to extract the structural characteristics. The second algorithm is to estimate the scaling factor. The mode shapes obtained from the output-only model analysis are unscaled due to the absence of the information of input excitation forces. Mass Change Modal Scale (McMS) algorithm is used to estimate the modal scaling factors and determine the scaled mode shapes. The third algorithm is to estimate the structural system matrices (i.e., mass and stiffness matrices) and assess the damages. A Finite Element Model Updating (FEMU) is applied and the system matrices are updated from frequencies and scaled mode shapes. The damage within the structure can then be detected by analysing changes in mass and stiffness matrices. All three phases are verified by numerical simulation and laboratory experiments with deflections acquired by non-contact optical methods through video system. At last, to achieve the non-contact based SHM, a modal scaling method based on temperature change is proposed and verified by numerical simulation. Experimental program reveals that the proposed algorithm using McMS method is applicable to detect damage locations and their mass losses. With proposed non-contacted based SHM, the limitations of contact based sensor can be addressed, and the structural damage

Damage detection of structures is important to ensure the service of civil engineering infrastructures. Many techniques have been developed for damage detection of structures in the literature. In this paper a new technique, a so called MAC-FMSO technique, is developed by using a combination of Modal Assurance Criterion (MAC) and Fast Multi Swarm Optimization (FMSO) techniques. By using this method, not only the damage location can be assured, but also the loss of strength and loss of stiffness of structures might be quantified. The first stage is to obtain the damaged member’s location by using second level of damage detection techniques, such as mode shape curvature method, damage locating vector, or strain energy method. After obtaining the damaged member, the MACFMSO technique is used to obtain the loss of stiffness from the candidate of damaged members. The results show that the MAC-FMSO algorithm has the ability to predict the loss of stiffness in the damaged members. In this case, the MAC-FMSO technique can be considered as an efficient and effective tool at the third level of damage detections. This is because this technique successfully measures the loss of strength or loss of stiffness of the damage member or part of structures. At the end of the paper, the MAC-FMSO technique is applied to predict the location of damage and loss of stiffness of three different structures. The first application is a simply supported beam with three different damage scenarios; the second application is a 13-bar plane truss structure with two different scenarios, and the third application is a shear building structure with three different scenarios. The results of simulation show that the MAC-FMSO technique can accurately predict the loss of stiffness of the damaged member as well as the location of the damage.

The representation of structural dynamics in the absence of physics-based models, is often accomplished through the identification of parametric models, such as the autoregressive with exogenous inputs, e.g. ARX models. When the structure is amenable to environmental variations, parameter-varying extensions of the original ARX model can be implemented, allowing for tracking of the operational variability. Yet, the latter occurs in sufficiently longer time-scales (days, weeks, months), as compared to system dynamics. For inferring a “global”, long time-scale varying ARX model, data from a full operational cycle has to typically become available. In addition, when the sensor network comprises multiple nodes, the identification of long time-scale varying, vector ARX models grow in complexity. We address these issues by proposing a distributed framework for structural identification, damage detection and localization. Its main features are: (i) the individual estimation of local, single-input-single-output ARX models at every operational point; (ii) the long time-scale representation of each individual ARX coefficient via a Gaussian process regression, which captures dependency on varying Environmental and Operational Conditions (EOCs); (iii) the establishment of a distributed residual generation algorithm for damage detection, which produces time-series of well-defined stationary statistics, with detected discrepancies used for damage diagnosis; and, (iv) exploitation of ARX-inferred mode shape curvatures, obtained via ARX-inferred global state-space models, of the healthy and damaged states, for damage localization. The method is assessed via application on two numerical case studies of different complexity, with the results confirming its efficacy for diagnostics under varying EOCs.

Damage can be identified using generalized flexibility matrix based methods, by using the first natural frequency and the corresponding mode shape. However, the first mode is not always appropriate to be used in damage detection. The contact interface of rod-fastened-rotor may be partially separated under bending moment which decreases the flexural stiffness of the rotor. The bending moment on the interface varies as rotating speed changes, so that the first- and second-modal parameters obtained are corresponding to different damage scenarios. In this paper, a structural damage detection method requiring single nonfirst mode is proposed. Firstly, the system is updated via restricting the first few mode shapes. The mass matrix, stiffness matrix, and modal parameters of the updated system are derived. Then, the generalized flexibility matrix of the updated system is obtained, and its changes and sensitivity to damage are derived. The changes and sensitivity are used to calculate the location and severity of damage. Finally, this method is tested through numerical means on a cantilever beam and a rod-fastened-rotor with different damage scenarios when only the second mode is available. The results indicate that the proposed method can effectively identify single, double, and multiple damage using single nonfirst mode.

Structural damage detection by nondestructive methods is highly desirable. Changes in modal parameters such as frequency, damping, and mode shape are particularly inviting. Evidence is presented here that reveals that static deflection can, in many cases, be a more sensitive predictor of structural damage than frequency. The reasons for this are illuminated within, and hinge on very fundamental issues about the very nature of structural response. Furthermore, static deflection measurements are often easier to make, with higher levels of accuracy than dynamic measurements. Comparisons are made between theoretical models and experimental results for simple structures, with extensions given to more complex structures.