Nonlocal variational theory and optimal control problems

In this paper, we consider a class of optimal switching control problems with multiple time-delays and a cost on changing control and subject to terminal state constraints. A computational method involving three stages is developed to solve this class of optimal control problems. First, by parameterizing the control function with piecewise-constant functions, the optimal switching control problem is approximated by a sequence of finite-dimensional optimization problems, where the original switching times, the control heights and the control switching times are decision variables. Second, by introducing new variables, the total variation of the control variables is transformed into an equivalently smooth function. Third, we convert the constrained optimization problem into one only with box constraints by an exact penalty function method. The gradients of the cost functional are then derived, which can be combined with any gradient-based optimization method to determine the optimal solution. Finally, a numerical example is given to illustrate the effectiveness of the proposed algorithm.

For Meyer type optimal control problems the principle of optimality states that every subarc of an optimal solution that extends to the final time furnishes again a solution to the same optimal control problem, only with different initial conditions. Through a simple counter example it is shown in this paper that this principle is not satisfied, in general, for solutions obtained from a standard collocation approach. Introduction The principle of optimality [1] is one of the most intuitive and yet most fundamental theorems in the theory of optimal control. Its basic statement is that for Meyer type optimal control problems every subarc of an optimal solution that extends to the final time furnishes again a solution to the same optimal control problem, only with different initial conditions. This theorem has significant implications. For example, it is the starting point for the derivation of the Hamilton-Jacobi-Bellman equations [2] and it is the underlying principle in Bellman's dynamic programming approach [1], [3]. The present paper shows that the principle of optimality is not satisfied, in general, for solutions obtained from a standard collocation approach[4]. For a simple example whose collocation solution can be generated analytically it is shown that further improvements are possible along an optimal collocation solution if the design parameters along a number of leading nodes are frozen and the remainder of the trajectory is re-optimized. I. Continuous Optimal Control Problem In this section of the paper we introduce a simple class of optimal control problems without state and control constraints. In Section 1.2 we present the associated necessary conditions for optimality [2], [5]. For ease of notation we assume that the right-hand side of the 'Supervising Engineer, Member AIAA, t Senior Engineer, Member AIAA, *17 Research Drive, Hampton, VA 23666. ^Graduate Student, Member AIAA, Department, 304 Town Engineering, Ames, IA 50011 equations of motion does not depend explicitly on time t. This does not represent a loss of generality, as it is always possible to transform explicit time dependence away through the introduction of an additional, timelike state variable. 1. Problem Formulation Let us consider the following class of optimal control problems: min «e(Pwc[*o,*/]), (1) subject to the conditions ±(t) = /(*(*),«(*)), tf.(z(*oMo) = 0, (2)

This paper is mainly concerned with a class of optimal control problems of systems governed by the nonlinear dynamic systems on time scales. Introducing the reasonable weak solution of nonlinear dynamic systems, the existence of the weak solution for the nonlinear dynamic systems on time scales and its properties are presented. Discussing L1-strong-weak lower semicontinuity of integral functional, we give sufficient conditions for the existence of optimal controls. Using integration by parts formula and Hamiltonian function on time scales, the necessary conditions of optimality are derived respectively. Some examples on continuous optimal control problems, discrete optimal control problems, mathematical programming and variational problems are also presented for demonstration.

In this paper, we consider a class of optimal control problems in which the system is to be determined in an optimal way. This class of problems involves the choice of a fixed number of switching time points which divide the system’s time horizon into a number of time periods. For each of these time periods, a subsystem is selected, from a finite number of given candidate subsystems, to run during that time periods. The choice of the switching points and the selection of the subsystems are carried out in such a way that a given cost functional is minimized. We consider only problems involving ordinary differential equations over a finite time horizon. A computational method is developed for solving these problems. In our method, the candidate subsystems are combined into a single system by considering their ‘linear combination’. By introducing suitable constraints on the coefficients of the linear combination and using a time rescaling technique, the original problem is transformed into an equivalent optimal control problem with system parameters. An algorithm is proposed for solving this transformed problem and the required gradient formulae are derived. To show the effectiveness of the method, a numerical example is solved.

In optimal control theory, it is well known that the costate arc and the associated maximized Hamiltonian function can be interpreted in terms of gradients of the value function, evaluated along the optimal state trajectory. Such relations have been referred to as `sensitivity relations? in the literature. In this paper, we announce new sensitivity relations for state constrained optimal control problems. For the class of optimal control problems considered there is no guarantee that the co-state arc is unique; a key feature of the results is that they assert `some? choice of co-state arc can be made, for which the sensitivity relations are valid. The proof technique is to introduce a new optimal control problem that possesses a richer set of control variables than the original problem. The introduction of the additional control variables in effect enlarges the class of variations with respect to which the state trajectory under consideration is a minimizer; the extra information obtained is precisely the desired set of sensitivity relations.

In this paper, a variational problem is considered with differential equality constraints over a variable interval. It is stressed that the abnormality is a local character of the admissible set; consequently, a definition of regularity related to the constraints characterizing the admissible set is given. Then, for the local minimum necessary conditions, a compact form equivalent to the well-known Euler equation and transversality condition is given. By exploiting this result and the previous definition of regularity, it is proved that nonregularity is a necessary and sufficient condition for an admissible solution to be an abnormal extremal. Then, a necessary and sufficient condition is given for an abnormal extremal to be weakly abnormal. The analysis of the abnormality is completed by considering the particular case of affine constraints over a fixed interval: in this case, the abnormality turns out to have a global character, so that it is possible to define an abnormal problem or a normal problem. The last section is devoted to the study of an optimal control problem characterized by differential constraints corresponding to the dynamics of a controlled process. The above general results are particularized to this problem, yielding a necessary and sufficient condition for an admissible solution to be an abnormal extremal. From this, a previously known result is recovered concerning the linearized system controllability as a sufficient condition to exclude the abnormality.

1 A Survey on Computational Optimal Control.- Issues in the Direct Transcription of Optimal Control Problems to Sparse Nonlinear Programs.- Optimization in Control of Robots.- Large-scale SQP Methods and their Application in Trajectory Optimization.- Solving Optimal Control and Pursuit-Evasion Game Problems of High Complexity.- 2 Theoretical Aspects of Optimal Control and Nonlinear Programming.- Continuation Methods In Boundary Value Problems.- Second Order Optimality Conditions for Singular Extremals.- Synthesis of Adaptive Optimal Controls for Linear Dynamic Systems.- Control Applications of Reduced SQP Methods.- Time Optimal Control of Mechanical Systems.- 3 Algorithms for Optimal Control Calculations.- Second Order Algorithm for Time Optimal Control of a Linear System.- An SQP-type Solution Method for Constrained Discrete-Time Optimal Control Problems.- Numerical Methods for Solving Differential Games, Prospective Applications to Technical Problems.- Construction of the Optimal Feedback Controller for Constrained Optimal Control Problems with Unknown Disturbances.- Repetitive Optimization for Predictive Control of Dynamic Systems under Uncertainty.- Optimal Control of Multistage Systems Described by High-Index Differential-Algebraic Equations.- A New Class of a High Order Interior Point Method for the Solution of Convex Semiinfinite Optimization Problems.- A Structured Interior Point SQP Method for Nonlinear Optimal Control Problems.- 4 Software for Optimal Control Calculations.- Automated Approach for Optimizing Dynamic Systems.- ANDECS: A Computation Environment for Control Applications of Optimization.- Application of Automatic Differentiation to Optimal Control Problems.- OCCAL: A mixed symbolic-numeric Optimal Control CALculator.- 5 Applications of Optimal Control.- A Robotic Satellite with Simplified Design.- Nonlinear Control under Constraints of a Biological System.- An Object-Oriented Approach to Optimally Describe and Specify a SCADA System Applied to a Power Network.- Near-Optimal Flight Trajectories Generated by Neural Networks.- Performance of a Feedback Method with Respect to Changes in the Air-Density during the Ascent of a Two-Stage-To-Orbit Vehicle.- Linear Optimal Control for Reentry Flight.- Steady-State Modelling of Turbine Engine with Controllers.- Shortest Paths for Satellite Mounted Robot Manipulators.- Optimal Control of the Industrial Robot Manutec r3.

This paper introduces a numerical technique for solving a class of optimal control problems containing nonlinear dynamical system and functional of state variables. This numerical method consists of two major parts. In the first part, using linear combination property of intervals, we convert the nonlinear dynamical system into an equivalent linear system. And in the second part, which we are dealing with a linear dynamical system, using Legendre expansions for approximating both the state and associated control together with discretizing the constraints over the Chebyshev-Gauss-Lobatto points, the optimal control problem is transformed into a corresponding NLP problem which is diretly solved. The proposed idea is illustrated by several numerical examples.

In general, optimal control problems rely on numerically rather than analytically solving methods, due to their nonlinearities. The direct method, one of the numerically solving methods, is mainly to transform the optimal control problem into a nonlinear optimization problem with finite dimensions, via discretizing the objective functional and the forced dynamical equations directly. However, in the procedure of the direct method, the classical discretizations of the forced equations will reduce or affect the accuracy of the resulting optimization problem as well as the discrete optimal control. In view of this fact, more accurate and efficient numerical algorithms should be employed to approximate the forced dynamical equations. As verified, the discrete variational difference schemes for forced Birkhoffian systems exhibit excellent numerical behaviors in terms of high accuracy, long-time stability and precise energy prediction. Thus, the forced dynamical equations in optimal control problems, after being represented as forced Birkhoffian equations, can be discretized according to the discrete variational difference schemes for forced Birkhoffian systems. Compared with the method of employing traditional difference schemes to discretize the forced dynamical equations, this way yields faithful nonlinear optimization problems and consequently gives accurate and efficient discrete optimal control. Subsequently, in the paper we are to apply the proposed method of numerically solving optimal control problems to the rendezvous and docking problem of spacecrafts. First, we make a reasonable simplification, i.e., the rendezvous and docking process of two spacecrafts is reduced to the problem of optimally transferring the chaser spacecraft with a continuously acting force from one circular orbit around the Earth to another one. During this transfer, the goal is to minimize the control effort. Second, the dynamical equations of the chaser spacecraft are represented as the form of the forced Birkhoffian equation. Then in this case, the discrete variational difference scheme for forced Birkhoffian system can be employed to discretize the chaser spacecraft's equations of motion. With further discretizing the control effort and the boundary conditions, the resulting nonlinear optimization problem is obtained. Finally, the optimization problem is solved directly by the nonlinear programming method and then the discrete optimal control is achieved. The obtained optimal control is efficient enough to realize the rendezvous and docking process, even though it is only an approximation of the continuous one. Simulation results fully verify the efficiency of the proposed method for numerically solving optimal control problems, if the fact that the time step is chosen to be very large to limit the dimension of the optimization problem is noted.

In the paper, the method of straight lines approximately solves one class of optimal control problems for systems, the behavior of which is described by a nonlinear equation of parabolic type and a set of ordinary differential equations. Control is carried out using distributed and lumped parameters. Distributed control is included in the partial differential equation, and lumped controls are contained both in the boundary conditions and in the right-hand side of the ordinary differential equation. The convergence of the solutions of the approximating boundary value problem to the solution of the original one is proved when the step of the grid of straight lines tends to zero, and on the basis of this fact, the convergence of the approximate solution of the approximating optimal problem with respect to the functional is established. A constructive scheme for constructing an optimal control by a minimizing sequence of controls is proposed. The control of the process in the approximate solution of a class of optimization problems is carried out on the basis of the Pontryagin maximum principle using the method of straight lines. For the numerical solution of the problem, a gradient projection scheme with a special choice of step is used, this gives a converging sequence in the control space. The numerical solution of one variational problem of the mentioned type related to a one-dimensional heat conduction equation with boundary conditions of the second kind is presented. An inequality-type constraint is imposed on the control function entering the right-hand side of the ordinary differential equation. The numerical results obtained on the basis of the compiled computer program are presented in the form of tables and figures. The described numerical method gives a sufficiently accurate solution in a short time and does not show a tendency to «dispersion». With an increase in the number of iterations, the value of the functional monotonically tends to zero

In this paper we define a class of optimal control problems which we denote “embedded optimal control problems”. These are not true optimal control problems since the control system is not locally controllable on the manifold on which it is defined. Despite this, they allow for a well defined associated optimal control problem which does not admit abnormal extremals. We apply Pontryagin's maximum principle to the embedded optimal control problem to derive the generating differential equations for the normal and abnormal extremals. We show that the normal extremal generating equations in a sense contain the extremal generating equations for the associated optimal control problem. We show that this is not the case for the abnormal extremal generating equations. This has applications to the study of the optimal control of systems constrained to a given submanifold of a configuration space, for example the sphere or hypersphere. We apply the theory to three examples in order to illustrate its applicability and to show how it relates to well known results.

In this paper, an iterative adaptive dynamic programming (ADP) algorithm is developed to solve the optimal cooperative control problems for residential multi-battery systems. To avoid solving high-dimensional optimal control problems, we first constrain all the batteries at their worst performance, which transforms the multi-input optimal control problem into a single-input one. Based on the worst-performance optimal control law, the optimal cooperative control law for the residential multi-battery systems is obtained, where in each iteration, only a single-input optimization problem is implemented. Finally, numerical results are given to illustrate the performance of the developed algorithm.

This article presents a unified approach to simultaneous solution of optimization and optimal control problems in batch distillation, operating under different modes of operation: variable, constant, or optimal reflux. The simplified, computationally efficient short‐cut method and a novel algorithm to solve the optimal control problems in batch distillation is the basis of this unified approach. The short‐cut method identifies the feasible region of operation essential for optimization and optimal control problems, and provides analytical partial derivatives of the model parameters crucial to the solution.The new algorithm for the solution of optimal combination of the maximum principle and NLP optimization techniques. It circumvents the problems associated with the maximum principle approach (iterative solution of a two‐point boundary value problem, undounded control variables, and inability to handle the simultaneous optimization and optimal control problem), and the coupled ODE discretization‐NLP optimization scheme for nonlinear models (higher system nonlinearities, multiplicity of solutions, sensitivity of convergence to initial guesses). This algorithm reduces the dimensionality of the problem, and the nature of the algorithm allows a common platform to optimal solutions of different operating conditions. This article also shows that different categories of the optimal control problems in batch distillation essentially involve the solution of the maximum distillate problem.

In this paper, we consider the numerical solution of a class of optimal control problems involving variable time points in their cost functions. The control enhancing transform is first used to convert the optimal control problem with variable time points into an equivalent optimal control problem with fixed multiple characteristic time (MCT). Using the control parametrization technique, the time horizon is partitioned into several subintervals. Let the partition points also be taken as decision variables. The control functions are approximated by piecewise constant or piecewise linear functions in accordance with these variable partition points. We thus obtain a finite dimensional optimization problem. The control parametrization enhancing control transform (CPET) is again used to convert approximate optimal control problems with variable partition points into equivalent standard optimal control problems with MCT, where the control functions are piecewise constant or piecewise linear functions with pre-fixed partition points. The transformed problems are essentially optimal parameter selection problems with MCT. The gradient formulae for the objective function as well as the constraint functions with respect to relevant decision variables are obtained. Numerical examples are solved using the proposed method.

This paper builds up two equivalence theorems for different kinds of optimal control problems of internally controlled Schrodinger equations. The first one is an equivalence of the minimal norm and the minimal time control problems where the target sets are the origin of the state space. (The minimal time control problems are also called the first type of optimal time control problems.) The second one is an equivalence of three optimal control problems: optimal target control problems, optimal norm control problems, and the second type of optimal time control problems.