Novel Solution for Multi-connectivity 5G-mmW Positioning

This paper analyzes the problem of optimum user association and sum rate maximization for software defined radio access networks (SD-RANs) with access node diversity for fifth generation (5G) wireless networks. We consider four complementary types of access nodes namely, a massive multiple- input multiple-output (MIMO) base station (BS), MIMO BSs, small cells (SCs), and indoor and outdoor distributed antenna systems (DAS). The SDRAN user association problem is solved through a novel three-stage optimization scheme called the place coverage (TPC). TPC divides the user equipment (UEs) into two sets of indoor and outdoor UEs. Initially, TPC associates indoor UEs with the indoor DAS access nodes. Next, outdoor UEs are associated with the outdoor DAS access nodes, SCs, MIMO BSs, and the massive MIMO BS. Finally, the remaining resources of indoor and outdoor access nodes are used to serve the UEs that have not been served. The scope of TPC is multifold. First, TPC reflects the closest model to a real-world diverse 5G network. Secondly, servicing the indoor UEs with iDAS antennas results in lower power load per user for the access network resulting in better coverage, quality, and data speed. Thirdly, TPC provides reduced radiation levels for indoor UEs. Numerical results show that TPC provides significant sum rate and fairness gains over the received signals strength (RSS) based association schemes [1]. Moreover, TPC provides comparable performance levels as the optimum association scheme based on exhaustive search while bringing significant complexity reduction.

Multiple-input multiple-output (MIMO) is considered as the key technology for 5G wireless communications networks. In the millimeter-wave (mmWave) frequency bands, directional beamforming is essential to the establishment of an efficient radio link for signal transmission. However, in wireless mobile environments, the effective beam direction is generally unavailable in the initial access phase. Hence, beam alignment (BA) is crucial for link establishment in initial access. In this work, we propose an efficient BA technique, referred to as the multi-modal pattern BA scheme, to improve the performance and efficiency of initial access in massive MIMO systems. Unlike the conventional sequential search scheme using single-modal patterns, the transmission of synchronization signals in the proposed scheme is based on the use of multi-modal patterns, each of which specifies multiple main lobes with distinguishable directions. Incomparison with the conventional scheme, our scheme can greatly enhance the achieved angular resolution after BA under the use of a fixed number of synchronization signals. As a result, the signal-to-noise ratio (SNR) of the established link is significantly improved. By contrast, if the same angular resolution is desired, the proposed scheme can greatly reduce the number of required synchronization signals to conserve the radio resources, including transmission power and bandwidth, and to decrease the searching delay in the BA procedure. In addition, considering multi-modal pattern construction for the transmission using a single radio-frequency (RF) chain, we propose an effective approach to generate the desired beamforming vectors fulfilling the essential constant amplitude constraint.

Time division duplexing (TDD) is adopted to exploit the uplink and downlink channel reciprocity in most of studies on massive multiple-input multiple-output (MIMO) systems. However, even in TDD, a base station (BS) still requires to transmit downlink training signals, which are named in the 3GPP standard as channel state information reference signals (CSI-RSs), to fully support spatial multiplexing in practice. This is because user equipments (UEs) may deploy less number of transmit antennas than receive antennas due to practical issues. Since uplink sounding reference signals (SRSs) are transmitted from only the transmit antennas of the UE, the BS is not able to obtain full downlink MIMO CSI by using channel reciprocity for spatial multiplexing. Hence, after reception of the downlink CSI-RSs, the UE still needs to feed back quantized CSI using a codebook to support spatial multiplexing. Taking practical antenna structures into account for reducing downlink CSI-RS overhead, this paper proposes possible approaches for downlink MIMO CSI reconstruction at the BS using the SRS with quantized downlink CSI to support spatial multiplexing. Numerical results show that the proposed techniques outperform the conventional one, i.e., solely based on the quantized CSI, in terms of the spectral efficiencies of spatial multiplexing.

Massive multiple-input multiple-output (MIMO) systems, where base stations (BSs) are equipped with hundreds of antennas, are an attractive way to handle the rapid growth of data traffic. As the number of user equipments (UEs) increases, the initial access and handover in contemporary networks will be flooded by user collisions. In this paper, a random access protocol is proposed that resolves collisions and performs timing estimation by simply utilizing the large number of antennas envisioned in massive MIMO networks. UEs entering the network perform spreading in both time and frequency domains, and their timing offsets are estimated at the BS in closed form using a subspace decomposition approach. This information is used to compute channel estimates that are subsequently employed by the BS to communicate with the detected UEs. The favorable propagation conditions of massive MIMO suppress interference among UEs, whereas the inherent timing misalignments improve the detection capabilities of the protocol. Numerical results are used to validate the performance of the proposed procedure in massive MIMO networks, under uncorrelated and correlated fading channels. With $2.5 \times 10^{3}$ UEs that may simultaneously become active with probability 1%, a total of 16 frequency–time codes, and 100 antennas, a given UE is detected with probability 75%, and the accuracy of its timing estimate is on the order of few samples.

We address the problem of analyzing and classifying into groups the downlink channel environment in a dense millimeter-wavelength cell, accounting for path loss, multipath fading, and User Equipment (UE) blocking, by employing a hybrid propagation and multipath fading model, thus using accurate inter-group interference modeling. The base station (BS) employs a large Uniform Planar Array (UPA) to facilitate massive Multiple-Input, Multiple-Output (MIMO) communications with high efficiency. UEs are equipped with a single antenna and are distributed uniformly within the cell. The key problem is analyzing and defining groups toward efficient precoding. Because balanced throughput is desired between groups, up to four separate frequency sub-carriers are employed in an Orthogonal Frequency Division Multiple Access (OFDMA) system. We show that by employing three or four OFDMA subcarriers, depending on the number of UEs in the cell and the cell range, the UEs can be efficiently separated into <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">high-throughput</i> groups, with each group employing Virtual Channel Model Beams (VCMB) based inner precoding, followed by efficient Multi-User Multiple-Input Multiple-Output (MU-MIMO) outer precoders. For each group, we study two different sub-grouping methods offering different advantages. We show that the improvement offered by Zero-Forcing Per-Group Precoding (ZF-PGP) over Matched Filter Precoding (MFP) and Zero-Forcing Precoding (ZFP) is very high when finite-alphabet inputs are used. We also show ZF-PGP with finite-alphabet inputs significantly outperforms MFP with Gaussian inputs in certain realistic setups. Finally, a new technique for power allocation among different UEs is proposed, called Optimized Per-Group Power Allocation (OPGPA), which achieves much higher power efficiency jointly with equal throughput among all UEs in each group.

Accurate channel state information (CSI) at base station (BS) is the key to achieve full multiplexing and diversity gain in traditional multiple-input multiple-output (MIMO) systems. In frequency-division-duplex (FDD) systems, it is obtained through downlink training and uplink feedback. However, the training and feedback overhead in massive MIMO systems is unacceptable for the large number of antennas equipped at BS. To reduce the CSI feedback overhead and improve CSI quantization accuracy, we propose a limited feedback scheme for spatio-temporal correlated massive MIMO channel. The proposed scheme jointly performs Karhunen-Loève transform (KLT) and polar-cap quantization on CSI. For the compactly deployed antennas at BS, there exists spatial correlation in massive MIMO channel. When the user equipment (UE) moves slowly, adjacent channels feature temporal correlation. The high dimensional and spatial correlated CSI is compressed through KLT. Then the compressed CSI is normalized to be isotropic to perform polar-cap quantization. Simulation results show that the proposed scheme is capable of improving the sum-rate performance with limited feedback bits for massive MIMO systems.

With the improvement of mobile communication technologies and their broad applications, mobile communication will have more impact on our life. Such systems will support a variety of personal communication services with high-data rate and very low latency applications. To achieve such demands, many proposals associated with the development of 5G identify a set of requirements for which different technological directions are independently emerging. One direction is utilizing the millimeter-wave (mm-Wave) frequency bands where more spectrums are available. Millimeter-wave frequencies offer the advantage of physically smaller components that results in cost-effective RF transceivers and feasible large-scale integrated phased arrays. The smart RF transceivers of 5G along with the potential high-frequency innovative designs must satisfy the growing consumer and technology requirements. This implies utilizing the state-of-the-art guiding structures, especially printed ridge gap waveguide (PRGW), that have low loss and minimal dispersion compared with traditional PCB-based structures. The present chapter focuses on the necessary components for a beamforming antenna system which is implemented using PRGW technology. Millimeter wave antennas with different polarizations have been addressed. Power combining and dividing components have been also developed. These components have been used for integration in a complete beamforming antenna system working at an mm-Wave frequency band.

This paper presents a down-conversion Gilbert Cell mixer design operating in the 28 GHz millimeter-wave (mmWave) frequency band in 5G applications. The current bleeding technique is used to increase the conversion gain (CG) in the down-conversion mixer circuit, which leads to high linearity (IIP3) and low noise Figure (NF) performance. An intermediate frequency (IF) buffer has been coupled to the mixer outputs to improve linearity performance and facilitate impedance matching. The proposed mixer circuit is designed using a commercial 40 nm low-power CMOS technology. The mixer core and the IF buffer draw 43.61 mA from a 1.1 V supply voltage. According to post-layout simulation results, the mixer performs with a conversion gain of −2.32 dB, a noise Figure of 9.482 dB, and IIP3 of 12.667 dBm in the 28 GHz millimeter-Wave (mmWave) frequency band, including the current bleeding structure and the output buffers. Finally, high isolation between ports has been established, with LO-RF isolation below −50 dB, LO-IF isolation below −40 dB, and RF-IF isolation below −40 dB.

The base station (BS) density influences the coverage performance of cellular communication system. In massive multiple input multiple output (MIMO) system, each BS is equipped with large scale antenna array. The stochastic geometric model is employed because of its analytical tractability. This paper demonstrates that BS density has to be below a certain bound in order to satisfy the coverage requirement in massive MIMO system. Closed-form expression for the BS density bounded by maximum outage probability is derived using Lambert W function. Moreover, the expression for the upper bound of successful area spectral efficiency (ASE) is also derived. Our study claims that increasing BS density will lead to the deterioration of coverage performance in massive MIMO system.

In a massive multiple-input multiple-output (MIMO) system, channel state information (CSI) is essential for the base station (BS) to achieve high performance gain. The user equipment (UE) needs to estimate CSI and then feeds it back to the BS in the frequency division duplexing (FDD) mode. Effective compression of CSI will significantly reduce the cost of channel feedback, and many deep learning (DL) based channel compression schemes have been proposed to achieve this goal. In this paper, rather than viewing CSI as images as in most existing works, we propose a new perspective of viewing CSI as an information sequence and analogize CSI feedback to a machine translation task. Further, we propose a novel sequence to sequence (Seq2Seq) model for CSI feedback composed of only recurrent neural networks and a small-scale fully connected layer, avoiding the convolution and pooling structure commonly used in current DL-based works. The advantage of this scheme is that it fully integrates the physical characteristics of the MIMO channel in the spatial domain into the structure of the neural network and avoids the loss of some prominent unsmooth or discontinuous features caused by the inappropriate convolution and pooling operation. Simulation results show that the proposed Seq2Seq model outperforms other DL-based CSI compression techniques under various communication scenarios.

The use of massive multiple-input multiple-output (MIMO) to serve a crowd of\nuser equipments (UEs) is challenged by the deficit of pilots. Assuming that the\nUEs are intermittently active, this problem can be addressed by a shared access\nto the pilots and a suitable random access (RA) protocol. The strongest-user\ncollision resolution (SUCRe) is a previously proposed RA protocol that often\nprivileges the UEs closer to the base station (BS). In contrast, we propose a\nnovel RA protocol using a decentralized pilot power allocation method that aims\nat a fairer performance. The proposed access class barring with power control\n(ACBPC) protocol allows each UE to estimate, without additional overhead, how\nmany UEs collided for the chosen pilot and calculate an ACB factor, which is\nthen used to determine the pilot retransmission probability in the next\nprotocol step. The results show that the proposed ACBPC protocol is superior to\nSUCRe in terms of providing a fair connectivity for very crowded networks,\nalthough still being distributed and uncoordinated as the original SUCRe\nprotocol.\n

This paper focuses on the uplink (UL) of a single-cell massive multiple-input multiple-output (MIMO) systems in which the base station (BS) equipped with M antennas communicates with K single-antenna user equipments (UEs). Due to the finer spatial resolution achieved by a huge number of antennas at the base stations, these systems can substantially reduce intra-cell interference with simple signal processing. However, most precoding schemes exhibit prohibitively high computation complexity as the system dimensions increase. For example, the near-optimal minimum mean squared error (MMSE) precoding requires the inversion of a large matrix. To reduce further the complexity, the truncated polynomial expansion (TPE) is applied to approximate the inverse of large matrices that appear on the expressions of the optimal linear transceivers. A key requirement to achieve good detection performance is to find good polynomial coefficients (J), where the polynomial coefficients (J) are optimized to maximize the system performance. The simulation results show that the proposed scheme provides very close to optimal performance while reducing significantly the computational complexity.

We address the problem of analyzing and classifying in groups the downlink channel environment in a millimeter- wavelength cell, accounting for path loss, multipath fading, and User Equipment (UE) blocking, by employing a hybrid propagation and multipath fading model, thus using accurate inter-group interference modeling. The base station (BS) employs a large Uniform Planar Array (UPA) to facilitate massive Multiple-Input, Multiple-Output (MIMO) communications with high efficiency. UEs are equipped with a single antenna and are distributed uniformly within the cell. The key problem is analyzing and defining groups toward precoding. Because equitable throughput is desired between groups, Combined Frequency and Spatial Division and Multiplexing (CFSDM) is found to be necessary. We show that by employing three subcarrier frequencies, the UEs can be efficiently separated into high throughput groups, with each group employing Virtual Channel Model Beams (VCMB) based inner precoding, followed by efficient Multi-User MultipleInput Multiple-Output (MU-MIMO) outer precoders. For each group, we study three different sub-grouping methods offering different advantages. We show that the improvement offered by Zero-Forcing Per-Group Precoding (ZF-PGP) over Zero-Forcing Precoding (ZFP) is very high.

This paper considers the problem of massive multiple-input-multiple-output (MIMO) wireless communication systems with quasi-orthogonal space-time block code (QOSTBC) transmission in the presence of spatial correlation effect (SCE) and mutual coupling effect (MCE). Conventional MIMO channels with QOSTBC transmission suffer from several drawbacks. The number of transmit antennas is restricted to a few in order to achieve full transmission rate. Therefore, it is difficult to make a quasi-orthogonal space time block coded massive MIMO system to achieve full transmission rate. Moreover, MIMO channel with QOSTBC transmission is usually considered for the case where the number of user equipments (UEs) is one. We present a joint beamforming and spatial precoding method to deal with the above drawbacks. The proposed method incorporates a beamforming scheme and spatial precoding to formulate an appropriate optimization process to effectively alleviate the considered problems. The resulting optimization problem will be solved by using a cooperative coevolutionary particle swarm optimization algorithm under two proposed fitness functions. During the optimization process, the proposed method finds the optimal beamforming coefficients of the precoding matrix, the optimal normalized positions of transmit and receive antenna elements for the case of using linear antenna arrays, and the optimal angle differences of transmit and receive antenna elements for the case of using circular arrays. Based on the proposed method, we are able to cure the performance degradation of a quasi-orthogonal space time block coded massive MIMO system due to the SCE and MCE. Moreover, the proposed method makes QOSTBC MIMO communications with full transmission rate for any number of transmit antennas achievable. Several simulation examples are presented to show the superior bit error rate (BER) performances of QOSTBC wireless MIMO scenarios with linear as well as circular antenna arrays by using the proposed method as compared to the existing methods.

As a combination of spatial modulation (SM) system and massive multiple-input multiple-output (MIMO) system, massive SM aided MIMO (SM-MIMO) system is recently proposed. In broadband scenarios, single-carrier (SC) modulation is introduced to massive SM-MIMO system, thus massive SC-SM MIMO system is proposed for uplink multi-user transmission over frequency-selective fading channels. In this study, the uplink spectral efficiency (SE) of multi-cell massive SC-SM MIMO system is analysed, meanwhile the pilot contamination effect is taken into consideration. A tight SE lower bound of multi-cell massive SC-SM MIMO system is proposed with maximum ratio (MR) combining, which also takes into account the imperfect channel estimation, transmit antenna correlation and path loss. The tightness of the authors' proposed closed-form SE lower bound is shown via simulation results. The optimal pilot reuse factor can be determined with different system configurations by simulations, and the pilot reuse factor that is larger than one is more suitable for less TAs and user equipments.