On Power Line Positioning Systems

The paper presents a methodology proposal for testing and evaluation of communication systems in Smart Grids, especially for Power Line Communication (PLC) systems. The PLC technology is widely used in power grid as a part of Advanced Metering Infrastructure (AMI) allowing mainly data transfers between a management system at utility and customer-premises smart meters. However, the PLC technology on medium voltage (MV) lines is often used for remote control and monitoring of distribution transformers as well. Since power grid and consequently power lines have different transmission parameters affected by their placement and potentially burdened by interferences, the PLC systems have to be evaluated on site before placed to production. In this paper, authors propose a methodology for long-term benchmarking of the PLC systems using newly developed testing tools. The methodology is subsequently tested on real power grid and a selection of results is presented.

The emissions from the power line communication (PLC) system should be investigated for the influence to the electromagnetic environment. The method of moment (MOM) has been studied to estimate the emitted electric field. However, the MOM is difficult to treat the dielectric material of the cable. This paper proposes the method of creating the wire grid model considering the dielectric material of the power line cable. The radius of the wire was determined from the per unit length inductance of the cable. The admittance is inserted between wires to present the effect of the dielectric material, and the value is determined from the admittance calculated by using the FEM based on the two-dimension model. The other admittance was inserted between each wire and ground and the value was also determined from the FEM results. The appliances were presented by T-type network based on the measurement results. The common mode input impedance and radiated magnetic field were measured and compared with the calculated one, and the evaluation indicated that the well agreement was obtained. A simple model of the indoor power line system was constructed and the radiated magnetic field was calculated. The evaluation was indicated that the calculation results almost agreed with the measured one. These results mean that the wire grid model is effective to estimate the radiated electromagnetic field from PLC system.

Power line communication (PLC) utilizes power lines for the purpose of electronic data transmission. The performance of a PLC system is significantly affected by the additive and multiplicative power line noises; the additive noises are of two types, namely background noise and impulsive noise. Whereas, the multiplicative PLC noise leads to fading in the received signal strength. In this paper, we evaluate the performance of a PLC system over log-normal fading channel under Nakagami-m distributed additive background noise assuming binary phase shift keying modulation scheme. The analysis involving log-normal fading is very complicated. Hence we use a novel gamma approximation to log-normal distribution for our analysis. We evaluate the probability density function of the decision variable. A closed-form expression of the analytical average bit error rate of the considered system is derived. We also compute the diversity order of the considered PLC system. The validity of the derived analytical expressions is closely verified by the simulation results.

Although Power Line Communication (PLC) is not a new technology, its use to support data transmission over low voltage (LV) distribution networks is still the focus of ongoing research. This thesis focuses on the channel modelling and performance evaluation of narrowband (NB) PLC system. First, the channel modelling approaches of PLC are studied. Then, the proposed PLC channel modelling method based on the bottom-up approach for LV narrowband PLC in a frequency band between 9 kHz and 490 kHz is presented. This proposed model employs the transmission and scattering matrix methods to calculate the transfer function of a typical LV PLC network which comprises two common cable types (copper cables and aluminium conductor steel reinforced). Unlike the top-down approaches, this model is scalable as the network complexity increases and can better describe the network behaviour as a function of physical parameters.In addition, the noise characteristics and popular noise reduction techniques of PLC are studied. The major impairment to the PLC is the impulsive noise which is mainly generated by the switching transient in the network. Hence, a new technique is proposed to mitigate the impact of impulsive noise on data transmission over power lines. This proposed technique is an optimal Clipping/Blanking nonlinearity technique which is based on the minimum bit error rate (BER) search. Results obtained from the simulation of this technique demonstrate that performance has been enhanced in the NB-PLC system. The performance of the narrowband PLC system is also evaluated in both physical (PHY) and medium access control (MAC) layers. Since Orthogonal Frequency Division Multiplexing (OFDM) is a suitable modulation scheme for hostile environment of the power line, it is used to evaluate the PHY layer performance. As a result of the PHY layer performance analyses, it is found that the BER performance between neighbouring points in the typical LV PLC network is reasonable, but communication beyond one hop have to rely on upper layer protocols. In the MAC layer performance evaluation of the PLC system, the widely known random access MAC protocol that uses the Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) will be utilised. The MAC performance evaluation of the PLC system demonstrates a significant packet loss in LV PLC network even with a light traffic condition due to the noisy channel. Furthermore, the goodput declines abruptly once the individual transmission rate is high enough to block the network. In addition, the simulation results show that the channel errors can be reduced by adjusting the MAC parameters to allow the re-transmissions mechanisms to recoup the lost packets.

The nature of the Power Line Communication (PLC) equipment is complex because it is considered as an information equipment for Electro-Magnetic Compatibility (EMC) standardization, but it is used to inject High-Frequency (HF) and Very High Frequency (VHF) frequency signals on the existing power network which is not designed to guide these frequencies. This PLC system issue leads to some difficulty to finalize EMC standardization of PLC equipment. This paper shows some EMC issues due to the parasitic radiation of HF and VHF PLC systems. An original method using radiofrequency analysis is used to demonstrate that power lines act as antennas for PLC frequencies, as if the PLC system was a radiofrequency system. So, we can define the PLC system as a "not intended radiofrequency system", i.e. a family product which have to comply not only with EMC standards but also with Radio Equipment Directive (RED) system.

The use of repeaters (relays) has recently been introduced in power line communication (PLC) systems for long-distance data transfer and thus, it becomes important to analyze the performance of relay based PLC systems. A simplified system model with distance dependent signal attenuation and additive white Gaussian noise may not cover all the factors affecting the data transfer, such as variation in amplitude (fading) and occurrence of impulsive noise. Hence, a more realistic system model with log-normal fading, distance dependent signal attenuation, and a Bernoulli-Gaussian impulsive noise is considered in this paper to study the end-to-end average bit error rate (BER) and the end-to-end average channel capacity of a PLC system equipped with amplify-and-forward (AF) relays. Approximate closed-form expressions of the end-to-end average BER for binary phase-shift keying and the average channel capacity for high signal-to-noise ratio are obtained. The performance of the PLC system with AF relays is found to be superior compared to that of a direct transmission PLC system for fixed transmission power.

The paper presents a single-input-multiple-output-based power line communication (PLC) system employing <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${M}$ </tex-math></inline-formula> -ary phase-shift keying signaling for data transmission, with the channels subjected to correlated Rayleigh multipath channels and corrupted by Nakagami- <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${m}$ </tex-math></inline-formula> noise environment. The channel state information for the PLC system is obtained prior to data transmission using the minimum mean square error estimation technique, utilizing which a maximum likelihood-based sub-optimal receiver is proposed. The closed-form expression for the symbol error probability (SEP) is derived, for the cases of the channels following exponential and uniform correlations, using a characteristic function approach. Furthermore, the optimal pilot symbol duration is obtained to maximize the normalized error-free data rate of the system, which simultaneously saves on the energy of the pilot symbols and reduces the SEP of the data symbols. The numerical results demonstrate the effect of variation of different system parameters such as signal-to-noise ratio, channel diversity, pilot symbol quality, correlation factor, and the noise shape parameter <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${m}$ </tex-math></inline-formula> of the background noise on the maximum normalized error-free data rate and thereby providing various insights into the system design for a reliable and energy-efficient PLC system with imperfect knowledge of the channels at the receiver.

Modern hospitals are beginning to adopt E-HEALTH as efficient complements to the traditional healthcare services. To support the E-HEALTH services, a locatable, radiation-free and high-capacity communication system is urgently needed in hospitals. Power line communication (PLC) system can use the ubiquitous power line network to power the light-emitting diode (LED) lights while serving as the backbone network for the indoor visible light communication (VLC) systems naturally. In this paper, an integrated broadband power line and visible light communication systems with OFDM modulation is proposed for the indoor hospital applications. This gives a brand-new solution to replace the conventional wireless communication systems in hospitals.

This paper presents Discrete Wavelet Transformed Sparse Code Multiple Access (DWT-SCMA) in Power Line Communication (PLC) systems. In the present internet of things era, PLC provides an established infrastructure for low-cost and reliable indoor connectivity. PLC systems can benefit from the Sparse Code Multiple Access (SCMA) technique, which allows multiple users to access a frequency slot simultaneously to maximize spectrum efficiency. However, interuser interference arises in SCMA when numerous users map their data to the same frequency resource; this, in turn, is likely to be enhanced by the noisy PLC channel. This article adopts the intriguing aspects of DWT to address the interference difficulties. A mathematical model of the proposed technique is also presented and compared with Fast Fourier Transformed SCMA (FFT-SCMA). In the PLC environment, DWT-SCMA is found to outperform FFT-SCMA.

HF Band Power Line Communication (PLC) is rapidly gaining popularity with new network systems not only in the home, but also in places where the number of users is relatively large. Since the PLC uses wide frequency band for data modulation, some coexistence conditions with other services were provided. We investigated the performance of three types of PLC systems, HD-PLC, HomePlug and UPA, under unfavorable conditions such as connecting the PLC modem to the uninterruptible power supply (UPS) outlet or simultaneously using it with a different PLC system. Although violating the proper instructions, each PLC system could still transfer data to some degrees. It was confirmed that UPS and PLC act as a source of noise for the other PLC systems and the degree of interference varies with the PLC systems used.

In recent times, power line communication (PLC) has an ability of communicating the signals and messages making use of the existing power lines without going for new mediums such as optical fibers or radio waves. Considering the voltage, electrical networks are rated as low (1 kV), medium (1–100 kV), and high (>100 kV) networks and the communication problems in these networks increase with increase in voltage. In order to establish high-speed data communications with data rates in the range of megabit/s over power line networks, dedicated communication systems considering the hostile channel properties are required. In addition to signal distortion, losses in cables and multipath propagation, noise from the system also plays a key role to alter the digital communication over power line networks which is dealt in this project. In this work, the signals are obtained with less bit error rate (BER) using Rayleigh fading channel improving the efficiency of the whole system. Different modulation techniques are compared in narrowband power line communication (PLC) systems, and some suggestions are made for the improvement of data transmission in narrowband systems. The best compromise for single-carrier PLC modules between efficiency and architecture complexity is being investigated in this project.

Power Line Communication (PLC) is an innovative system for carrying data through power line without conventional local area network cables. However, in hospitals the data signal from PLC system superimposed on the alternating power current possibly results in a power noise for medical equipments and thereby inducing hazardous malfunction of medical equipments. The purpose of this study was to investigate the effects of the PLC on medical equipments. We used three different types of PLC modems and their communication systems: HomePlug system, Universal Powerline Association (UPA) system and High Definition (HD)-PLC system. The frequency band of the data signal was 2~30 MHz. We investigated the effect of the data signal from PLC system superimposed on the alternating power current and voltage, and we also investigated the effect of the electromagnetic wave radiated from the power line of PLC modem on medical equipments. We evaluated thirty kinds of medical equipments, such as ventilators, telemeters, infusion pumps and so on. Malfunction did not occur in any medical equipment investigated by the data signal superimposed on the alternating power current. Although malfunction did occur in ultrasonic diagnostic equipment and external cardiac pacemaker when the power line was moved closer toward the medical equipments, the malfunction occurred in the distance less than 2 cm. In conclusion the effect of PLC on medical equipment investigated in this study was considered to be minor.KeywordsPower Line Communicationmedical equipmentpower noiseelectromagnetic wave

The power-line communication (PLC) technique involves sending information through an electrical conductor for a commercial or domestic purpose. Lately, electronic means of communication have gained popularity for the transfer of information. Conversely, there is an increased requirement for more transmission media, like the use of power line as a communication channel for remote data delivery. This paper focuses on determining the data rate profile achievable using the single-carrier/multicarrier modulation techniques with Reed- Solomon concatenated convolutional (RS-CC) codes for data transmission through a power line channel. In this investigation, MATLAB/SIMULINK was used to explore a low-voltage power line as a communication channel for high data transmission rate. Data transmission was accomplished by utilizing a parametric model of a power line channel with the different kinds of noise considered in the simulation. In the designed power-line communication (PLC) system, single-carrier modulation offered a maximum of 14.4 Mbps reduction in the data rate when the uncoded 64-quadrature amplitude modulation (QAM) was compared to coded 64-QAM with 1/2 forward error correction (FEC). In the OFDM power-line communication (PLC) system, the decrease in the data rate was maximal at 39 Mbps when the uncoded 16-QAM was contrasted with the 16-QAM having 1/2 FEC. It was evident that the increased code rate of the PLC system using single-carrier and OFDM modulation implied increased data rate profiles

This paper introduces the Priority‐Aware Federated Resource Allocation (PAFRA) algorithm, a novel resource allocation strategy designed for power line communication (PLC) systems. Leveraging a federated learning framework, PAFRA optimizes the distribution of limited spectrum resources across multiple nodes within a residential environment. The algorithm integrates a priority‐based time slot allocation to effectively manage subchannel conflicts and employs a Double Deep Q‐Network for local training at each node. This training modality includes comprehensive state, action, and reward configurations to fine‐tune transmission power and subchannel selections. Extensive simulations reveal that PAFRA substantially enhances system throughput, outperforming both traditional numerical optimization methods and contemporary machine learning approaches. Specifically, at a signal‐to‐noise ratio of 30 dB, PAFRA achieves a system throughput of approximately 950 Mbps, marking a 23% improvement over existing approaches. These findings highlight PAFRA's ability to significantly enhance network efficiency while complying with regulatory emission standards, demonstrating its potential to optimize dynamic PLC systems.

In this study, remote control application of an ultrasonic motor (USM) has been achieved over the power line communication (PLC) system. Fast, practical, affordable and effective operating mode is essential for the USM. This study aimed to develop an original, efficient, effective and economical method. Drive and control of USM control has been succeeded with the developed PLC control system. A two-phase high-frequency inverter, a power line transmitter, and a power line receiver circuits have been designed to drive and control of the ultrasonic motor. Required measurements are acquired from the power line to select the most suitable communication frequency and coupling circuit impedance for the PLC system. For the communication frequency and impedance value measurements the receiver and the transmitter circuits have been designed. The PLC-controlled system has been tested for different operating conditions of the ultrasonic motor. USM control has been accomplished over the existing power line without using extra cables and interfaces for communication. The obtained results show that the PLC-controlled system is practical, reliable, cost-effective, and feasible for the remote control of the USM. This research contributes a new and essential perspective for the PLC-based remote control studies in addition to the USM drive and control strategies.