• Home
  • Search
  • On Solving Parametric Optimization Problem of an End Milling Process for Machining of Al 1070 using MCDM Techniques: A Comparative Analysis
  • Cite Icon17
  • https://doi.org/10.1080/2374068x.2023.2216398Copy DOI Icon

On Solving Parametric Optimization Problem of an End Milling Process for Machining of Al 1070 using MCDM Techniques: A Comparative Analysis

Show More
  • Abstract
  • Literature Map
  • References
  • Citations
  • Similar Papers
Abstract

ABSTRACT Determining the optimal intermix of various input parameters for an end milling process is an important task to explore its fullest performance along with the achievement of the desired responses. Several multi-criteria decision-making techniques, like technique for order preference by similarity to ideal solution (TOPSIS), grey relational analysis and multiobjective optimisation on the basis of ratio analysis (MOORA), have been applied for solving parametric optimisation problems of milling processes while assigning equal importance to the considered responses. In this paper, the optimal combinations of cutting speed, feed rate and depth of cut of an end milling process during the machining of Al 1070 alloy are determined using the weighted sum model (WSM), weighted product model (WPM), weighted aggregated sum product assessment (WASPAS), MOORA, TOPSIS, evaluation based on distance from average solution (EDAS), additive ratio assessment (ARAS) and complex proportional assessment (COPRAS) methods with the allocation of unequal weights to the responses determined by standard deviation and entropy techniques. The derived solutions are also compared when the same importance is assigned to the responses. From the results, a parametric combination of 255 rpm cutting speed, 82 mm/min feed rate and 0.75 depth of cut is identified by WSM, WPM, WASPAS, COPRAS, TOPSIS and ARAS methods to achieve the optimal values of material removal rate (MRR) and average surface roughness (Ra) as 595.23 mm3/min and 13.79 µm, respectively. It is also noticed that both feed rate and depth of cut significantly influence MRR and Ra during the machining of Al 1070 alloy.

Similar Papers
  • Research Article
  • Citations106

Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91

  • Oct 01, 2022
  • Journal of Magnesium and Alloys
  • M Varatharajulu +4
  • Research Article
  • Citations10

EVALUATION OF MASS TRANSFER EVAPOTRANSPIRATION MODELS UNDER SEMIARID CONDITIONS USING MCDM APPROACH

  • Jan 01, 2020
  • Applied Ecology and Environmental Research
  • S Islam +5
  • Research Article
  • Citations14

Evaluation of entropy-coupled multi-criteria decision-making methods for enhancing machinability

  • Sep 21, 2024
  • Heliyon
  • Nafisa Anzum Sristi +2
  • Research Article
  • Citations25

Determining the appropriate location for renewable hydrogen development using multi‐criteria decision‐making approaches

  • Dec 06, 2021
  • International Journal of Energy Research
  • Khalid Almutairi
  • Research Article
  • Citations1

Assessment of Hand Hygienic Materials for Nursing Staff at Hospitals with WASPAS Technique and Picture Fuzzy Information

  • Jan 01, 2024
  • IEEE Access
  • Liu Tengfei +7
  • Research Article

Material Selection for Metal Additive Manufacturing Using Multi-Criteria Decision Making Methods

  • Oct 26, 2024
  • International Journal of Engineering and Innovative Research
  • Batuhan Özakın +1
  • Research Article
  • Citations39

Erosion susceptibility mapping of sub-watersheds for management prioritization using MCDM-based ensemble approach

  • Jan 01, 2021
  • Arabian Journal of Geosciences
  • Biman Ghosh +1
  • Research Article
  • Citations28

A comparison of TOPSIS, grey relational analysis and COPRAS methods for machine selection problem in the food industry of Turkey

  • Jul 28, 2021
  • International Journal of Production Management and Engineering
  • Sami Özcan +1
  • Research Article
  • Citations14

Machinery/Service system Scheduled Replacement time determination: A combine Weighted Aggregated Sum Product Assessment, Additive Ratio Assessment and Age Replacement Model approach

  • Apr 22, 2018
  • International Journal of Integrated Engineering
  • Ikuobase Emovon +1
  • Research Article
  • Citations56

Revisiting ranking accuracy within WASPAS method

  • Jul 08, 2019
  • Kybernetes
  • Adil Baykasoğlu +1
  • PDF
  • Research Article
  • Citations50

A Decision-Making Model Based on TOPSIS, WASPAS, and MULTIMOORA Methods for University Location Selection Problem

  • Jul 01, 2021
  • Sage Open
  • Pınar Miç +1
  • Research Article
  • Citations67

Human risk assessment of Panchet Dam in India using TOPSIS and WASPAS Multi-Criteria Decision-Making (MCDM) methods

  • Jun 01, 2019
  • Heliyon
  • Sumanta Bid +1
  • Research Article

Implementation of the WASPAS Method for Selecting an Optimal Project Leader

  • Dec 10, 2025
  • bit-Tech
  • Erwin Erdiyanto +2
  • Research Article
  • Citations22

Multi-criteria decision-making techniques for groundwater potentiality mapping in arid regions: A case study of Wadi Yiba, Kingdom of Saudi Arabia

  • Jun 03, 2024
  • Groundwater for Sustainable Development
  • Nuaman Ejaz +7
  • Research Article
  • Citations148

Multi-criteria ranking of energy generation scenarios with Monte Carlo simulation

  • Nov 10, 2016
  • Applied Energy
  • Tomas Baležentis +1
Cactus Communications logo

Copyright 2026 Cactus Communications. All rights reserved.