Optical fibre pressure and temperature sensor system designed for urodynamic applications

Urodynamic analysis is the predominant method for evaluating dysfunctions in the lower urinary tract. The exam measures the pressure during the filling and voiding process of the bladder and is mainly interested in the contraction of the bladder muscles. The data arising out of these pressure measurements enables the urologist to arrive at a precise diagnosis and prescribe an adequate treatment. A technique based on two optical fiber pressure and temperature sensors with a resolution of better than 0.1 cm H₂O (∼10 Pa), a stability better than 1 cm H₂O/hour, and a diameter of 0.2 mm in a miniature catheter with a diameter of only 5 Fr (1.67 mm), was used. This technique was tested in vivo on four patients with a real-time urodynamic measurement system. The optical system presented showed a very good correlation to two commercially available medical reference sensors. Furthermore, the optical urodynamic system demonstrated a higher dynamic and better sensitivity to detect small obstructions than both pre-existing medical systems currently in use in the urodynamic field.

Ultra-long and large-diameter underwater bored piles are widely used in deep-water bridge foundations; however, key construction parameters such as concrete surface elevation and tremie conduit embedment depth are still largely measured manually, resulting in low levels of automation and limited data traceability. Accurate monitoring of these parameters is essential to ensure construction quality and prevent defects such as pile breakage or mud inclusion. This study aims to develop an intelligent monitoring system to achieve real-time and automated measurement of concrete pouring height and conduit embedment depth during underwater pile construction. An integrated intelligent sensing system was developed combining fiber Bragg grating (FBG) pressure sensors, distributed fiber optic temperature sensing (DTS), RFID-based conduit counting, and a PLC-controlled automated monitoring device. Laboratory experiments and field tests were conducted to evaluate the feasibility of fiber optic pressure and temperature sensing for detecting the concrete interface. Laboratory tests demonstrated that fiber optic pressure and temperature sensors can effectively identify the interface between mud, laitance, and concrete during pouring. Field experiments showed that concrete level monitoring based on intelligent sensing achieved an error ranging from 0.25 m to 0.5 m, while dynamic tracking of the concrete surface achieved accuracy within approximately 0.3 m. The system was successfully applied in the Hangzhou Bay Cross-Sea Bridge project, confirming its reliability in engineering practice. The proposed monitoring system significantly improves the automation and informatization of underwater bored pile construction. Compared with traditional manual sounding methods, it provides higher monitoring frequency, improved accuracy, and real-time data transmission through a cloud platform, enabling traceable management of concealed works. The system offers a practical and cost-effective solution for intelligent construction of deep foundations and supports the digital transformation of pile foundation engineering.

We present in this paper an optical fiber pressure and temperature sensor (OFPTS) with multi Fibre Bragg Grating (FBG) array. The sensor based on an extrinsic Fabry Perot interferometer and is fabricated from silica glass. A femtosecond laser (FSL) was used to inscribe multiple FBGs proximately close to the diaphragm, parallel to each other. This concepts allows a chain of FBGs with miniature active length which can be a significant important tool for medical application, like radio frequency ablation (RFA) cancer treatment.

A pressure and temperature sensor for downhole application is reported. Experiments show the sensor has sensitivity of 0.99μm/MPa and accuracy of 0.1%F.S. for pressure measurement. The sensor is successfully used for downhole 24-hours monitoring.

Fiber Optic Pressure and Temperature Sensors for Gen IV Reactor Environments

A miniature high temperature, high frequency, fiber optic pressure sensor capable of operation above 1000K and frequencies above 1MHz has been developed and tested. The sensor accuracy, pressure resolution, temporal resolution and high temperature capability were first demonstrated through a series of laboratory experiments. The sensors were then tested on the forebody and inside the combustor of a full-scale X-51 configuration at fully duplicated flight conditions in the LENS II reflected shock tunnel at the CUBRC facility in Buffalo, NY. The pressure sensors displayed good run-torun repeatability and durability during the 10 run test program. Forebody and tar combustor pressure measurements respectively displayed a ω -0.8 and ω -1 decay in the power spectrum for frequencies related to fluctuations within the log layer. At low frequency, the spectra were essentially flat. In the combustor, a significant increase in the power-law decay was observed for combusting runs. On the forebody, good spectral agreement was obtained at moderate frequencies between the fiber optic and Kulite piezoresistive pressure sensors. This sensing technology enables improved measurement capabilities during ground testing where high frequency pressure measurements in high temperature high speed flows are required.

A prototype single-mode fibre-based Fizeau interferometric medical pressure and temperature sensor system using coherence reading signal recovery is demonstrated. These sensors have been designed in such a way that they have similar optical path differences and hence problems associated with multiplexing are greatly reduced. For the pressure sensor, a range to resolution ratio of about 6.7*103:1 and an overall measurement accuracy of better than +or-1% over a pressure range of 0-360 mmHg have been achieved. For the temperature sensor, a measurement resolution of 0.006 degrees C and a 1% span linearity over a temperature range of 27.3-62.5 degrees C have been achieved. The performance of both sensors meets or exceeds established medical requirements, and the dimensions of the probes are compatible with commercial electric probes. Hence this new sensor system is expected to be a practical approach for many medical applications.

High sensitivity fiber optic pressure sensor is in great demand in in all aspects due to its advantages. However, the current high sensitivity optical fiber pressure sensor has the problems of large size and high cost. An optical fiber pressure sensor based on all-silica Fabry-Perot interference has been proposed in this paper. The sensor consists of single mode fiber, silica capillary and diaphragm made of coreless optical fiber. The diameter of the sensor is only 125 μm. With precise control of diaphragm thinning, the diaphragm thickness of F-P sensor is only 1.477 μm, the sensor manufactured in this way has sensitivity with 12.586 rad/MPa. The sensor is ease of manufacturing and low cost. Static calibration shown the advantages of the sensor are high sensitivity, good linearity, repeatability, reliability and low hysteresis.

This paper presents an integrated microcavity optical fiber pressure sensor using exfoliated ultrathin graphene atomic layers as a reflective surface to form a Fabry–Perot (F-P) interferometric structure. The fabrication was based on the focused-ion-beam (FIB) micromachining and dry exfoliated graphene transfer method, where the sensor was fabricated directly on a facet of a standard SMF-28 single-mode fiber with the core diameter of $8~\mu \mathrm {m}$ and the cladding diameter of $125~\mu \text{m}$ . The air leakage from the cavity was negligibly small during the 30-min measurement time. The responsivity of pressure sensors, defined as the spectral shift of F-P fringes in response to the air pressure change, was achieved as large as 1.28 nm/mmHg at 1300-nm wavelength when using a diaphragm diameter of $20~\mu \text{m}$ . Demonstrated responsivity and compactness makes the sensor suitable for medical, environmental, and other applications. An analytical model was presented describing responsivity of an F-P pressure sensor with a thin diaphragm. It has predicted that reducing the diaphragm thickness below some critical value leads to the highest possible responsivity that no longer depends on the elastic properties or thickness of the diaphragm. This upper limit for the responsivity can be increased using the cavity shape other than a simple cylinder, while residual strength of the diaphragm results in reduced responsivity.

By employing polydimethylsiloxane (PDMS) characterized by elevated thermo-optical and elastic-optical coefficients for encapsulating an optical microfiber coupler integrated with a sagnac loop (OMCSL) structure, which exhibits large abrupt field characteristics, a fiber optic sensor capable of simultaneously measuring seawater temperature and pressure can be created. Nevertheless, the utilization of the traditional sensitivity matrix method (SMM) for demodulating the sensor led to unstable and considerably erroneous demodulation results. To enhance the accuracy of the demodulation process, this paper investigates and employs a machine learning method (MLM) for sensor demodulation. This paper centers on the investigation and application of MLM for sensor demodulation. The experimental results exhibit a significant decrease in demodulation error attained via MLM when contrasted with the traditional SMM.

Optical fibre pressure sensors have potential performance advantages over electrical sensors in measuring rapid transients such as shock waves from explosive blasts. We report the development of micromachined optical fibre Fabry–Pérot pressure sensors using a silicon dioxide or nitride diaphragm and detail the fabrication stages of the sensor body and diaphragm. The planar technology used is based on silicon deep etching and direct fusion bonding of silicon wafers. Test results for both types of diaphragm are presented. Sensors with rise times better than 3 µs, range 0.1 to 1 MPa and resolution ∼500 Pa have been demonstrated in explosives trials. Despite the difference in the sign of stress for the two diaphragm types, both demonstrated excellent high-speed response to explosively generated air shocks.

PDMS-based liquid-core optical fiber fluorescence pressure sensor

Optical fiber pressure sensors have been developed for use on a structurally-adaptive `smart wing'; further details of the design, fabrication and testing of the smart wing concept are presented in companion papers. This paper describes the design, construction, and performance of the pressure sensor and a combined optical and electronic signal processing system implemented to permit the measurement of a large number of sensors distributed over the control surfaces of a wing. Optical fiber pressure sensors were implemented due to anticipated large electromagnetic interference signals within the operational environment. The sensors utilized the principle of the extrinsic Fabry-Perot interferometer (EFPI) already developed for the measurement of strain and temperature. Here, the cavity is created inside a micromachined hollow-core tube with a silicon diaphragm at one end. The operation of the sensor is similar to that of the EFPI strain gage also discussed in several papers at this conference. The limitations placed upon the performance of the digital signal processing system were determined by the required pressure range of the sensors and the cycle time of the control system used to adaptively modify the shape of the wing. Sensor calibration and the results of testing performed are detailed.

A single-chip pressure and temperature sensor system with on chip electronics for measuring blood pressure and temperature in human arteries is presented. The pressure sensor is fabricated by surface micromachining techniques using a CMOS process. For the signal processing switched capacitor circuits are used. The sensor signals are converted to a pulse width modulated output signal.

This chapter contains sections titled: Electrically Conductive Silicone Rubber High-Voltage Insulation Silicone Rubber Composite Insulators Electromagnetic Wave Absorber Suppression of Surface Charge Heat Dissipation Devices Optical Fiber Sensor Optical Semiconductor Device Light-Emitting Devices Capacitance Sensors Dielectric Elastomer Transducers Solar Cells Portable Electronic Devices Cable Accessories Electrophotography Secondary Battery Pack Pressure and Temperature Sensor Piezoresistive Device Proton Exchange Membrane Fuel Cells Light-Emitting Diodes Recycling of Used Composite Electric Isolators Triboelectric Nanogenerator for Wearable Electronics Large Specific Surface Area Electrodes Casing