Optimal Magnetic Field Shielding Method by Metallic Sheets in Wireless Power Transfer System

Analog-to-digital converter (ADC) is becoming of utmost importance in an automotive environment. With the increased number of magnetic field sources near the ADC that can alter its behaviors significantly, we need to model how magnetic field affects the performance of the ADC. Therefore, in order to accurately evaluate the practical performance of the ADC and the considerable off-chip and on-chip effects that are highly complex, the chip-printed circuit board (PCB) comodeling, cosimulation, and coanalysis are required. In this study, a comodel of the magnetic field effects on an ADC is proposed. The proposed comodel includes three separate submodels: a model of the magnetic field coupling from the wireless power transfer (WPT) system input to the PCB integrated with ADC, a model of the noise coupling from the PCB to the ADC input, and a model of the ADC behavior from the ADC input to the ADC outputs. Considering the magnetic field coupling from the magnetic field source to the PCB, a new inductive transmission line model (I-TLM) method is developed. This method achieves fast, precise, and broadband estimation of the magnetic field effects in comparison to previous estimation methods. To validate the proposed comodel, an ADC is fabricated using a 0.13-μm complementary metal-oxide semiconductor process and is wire-bonded to the designed PCB for ADC. A PCB-level WPT system is designed and built as the magnetic field source. The performance factor of the ADC is measured by sweeping the WPT system input frequency from 100 kHz to 1 GHz to find out the critical WPT system frequency for the designed ADC with the chip-PCB hierarchical structure. The results estimated by the proposed model correlate well with the full 3-D electromagnetic field simulation and measurement. The proposed modeling procedure reduces the time and computation resource in the design of the chip, package, and PCB to achieve high-quality analog devices or mixed-mode systems, while also providing an intuitive understanding of the radiated noise effect.

The magnetic fields (MF) generated in close proximity to high power wireless power transfer (WPT) systems generally exceed exposure limits and might also violate basic restrictions (BR). However, there are as yet no available standards describing methods to measure the MF generated by WPT systems. In this study, a new method for demonstration of compliance with the BR in the close proximity to sources at frequencies from 3 kHz to 10 MHz is proposed. This approach mitigates overestimation by incident field assessment in strong field gradients close to WPT systems. The spatial peak MF amplitude and gradient generated by WPT systems are measured with a field gradient probe at the closest location to the source. The induced fields and absorbed power are then calculated on the basis of specific transformation functions for testing of compliance with the BR of all international safety guidelines.

A Wireless Power Transfer (WPT) system, known for its contactless power delivery, is extensively used for power supply in spacecraft applications. Achieving efficient and stable power transfer necessitates the integration of DC/DC converters on both the primary and secondary sides of WPT systems for power conversion and control. Traditional efficiency optimization methods primarily focus on impedance matching within the wireless power resonance network, often neglecting the overall efficiency optimization of multi-stage DC-DC and WPT systems. This oversight results in suboptimal overall system efficiency despite optimal efficiency in the wireless transmission segment. Additionally, the time-varying nature of mutual inductance and load parameters during power transmission in WPT systems presents challenges for maximum efficiency tracking and power control. This paper introduces a multi-level coordinated control efficiency optimization method for WPT systems utilizing the particle swarm optimization (PSO) algorithm. This method takes into account the transmission losses across all power conversion units within the WPT system, establishing a mathematical model for the joint optimization of overall system transmission efficiency and power. The PSO algorithm is then employed to solve this optimization model using estimated mutual inductance and load values. By adjusting the DC/DC converters on both sides, the method ensures optimal overall system efficiency and consistent power transmission. Experimental results indicate that under varying load and mutual inductance conditions, a Series–Series (SS) compensated WPT system using this method achieves a 200 W power output with maximum efficiency tracking, a power output error of 0.63%, and an average transmission efficiency of 86.2%. This demonstrates superior power transmission stability and higher efficiency compared to traditional impedance matching methods.

A wireless power transfer (WPT) system via magnetic resonance coupling method is attracting attention to high convenience. A WPT system has problems such as power transmitting loss and output voltage fluctuation due to the change in the coupling coefficient and the load state. In previous method, sliding mode control system as a tracking controller considering nonlinearity and uncertainty has been proposed, but the output of this control system had bias and chattering. This paper proposes operator-based nonlinear sliding mode control system to reduce chattering and bias simultaneously for a WPT system using buck converter. First, the model of the WPT system using rectifier and buck converter is explained and dynamics formulas are derived. Next, the proposed operator-based nonlinear sliding mode control system design for the WPT system is described and tracking performance is confirmed. Finally, the result of simulation of constant voltage control and comparison with the previous method is shown.

The wireless power transfer (WPT) system based on parity-time (PT) symmetry has the advantages of robustness, stable, and efficient power transmission. However, the region of PT symmetry is limited, which cannot satisfy some practical requirements. Multiple transmitting coils have been shown to improve the misalignment tolerance of WPT systems. Towards this end, a parity-time-symmetric-based WPT (PT-based WPT) system with double-transmitting coil is presented in this article. First, an approximate equivalent circuit model of this PT-based WPT system was developed. Second, compared with the conventional single transmitting coil PT-based WPT system, the proposed system expands the PT symmetry region and provides higher output power and transmission efficiency. Furthermore, the mutual inductance between two transmitting coils can be designed to meet the requirements of different scenarios, which improves the freedom of system design. Finally, a 30 W prototype is designed to evaluate the proposed WPT system. Experimental results show that the critical coupling coefficient is reduced by about 12.5% at <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">k</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">12</sub> = 0.51, which implies a longer transmission distance. Moreover, the maximum output voltage fluctuation in the strongly coupled region is only 3.5%, while the transfer efficiency is approximately constant, which implies stable and efficient power transfer.

Wireless power transfer (WPT) systems have attracted considerable attention in relation to providing a reliable and convenient power supply. Among the challenges in this area are maintaining the performance of the WPT system with the presence of a human body and minimizing the induced physical quantities in the human body. This study proposes a magnetic resonant coupling WPT (MRC-WPT) system that utilizes a resonator with a grounded loop to mitigate its interaction with a human body and achieve a high-efficiency power transfer at a short range. Our proposed system is based on a grounded loop to reduce the leakage of the electric field, resulting in less interaction with the human body. As a result, a transmission efficiency higher than 70% is achieved at a transmission distance of approximately 25 cm. Under the maximum-efficiency conditions of the WPT system, the use of a resonator with a grounded loop reduces the induced electric field, the peak spatial-average specific absorption rate (psSAR), and the whole-body averaged SAR by 43.6%, 69.7%, and 65.6%, respectively. The maximum permissible input power values for the proposed WPT systems are 40 and 33.5 kW, as prescribed in the International Commission of Non-Ionizing Radiation Protection (ICNIRP) guidelines to comply with the limits for local and whole-body average SAR.

In previous researches, an operator-based sliding mode control design to achieve high power transfer efficiency of a wireless power transfer (WPT) system via magnetic resonance coupling were shown. However, it is difficult to reduce the steady-state error by using SMC-based tracking controller. In this paper, an operator-based integral sliding mode control method is adopted to reduce the steady-state error in the WPT system. Moreover, high power efficiency should be achieved in the WPT system by using an impedance matching control. The effectiveness of the proposed method is verified by simulation results.

In wireless power transfer (WPT) systems, magnetically coupled wireless power transfer has become a major research focus due to its advantages such as long transmission distance, strong tolerance to misalignment, and high power transfer capability. It is also widely applied in vehicle wireless power transfer systems. From the perspective of practical engineering applications, this paper investigates the problem of system parameter variations caused by changes in inductance and load, in combination with magnetically coupled structures. During actual system operation, misalignment of the coupling mechanism leads to variations in mutual inductance, while the load resistance may also fluctuate. These parameter changes result in alterations to the overall output characteristics of the system, which are detrimental to stable system operation. Moreover, adopting a dual-side communication control strategy is susceptible to interference from the system’s power circuitry. To address these issues, this paper proposes a novel state variable modeling method and designs a state observer based on the extended Kalman filter (EKF) algorithm to estimate the secondary-side parameters, thereby enabling observation of the voltage across the load at the receiver side. The state observer is configured with two operating modes to monitor variations in mutual inductance and load resistance. The observer outputs are compared with the actual load-side voltage, and the effectiveness of the proposed state observer is verified.

In this study, an advanced wireless power transfer (WPT) system of two coils with the artificial magnetic conductors (AMC) is explored through simulations and experiments. The AMC structure is added on the transmitter coil, and the multiple resonant modes on the surface of the AMC can be energized. On the other hand, the AMC structure act as a magnetic field shield, which leads to the magnetic field above AMC structure is localized. Therefore, the localized resonant magnetic field enhance the transmission coefficient of the WPT system. The results show that the WPT transmission coefficient is increased from 16% to 35% in the experiment at 26.2 MHz resonant frequency when transmission distance is 3 cm. The experimental results agree with the simulation results. Additionally, AMC has the advantages of low-cost and can easily be installed on the WPT system.

&lt;sec&gt;Magnetic resonance wireless power transfer (WPT) has gradually become a popular research topic of near-field regulation in recent years, with wide applications in the fields of mobile phones, implantable medical devices, electric vehicles, and many other fields. However, several challenges remain to be addressed: near-field coupling, which induces multiple frequency splits and prevents the system from maintaining a fixed operating frequency; coupled arrays, which are susceptible to structural errors and parameter perturbations; current research, which primarily focuses on single-load transmission and has resulted in undeveloped multi-load transmission systems; the direction of transmission, which is difficult to control flexibly. In recent years, photonic artificial microstructures have provided a flexible platform for studying topological physics, arousing significant research interest in their fundamental topological characteristics. The most prominent features of topological structures are their nonzero topological invariant and the robust edge states determined by the bulk-edge correspondence: these features can overcome disturbances caused by defects and disorders. Moreover, by modulating the wave function distribution of topological states, energy can be precisely localized, enabling directional WPT. Therefore, implementing topological modes in WPT systems are of significant scientific importance.&lt;/sec&gt;&lt;sec&gt;This review summarizes recent researches on topological models for robust WPT, which are divided into three main parts. The first part introduces one-dimensional periodic topological structures, focusing primarily on the significant improvements in transmission efficiency and robustness achieved by utilizing topological edge states in the Su-Schrieffer-Heeger (SSH) model for WPT. Moreover, a composite chain formed by two SSH chains is constructed to realize a higher-order parity-time (PT) symmetric topological model. This approach solves the frequency splitting caused by coupled edge states and exhibits lower power losses in standby mode. The second part discusses several types of aperiodic one-dimensional topological chains. By introducing topological defect states at the interface between two different dimer chains, robust multi-load WPT is achieved. Furthermore, based on the integration of artificial intelligence algorithms, the SSH-like topological model enables more efficient and robust WPT than traditional SSH model. The asymmetric edge states in quasi-periodic Harper chain provide a solution for directional transmission in WPT applications. By introducing nonlinear circuits, this model enables active control of the transfer direction. The third part presents the application of high-order topological corner states in multi-load robust WPT, demonstrating the selective excitation of both symmetric and asymmetric corner modes.&lt;/sec&gt;&lt;sec&gt;Finally, the application prospects of topological modes in WPT systems are discussed. With the development of new physics, the integration of non-Hermitian physics and topological physics holds great promise for achieving simultaneous energy-information transfer, and is expected to achieve compatible WPT, wireless communication, and wireless sensing within a single system. Such a fusion technology will provide breakthroughs in efficiency, robustness, and multifunctionality for next-generation wireless systems.&lt;/sec&gt;

Experiment and analysis of a high-efficient stacked multi-Tx WPT system with identical Tx currents

In order to solve the problem of power transmission efficiency reduction resulting from misalignment in the Wireless Power Transfer (WPT) system for Autonomous Underwater Vehicle (AUVs), a novel coupling structure with strong tolerance to misalignment is proposed. A solenoid coil is selected as the transmitting coil, and the receiving coil is composed of dual combined planar coils. The WPT system can still maintain stable output under uncertain axial misalignments for AUVs. The magnetic field distribution of the proposed magnetic coupling structure is analyzed theoretically, and the distance between the coils in the dual combined planar receiving coil is optimized. The theoretical analysis shows that the proposed solenoid-dual combined planar coils coupling structure can effectively maintain a stable mutual inductance between the transmitting coil and receiving coil under different axial misalignments compared with solenoid-unipolar planar coil coupling structure. An S-S resonant compensated WPT experimental prototype is built to verify the output characteristics of the proposed magnetic coupling structure. Compared to the magnetic coupler with the unipolar planar coil, it is validated by experiment that the proposed magnetic coupler substantially enhances the stability of power transmission efficiency and output power when axial misalignment occurs. The power transmission efficiency decreases by 6.74% when axial misalignment increases from 0 to 40 mm in saltwater. Meanwhile, the variation of output power is less than 4.15%.

Magnetic field radiation (MFR) is a key issue that needs to be solved in the practical application of wireless power transfer (WPT) technology. Radiation analysis is very useful to improve and evaluate the electromagnetic safety and reliability for the system. Different from the existing finite element simulation and experimental detection methods, this paper establishes a unified magnetic field model suitable for regular polygon coils of WPT system based on electromagnetic field theory, which takes into account various factors such as coil structure and its parameters, misalignment conditions and external excitation, and discusses the different effects of the factors on magnetic field radiation. Both simulation and experimental results prove the validity of the magnetic field model, which provide a theoretical basis for the optimal design of electromagnetic shielding for WPT systems.

Many researches have been carried out by previous researchers to get better performance of a wireless power transfer (WPT) system. This research uses a partitioned shielding made of metallic material to protect WPT system from electromagnetic interference (EMI). Also, a shielding material is connected to ground, so that it can reduce occurrence of stray/parasitic capacitance between electrodes of electronic components. Both the electromagnetic interference and the stray/parasitic capacitance can deteriorate performance of WPT system. In this research, the WPT system works at voltage 14.7V, frequency 56,298 Hz, distance coil to coil is 0 till 5 cm. The efficiency of WPT system is achieved until 14.9 % (without shielding) and until 17.9% (with partitioned shielding).

A highly efficient wireless power transfer (WPT) system is required in many applications to replace the conventional wired system. The high temperature superconducting (HTS) wires are examined in a WPT system to increase the power-transfer efficiency (PTE) as compared with the conventional copper/Litz conductor. The HTS conductors are naturally can produce higher amount of magnetic field with high induced voltage to the receiving coil. Moreover, the WPT systems are prone to misalignment, which can cause sudden variation in the induced voltage and lead to rapid damage of the resonant capacitors connected in the circuit. Hence, the protection or elimination of resonant capacitor is required to increase the longevity of WPT system, but both the adoptions will operate the system in nonresonance mode. The absence of resonance phenomena in the WPT system will drastically reduce the PTE and correspondingly the future commercialization. This paper proposes an open bifilar spiral coils based self-resonant WPT method without using resonant capacitors at both the sides. The mathematical modeling and circuit simulation of the proposed system is performed by designing the transmitter coil using HTS wire and the receiver with copper coil. The three-dimensional modeling and finite element simulation of the proposed system is performed to analyze the current density at different coupling distances between the coil. Furthermore, the experimental results show the PTE of 49.8% under critical coupling with the resonant frequency of 25 kHz.