Optimized Integrated Surface Grating Design for Polarization-Stable VCSELs

High-frequency discrete and distinct mode-beating noise (MBN) spectra are an anomalous phenomenon observed in the related intensity noise spectrum from the vertical-cavity surface-emitting laser (VCSEL), which reveals strong correlation with fine-splitting transverse modes caused by non-circular emission aspect of the VCSEL with imperfect true-roundness. Such a phenomenon is demonstrated for the first time, which seriously degrades the transmission performance of high-speed and broad-band encoding data carried by the multi-mode (MM) VCSEL biased under a large DC bias. In this work, the 4-ary quadrature-amplitude modulation (4-QAM) orthogonal frequency-division multiplexing (OFDM) and the non-return-to-zero on–off keying (NRZ-OOK) transmissions with the direct modulation of different 850-nm MM VCSELs, as suffered from the MBN-induced notches of the signal-to-noise-ratio (SNR) spectra, are characterized under their high-level lasing conditions with multi-mode numbers. The significant SNR degradation on the receiving and decoding performances caused by the cross-correlation between MBN and data spectra is also examined by tuning the lensed fiber along the transverse (X/Y)-axis of the VCSEL (perpendicular to the surface normal) when collimating the output beam, which finds the disorderly shifted MBN spectra, as attributed to the collection of light emitted from the overlapped gain region of different transverse modes. In contrast, the MBN reveals invariant spectral features while the lensed fiber is either back-and-forth tuning along the vertical (Z)-axis (parallel with the surface normal) or tilting its angles from the surface normal under the same horizontal position and distance concerning the MM VCSEL. Such MM VCSEL exhibits several MBN spikes to decay the SNRs of NRZ-OOK and QAM OFDM data encoded around 21 and 34 GHz. For other MM VCSELs with reducing numbers of their transverse lasing modes and deforming roundness of their circular emitting aspects, the corresponding MBN spectral peaks can also be respectively observed at 14/17/24 GHz and 4.5/10.5/13 GHz to degrade the SNRs of the encoded data at such frequencies. Even though pre-emphasized encoding technology is employed, such an MBN effect is strongly correlated with the asymmetric circular aspect of the VCSEL with a degraded roundness ratio, which still affects the data modulation performance of the MM VCSEL for data center communication.

Multimode VCSEL(Vertical Cavity Surface Emitting Laser) coupling into MMF (Multimode Optical Fiber) and its influence on MMF link has been numerically studied. Considering the transverse misalignment between VCSEL and MMF, coupling efficiency between VCSEL higher-order modes and modes of MMF is calculated and the Mode Power Distribution in the MMF is obtained. Simulation of MMF link with multimode VCSEL indicates that the higher-order VCSEL modes lead to decreasing of the eye opening of received signal. The transverse misalignment of VCSEL between MMF greatly deteriorates the eye opening. With 300m OM3-MMF link , the EOP (eye-opening-penalty) is greater than 14dB when the misalignment between VCSEL and MMF is lager than 5μm.

Remarkable progress made in performance characteristics and reliability of high-speed (> 10 GHz) 850-nm multi-mode (MM) oxide-confined vertical cavity surface emitting lasers (VCSELs) during the last decade has led them to find applications in space satellite systems. The main advantage of deploying high-speed VCSELs in space satellites over directly modulated 850-nm edge emitting lasers is the absence of COMD (catastrophic optical mirror damage). In recent years, leading VCSEL manufacturers introduced higher speed (~ 20 GHz or 25 Gbps) VCSELs with encouraging characteristics. However, little has been reported on reliability and failure modes of these state-of-the-art VCSELs although it is crucial to understand failure modes and degradation mechanisms in these VCSELs through physics of failure investigation and subsequently develop VCSELs that exceed lifetime requirements for space satellite systems. For the present study, we performed short-term and long-term accelerated life-tests on 25 Gbps oxide-confined MM VCSELs to study reliability of these devices. Our goal is to extract credible reliability model parameters (thermal activation energy and current exponent factor) from these life-tests to determine suitability of these lasers for future space satellite systems. We also performed failure mode analysis on VCSELs at different stages of degradation using various techniques. We employed nondestructive techniques including optical beam induced current (OBIC) and electron beam induced current (EBIC) techniques as well as destructive techniques including focused ion beam (FIB) and high-resolution TEM techniques. Our detailed reliability and failure mode analysis results are reported along with our understanding on the physical origin of degradation in high-speed VCSELs with strained InGaAs quantum wells.

Persistent efforts on developing advanced and complex data algorithms to enable the vertical-cavity surface-emitting lasers (VCSELs) for data beyond 100-Gbit/s has been reviewed in this paper. This endeavor not only elevates the bit rate of the IEEE802.3 standards for data center applications but also to initiate the unification of data format for wired and wireless network coverage. To date, the highest allowable data rates of the single-VCSEL-based optical link are 80 Gbit/s for the NRZ-OOK format under back-to-back (BtB) transmission 168 Gbit/s for the PAM-4 format over 150-m OM5 MMF, and the 224 Gbit/s for the QAM-OFDM format at BtB case. For the high-level complex data-format transmission with rigorous demand on the signal-to-noise ratio (SNR), this work demonstrates the most up-to-date 32-ray quadrature amplitude modulation generalized frequency division multiplexing (32-QAM GFDM) data algorithm with optimized amplitude and K value for encoding the multimode (MM) VCSEL. To achieve the higher spectral-usage efficiency based on the SNR spectrum for maximal transmission data rate, the bit-loading discrete multi-tone (DMT) technique is implemented by rearranging each subcarrier to the appropriate QAM levels. By utilizing 32-QAM GFDM and bit-loading DMT, the maximal data rate in the BtB case could respectively achieve 119.5 Gbit/s and 130 Gbit/s when operating the MM VCSEL at 55 °C. The transmission capacity of the VCSEL operated at 55 °C would decrease to 93.8 Gbit/s for 32-QAM GFDM and 83 Gbit/s for bit-loading DMT after propagating through OM5 MMF with modal dispersion.

Short-reach optical interconnects among massive serves in data centers have attracted extensive research recently. Increasing capacity, cost and power efficiency as well as wavelength switching between data center network nodes are still key challenges for current optical interconnects. In this work, we experimentally demonstrate the real-time inter-mode optical wavelength switching technique, for high-speed wavelength flexible data center interconnects. A 10 Gbit/s 1 550 nm single mode vertical cavity surface emitting laser (VCSEL) is optically injected and used to control a 10 Gbit/s multimode VCSEL carrier at 850 nm. Results show that a clearly open eye diagram is achieved at back-to-back analysis, implying a successful wavelength switch and error-free operation at 10 Gbit/s. A fully optical wavelength conversion of a multimode VCSEL operation at 850 nm using a single mode VCSEL subject to external optical injection at 1 550 nm is reported. This work opens new perspectives towards the development of a cost effective high-speed real-time inter-band wavelength switching technique between servers and network devices operating at different transmission windows at network nodes, for current and future optical interconnects.

The dependence of the mode partition noise (MPN) and the power penalty associated with it can be measured from the source spectral width. Our findings show that there is strong dependence of the carrier lifetime on the bit error rate degradation caused by MPN on the spectral width of the vertical cavity surface emitting laser (VCSEL). VCSELs with smaller spectral width (shorter carrier lifetime) exhibited smaller MPN induced power penalty. We found that the theoretical calculation of the power penalties caused by MPN from the carrier lifetime and the spectral width is in good agreement with the measured system penalties.

A theoretical study of single and multimode vertical-cavity surface-emitting lasers (VCSELs) subject to pseudorandom modulation of the current at a rate of 10 Gb/s is performed. Eye diagrams, probability density functions of the power at the decision time, averaged turn-on delay, and timing jitter are analyzed for different values of the on- and off-state currents. Bit sequences where errors occur are identified. Extensive simulations have been performed to obtain the bit-error rate (BER) for the back-to-back configuration. We find that the BER performance of single-mode VCSELs is better than the one obtained with multimode VCSELs when the off-state current is smaller than the threshold current. The same result is obtained when the off-state current is larger than the threshold value, providing that the on-state current is large enough. However, BER in single-mode VCSELs is greater than in multimode VCSELs when the off-state current is equal to the threshold current. BER performance is also better for multimode VCSELs when the off-state current is larger than the threshold value, if the on-state current is small enough.

A comprehensive numerical model has been applied to simulate single and multimode vertical-cavity surface-emitting lasers (VCSELs) with pseudorandom modulation of the current at a rate of 10 Gb/s. Eye diagrams, probability density functions of the power at the decision time, averaged turn-on delay and timing jitter are analysed for different values of the on and off-state currents. Extensive simulations have been performed to obtain the Bit Error Rate (BER). We find that the BER performance of single-mode VCSELs is better than the one obtained with multimode VCSELs when the off-state current is smaller than the threshold current and when the off-state current is larger than the threshold value, providing that the on-state current is large enough. However BER in single-mode VCSELs is greater than in multimode VCSELs when the off-state current is equal to the threshold current and when the off-state current is larger than the threshold value, if the on-state current is small enough

Real-time wavelength switching and routing at key access network nodes is an emerging fundamental functionality requirement for transparent content resolution and wavelength assignment towards better utilization of network resources under dynamic traffic patterns. In this paper, we experimentally demonstrate the first vertical cavity surface emitting laser (VCSEL)-based broadband switch for ultra-wide wavelength data traffic routing in Datacom. An 850 nm multimode VCSEL is directly modulated with 8.5 Gbps data and successfully transmitted error free over 100.3 m of OM3 multimode fibre link. At the integration node, the received data signal is used to drive a second VCSEL at 1550 nm, and forwarded over a second network link over 24.7 km of single mode fibre. We therefore achieve the first reported all-optical, real-time, inter-band wavelength switch to C-band. By exploiting wavelength tuneability, the 1550 nm VCSEL-based forwarding node is tuned to over 3.2 nm spectral range, for ultra-wide data routing over the second network link. A receiver sensitivity of -14.28 dBm of the converted signal is achieved at back-to-back analysis at the integration node. An additional penalty of 2.72 dB is introduced over the 24.7 km of single mode fibre transmission link. This work offers a viable enabling development technology for broadband wavelength converters for application real-time wavelength routing in the access network, to address content resolution and wavelength assignment problem for current and future Datacom.

Vertical-cavity surface-emitting lasers (VCSELs) are widely used in optical data communication mainly in data centers for short-haul transmissions. However, their intensity modulation resonance frequency does not exceed 40 GHz which also limits the achievable modulation bandwidth and data rate. In contrast, spin-VCSELs can overcome these bandwidth limitations by modulating spin and polarization instead of current and intensity. In spin-VCSELs, the birefringence determines the resonance frequency of the polarization dynamics as well as the modulation bandwidth. We control the birefringence and thus the polarization dynamics via the elasto-optic effect by mechanically or thermally induced strain providing polarization oscillation frequencies up to more than 200 GHz. Detailed analysis shows that spin-VCSELs offer polarization dynamics with good signal strength even when operating close to threshold and at high temperatures. Here, we analyze devices with integrated surface gratings. VCSELs with different grating periods as well as mesa diameters and resulting different oxide apertures were investigated.

A 780 nm-range 40 channels vertical-cavity surface-emitting laser (VCSEL) array was developed as a writing light source for printers. A 15° off missoriented GaAs substrate, an aluminum-free GaInAsP/GaInP compressively-strained multiple quantum well and an anisotropic-shape transverse-mode filter were employed to control polarization characteristics. The anisotropic-shape transverse-mode filter also suppressed higher transverse-mode and enabled high-power single-mode operation. Thus, orthogonal-polarization suppression-ratio (OPSR) of over 22 dB and side-mode suppression-ratio (SMSR) of 30 dB were obtained at operation power of 3mW at same time for wide oxide-aperture range below 50 μm2. Moreover, a thermal resistance was reduced for 38% by increasing a thickness of high thermal conductivity layer (3λ/4-AlAs layer) near a cavity. By this structure, a peak-power increased to 1.3 times. Moreover, a power-fall caused by self-heating at pulse-rise was decreased to 10% and the one caused by a thermal-crosstalk between channels was decreased to 46%. The VCSEL array was mounted in a ceramic package with a tilted seal glass to prevent optical-crosstalk caused by other channels. Thus, we achieved stable-output and high-quality beam characteristics for long-duration pulse drive.

An extensive theoretical study was performed on the dynamic behavior of 850-nm-wavelength oxide-confined fundamental-mode stabilized vertical-cavity surface-emitting lasers (VCSELs), using a shallow surface relief. The surface relief is used to provide lower mirror loss for the fundamental mode, thus acting as a mode discriminator. In this way, single-mode operation at high power levels can be obtained. We utilized a comprehensive model that includes the detailed epitaxial layer structure and device geometry when calculating the optical fields and that accurately accounts for the dynamic effects of carrier density and temperature on the modal distributions. Modulation response, eye diagrams, bit error rate (BER), and relative intensity noise (RIN) were simulated and compared to the performance of VCSELs without a mode discriminator, i.e., conventional multimode VCSELs. The fundamental-mode stabilized VCSELs are associated with a higher out-coupling, which lowers the relaxation oscillation frequency and damping, and strong spatial hole burning, which induces a low-frequency roll-off in the modulation response and contributes to the damping of the relaxation oscillation at low bias. However, their dynamics is fully competitive with conventional multimode VCSELs at both 2.5 and 10 Gb/s although they exhibit a slightly higher eye closure. We only found a 0.5-dB power penalty in the BER. The RIN is enhanced, with a peak that is about 10-15 dB higher, caused by the lower damping of the relaxation oscillation. It should be noted that in the comparison we assume that all modes are equally captured from the multimode VCSEL. A mode-selective loss can severely degrade its performance.

Free-space optical interconnects (FSOIs) utilize arrays of vertical-cavity surface emitting lasers (VCSELs), microlenses, and photodetectors to effectively overcome the communication bottleneck caused by the poor performance of electrical interconnects. We derived a comprehensive FSOI link equation which can be used to determine the interconnect performance parameters, such as the receiver carrier-to-noise ratio. The link equation includes both optical and electrical noise components. The optical noise component is caused mainly by laser beam diffraction. We have simplified the modeling of optical noise by using the recently introduced Mode Expansion Method. The optical noise component strongly depends on the modal content of the incident VCSEL beam. The models used in the literature assume that the cross-sectional profile of the emitted laser beam resembles the fundamental Gaussian mode. Our link equation takes into account the modal structure of a multimode VCSEL beam. We have investigated the FSOI performance and we found that for each merit function there exists a single set of design parameters yielding the optimal performance. We have also found that the presence of higher-order modes negatively affects the performance. Our results show that FSOIs based on multimode VCSELs can be utilized in chip-level interconnects despite increased beam diffraction.

This paper introduces a novel approach for transmitting UWB signals over optical fibre with cost effective Vertical-cavity surface-emitting laser (VCSEL). The transmitted impulse compile with the strict European frequency plan (ECC). A prototype filter is presented with lumped elements which has a −40 dB/500 MHz cut off at the critical 3.1 GHz band. Also a novel impedance matching method is presented for matching low cost 850 nm multi-mode VCSEL in the lower UWB band. Time-domain transmission measurements are presented with the fabricated devices that show this approach is acceptable for low cost remote antenna connection for UWB applications.

Using transfer matrix method and TFcalc thin film design software,the reflectance spectrum of distributed Bragg reflector (DBR) and vertical cavity surface emitting laser (VCSEL) are simulated.The reflectance spectra from the cavity and surface are compared with each other,thus providing the basis for white light source (WLS) optical reflectance spectrum of the VCSEL epitaxial wafer.When using WLS to characterize VCSEL wafer,it is necessary to combine the simulation results and the shape of optical reflectance spectrum to speculate the reflectance seen from the cavity.The influences of different cap layers on the reflectance of DBRs are discussed theoretically and experimentally.With a 1/4 GaAs cap layer,the reflectance reaches up to 97.8% seen from the cavity.This design can make the wavelength of the VCSEL etalon picked easily because of avoiding the influence of test noise. The active region has higher heat accumulation due to the small area and poor thermal conductivity.The characteristics of the gain spectrum of InGaAs/AlGaAs strained quantum well (QW) under different temperatures and the temperature distribution in VCSEL are simulated by Crosslight software.The gain-to-cavity wavelength detuning is used to improve the slope efficiency and the temperature stability.The temperature in active region ranges from 360 K to 370 K.The gain peak wavelength and the Fabry-Perot cavity wavelength are designed in the ranges of 829-832 nm and 845-847 nm,respectively.Epitaxial wafer with top-emitting VCSEL structure grown by metal-organic chemical vapor deposition is characterized.The room temperature photoluminescence peak is at 827.5 nm and the etalon cavity wavelength measured by optical reflectance is 847.7 nm,which are consistent with designed values. The oxide restricted VCSELs with 7.5 m oxide aperture are fabricated.The image of the infrared light source CCD shows that the oxide aperture is circular.A passivation layer of 120 nm SiO2 is finally deposited to insulate water vapor.The threshold current is 0.8 mA,and the maximum output power reaches up to 9 mW at 13.5 mA.The optical spectrum at 6.0 mA reveals multiple transverse modes.The center wavelength is 852.3 nm and the root mean square (RMS) spectrum width is 0.6 nm,meeting the high-speed Datacom standards.Shannon theory indicates that the maximum data rate is not only proportional to bandwidth but also related to signal-to-noise ratio (SNR).It is effective to reduce relative intensity noise and enhance the SNR by increasing output power.From the eye diagram of 25 Gbit/s on-off key VCSEL,it is demonstrated that fall time is 38.66 ps,rise time is 41.54 ps,SNR is 5.6,and jitter RMS is 1.57 ps.Clear eye opening is observed from eye diagram of 25 GBaud/s PAM-4 VCSEL,which indicates the qualified 50 Gbit/s high speed performance.