Optimizing Products and Production Using Additive Manufacturing by Introducing Bionics Into the Engineering Design Process

Research in additive manufacturing (AM) has increased the use of AM in many industries, resulting in a commensurate need for a workforce skilled in AM. In order to meet this need, educational institutions have undertaken different initiatives to integrate design for additive manufacturing (DfAM) into the engineering curriculum. However, limited research has explored the impact of these educational interventions in bringing about changes in the technical goodness of students' design outcomes, particularly through the integration of DfAM concepts in an engineering classroom environment. This study explores this gap using an experimental study with 193 participants recruited from a junior-level course on mechanical engineering design. The participants were split into three educational intervention groups: (1) no DfAM, (2) restrictive DfAM, and (3) restrictive and opportunistic (dual) DfAM. The effects of the educational intervention on the participants' use of DfAM were measured through changes in (1) participants' DfAM self-efficacy, (2) technical goodness of their AM design outcomes, and (3) participants' use of DfAM-related concepts when describing and evaluating their AM designs. The results showed that while all three educational interventions result in similar changes in the participants' opportunistic DfAM self-efficacy, participants who receive only restrictive DfAM inputs show the greatest increase in their restrictive DfAM self-efficacy. Further, we see that despite these differences, all three groups show a similar decrease in the technical goodness of their AM designs, after attending the lectures. A content analysis of the participants' design descriptions and evaluations revealed a simplification of their design geometries, which provides a possible explanation for the decrease in their technical goodness, despite the encouragement to utilize the design freedom of AM to improve functionality or optimize the weight of the structure. These results emphasize the need for more in-depth DfAM education to encourage the use of both opportunistic and restrictive DfAM during student design challenges. The results also highlight the possible influence of how the design problem is stated on the use of DfAM in solving it.

Additive manufacturing (AM) has recently been accorded considerable interest by manufacturers. Many manufacturing industries, amongst others in the aerospace sector, are already using AM parts or are investing in such manufacturing methods. Important material properties, such as microstructures, residual stress, and surface topography, can be affected by AM processes. In addition, a subtractive manufacturing (SM) process, such as machining, is required for finishing certain parts when accurate tolerances are required. This finish machining will subsequently affect the surface integrity and topography of the material. In this research work, we focused on the surface integrity of Ti-6Al-4V parts manufactured using three different types of AM and finished using an SM step. The aim of this study was to gain an understanding on how each process affects the resulting surface integrity of the material. It was found that each AM process affects the materials’ properties differently and that clear differences exist compared to a reference material manufactured using conventional methods. The newly generated surface was investigated after the SM step and each combination of AM/SM resulted in differences in surface integrity. It was found that different AM processes result in different microstructures which in turn affect surface integrity after the SM process.

Additive manufacturing (AM) has gained notoriety for offering advantages over traditional manufacturing methods, such as increased design complexity and flexibility. However, it has not found widespread use beyond rapid prototyping. One hindrance to the acceptance of AM processes in industry is the time and cost of fabrication per component. While metal AM by itself can be inexpensive, extra manufacturing steps in the form of subtractive manufacturing (SM) may need to be performed to reach final part tolerances, leading to hybrid additive-subtractive manufacturing (HASM) of a part, which increases time and cost. A potential area to reduce cost is through increasing the efficiency of the HASM process by conducting additive and subtractive manufacturing simultaneously. Usually, HASM is performed in a process where AM is completed in one machine or cell and transferred to another machine or cell for SM in a sequential assembly line process. This efficiency decreases part cost, but high aspect ratio parts or parts with internal geometry that require interleaved additive deposition and machining cannot be produced. One unexplored solution to simultaneous HASM that allows for interleaved operations is to operate the deposition head and machining spindle concurrently within the same machine envelope, known as concurrent HASM (CHASM). In this type of process, both AM and SM occur simultaneously on a batch of small parts or a single large part, maintaining a high efficiency without sacrificing the full range of complex geometries that AM allows for. A potential approach to the single-machine method could be to combine a robot and mill within the same envelope. A challenge to this approach, however, is control of both systems. Most machine controllers have limited external communication or, if a robot has been integrated, only offer movement of either the robot or mill at any given time. As a result, systems must pause either the AM or SM process to switch between them rather than working simultaneously. The present work investigates the positional accuracy of such a CHASM system comprised of a robotic arm and a 3-axis mill. Open-loop tests with limited communication between machines are performed on the system to verify positional error during concurrent robot-mill movements. Under certain conditions, it is demonstrated that position error can stay within 2 mm for the duration of a single layer; however, these tests show that, generally, the open-loop positioning performance of the system is inadequate for CHASM without part-specific hand-tuning of parameters. Based on these results, a set of requirements for successful robot-CNC CHASM is proposed for future integrations.

PurposeThis paper aims to present a systematic approach in the literature survey related to metal additive manufacturing (AM) processes and its multi-physics continuum modelling approach for its better understanding.Design/methodology/approachA systematic review of the literature available in the area of continuum modelling practices adopted for the powder bed fusion (PBF) AM processes for the deposition of powder layer over the substrate along with quantification of residual stress and distortion. Discrete element method (DEM) and finite element method (FEM) approaches have been reviewed for the deposition of powder layer and thermo-mechanical modelling, respectively. Further, thermo-mechanical modelling adopted for the PBF AM process have been discussed in detail with its constituents. Finally, on the basis of prediction through thermo-mechanical models and experimental validation, distortion mitigation/minimisation techniques applied in PBF AM processes have been reviewed to provide a future direction in the field.FindingsThe findings of this paper are the future directions for the implementation and modification of the continuum modelling approaches applied to PBF AM processes. On the basis of the extensive review in the domain, gaps are recommended for future work for the betterment of modelling approach.Research limitations/implicationsThis paper is limited to review only the modelling approach adopted by the PBF AM processes, i.e. modelling techniques (DEM approach) used for the deposition of powder layer and macro-models at process scale for the prediction of residual stress and distortion in the component. Modelling of microstructure and grain growth has not been included in this paper.Originality/valueThis paper presents an extensive review of the FEM approach adopted for the prediction of residual stress and distortion in the PBF AM processes which sets the platform for the development of distortion mitigation techniques. An extensive review of distortion mitigation techniques has been presented in the last section of the paper, which has not been reviewed yet.

3D printing is finding more and more applications in the industrial field and represents a modern additive manufacturing process based on a digital model. There are a number of advantages of additive manufacturing through 3D printing compared to classic manufacturing processes. Additive manufacturing through 3D printing allows material savings compared to classic manufacturing processes. Material consumption is punctual according to the project, without unnecessary losses and excess material. Through additive manufacturing, the design can be optimized in the sense that rapid changes can be made to the prototype in the CAD file. Also, through additive manufacturing through 3D printing, the principle of sustainability is promoted. We can say that additive manufacturing through 3D printing ensures rapid prototyping, which leads to the development of new products, shortens the design and manufacturing cycle, improves the quality and precision of models, eliminates costly mistakes, and optimizes the way of collaboration between engineers, marketing departments and sales and management team. In addition to these advantages, it must be seen if the 3D printed elements can replace the elements manufactured by classical methods in terms of mechanical resistance. In this sense, an investigation of some mechanical properties of some samples manufactured by 3D printing from various types of materials is required. The samples will be subjected to tension and bending. In this paper, only the tensile tests of some specimens, obtained by 3D printing in three positions: horizontal, vertical and in height, using three categories of printing filaments of the type: ABS+, PETG, PLA+, are presented. They have been made 5 samples for each material and printing direction, resulting in a total of 45 samples. The samples made from the three categories of material and in the three printing positions were subjected to tension until breaking. The formulas that were the basis of the tests are presented and graphs are drawn that represent the average characteristic curves of the samples for each category of material and printing guidelines.

Comparative study on life cycle assessment of components produced by additive and conventional manufacturing process

PurposeMaterial extrusion (MEX) is a class of additive manufacturing (AM) process based on MEX principle. In the viewpoint of Industry 4.0 and sustainable manufacturing, AM technologies are gaining importance than conventional manufacturing route (subtractive manufacturing). Because of the ease of use and lesser operation skills, MEX had wide popularity in industry for product and prototype development. This study aims to analyze energy consumption of MEX-based AM process and its influencing factors.Design/methodology/approachA group of factors were identified pertaining to MEX-based AM process. In this viewpoint, this study presents the configuration of a structural model using interpretive structural modeling (ISM) to depict dominant factors in MEX-based AM process. A total of 18 influencing factors are identified and ranked using ISM methodology for MEX process. The Impact Matrix Cross-reference Multiplication Applied to a Classification analysis was done to categorize influencing factors into four groups for MEX-based AM process.FindingsThe derivation of structural model would enable AM practitioners to systematically analyze the factors and to derive key factors which enable comprehensive energy modeling and energy assessment studies. Also, it facilitates the development of energy efficient AM system.Originality/valueThe development of structural model for analysis of factors influencing energy consumption of MEX-based AM is the original contribution of the authors.

PurposeDue to the complexity of and variations in additive manufacturing (AM) processes, there is a level of uncertainty that creates critical issues in quality assurance (QA), which must be addressed by time-consuming and cost-intensive tasks. This deteriorates the process repeatability, reliability and part reproducibility. So far, many AM efforts have been performed in an isolated and scattered way over several decades. In this paper, a systematically integrated holistic view is proposed to achieve QA for AM.Design/methodology/approachA systematically integrated view is presented to ensure the predefined part properties before/during/after the AM process. It consists of four stages, namely, QA plan, prospective validation, concurrent validation and retrospective validation. As a foundation for QA planning, a functional workflow and the required information flows are proposed by using functional design models: Icam DEFinition for Function Modeling.FindingsThe functional design model of the QA plan provides the systematically integrated view that can be the basis for inspection of AM processes for the repeatability and qualification of AM parts for reproducibility.Research limitations/implicationsA powder bed fusion process was used to validate the feasibility of this QA plan. Feasibility was demonstrated under many assumptions; real validation is not included in this study.Social implicationsThis study provides an innovative and transformative methodology that can lead to greater productivity and improved quality of AM parts across industries. Furthermore, the QA guidelines and functional design models provide the foundation for the development of a QA architecture and management system.Originality/valueThis systematically integrated view and the corresponding QA plan can pose fundamental questions to the AM community and initiate new research efforts in the in-situ digital inspection of AM processes and parts.

On the environmental impacts of 3D printing technology

Recently, Additive Manufacturing (AM) has been widely used in many applications. For a particular AM component, the choice of available AM processes is critical to the component’s quality, mechanical properties, and other important factors. In that context, this article presents an efficient decision support system for the selection of an appropriate AM process. A novel hybrid Multi-Criteria Decision Making (MCDM) technique has been proposed to select an appropriate AM process from available AM processes. The Best Worst Method (BWM) is used to determine optimal weights of criteria and the Proximity Indexed Value (PIV) method is employed to rank the available AM processes. For benchmarking the abilities of an AM process, a conceptual model of spur gear was fabricated by four available AM processes viz., Vat Photopolymerization (VatPP), Material Extrusion (ME), Powder Bed Fusion (PBF), and Material Jetting (MJ). Additionally, Dimensional accuracy (A), surface roughness (R), tensile strength (S), percentage elongation (%E), heat deflection temperature (HDT), process cost (PC) and build time (BT) has been considered as most significant criteria. Further, sensitivity analysis has been performed to validate the reliability of the results. The results suggested that the Material Jetting (MJ) process produces dimensionally accurate and quality parts among available alternatives AM processes. The ranking obtained using the PIV method is consistent and reliable.

The goal of this work is to predict the effect of part geometry and process parameters on the instantaneous spatiotemporal distribution of temperature, also called the thermal field or temperature history, in metal parts as they are being built layer-by-layer using additive manufacturing (AM) processes. In pursuit of this goal, the objective of this work is to develop and verify a graph theory-based approach for predicting the temperature distribution in metal AM parts. This objective is consequential to overcome the current poor process consistency and part quality in AM. One of the main reasons for poor part quality in metal AM processes is ascribed to the nature of temperature distribution in the part. For instance, steep thermal gradients created in the part during printing leads to defects, such as warping and thermal stress-induced cracking. Existing nonproprietary approaches to predict the temperature distribution in AM parts predominantly use mesh-based finite element analyses that are computationally tortuous—the simulation of a few layers typically requires several hours, if not days. Hence, to alleviate these challenges in metal AM processes, there is a need for efficient computational models to predict the temperature distribution, and thereby guide part design and selection of process parameters instead of expensive empirical testing. Compared with finite element analyses techniques, the proposed mesh-free graph theory-based approach facilitates prediction of the temperature distribution within a few minutes on a desktop computer. To explore these assertions, we conducted the following two studies: (1) comparing the heat diffusion trends predicted using the graph theory approach with finite element analysis, and analytical heat transfer calculations based on Green’s functions for an elementary cuboid geometry which is subjected to an impulse heat input in a certain part of its volume and (2) simulating the laser powder bed fusion metal AM of three-part geometries with (a) Goldak’s moving heat source finite element method, (b) the proposed graph theory approach, and (c) further comparing the thermal trends predicted from the last two approaches with a commercial solution. From the first study, we report that the thermal trends approximated by the graph theory approach are found to be accurate within 5% of the Green’s functions-based analytical solution (in terms of the symmetric mean absolute percentage error). Results from the second study show that the thermal trends predicted for the AM parts using graph theory approach agree with finite element analyses, and the computational time for predicting the temperature distribution was significantly reduced with graph theory. For instance, for one of the AM part geometries studied, the temperature trends were predicted in less than 18 min within 10% error using the graph theory approach compared with over 180 min with finite element analyses. Although this paper is restricted to theoretical development and verification of the graph theory approach, our forthcoming research will focus on experimental validation through in-process thermal measurements.

Among all the additive manufacturing (AM) technologies, the material extrusion-based AM is the most popular, and widely used for prototyping, rapid tooling, and direct part production in the current scenario. In material extrusion AM (MEAM), a solid form of material is converted to a semi-molten form and extruded out of a nozzle to deposit in a layer-by-layer manner. Nowadays MEAM three-dimensional (3D) printers are very popular among different application sectors. This motivates us to develop various commercial as well as open-source entry-level 3D printers such as the development of filament extruder 3D printers, pellet extruder 3D printer, or a combination of both. However, to develop or operate these printers, preliminary knowledge of various extrusion parameters is required to obtain the desired quality in the fabricated parts. Therefore, an initial attempt has been made to provide information related to various extrusion parameters such as definition, working range, and the effect of these parameters on performance measured. The impact of process parameters on the performance of either filament extrusion AM or pellet/granules extrusion AM has only been investigated in the studies available in the literature. However, this study provides a comprehensive review of the effects of process parameters on performance measurements for both types of extrusion-based AM processes. In this research work, along with a detailed review of previous works, a study of various process parameters, modeling, and methodology has been provided. The statistical modeling approach, histogram normal plots have been provided along with mean, standard deviation, and percentage to decide the optimum process parameters based on data available in the existing literature.

Hybrid Additive Manufacturing Technologies – An Analysis Regarding Potentials and Applications

Although the additive manufacturing (AM) market continues to grow, industries face barriers to AM adoption due to a shortage of skilled designers in the workforce that can apply AM effectively to meet this demand. This shortage is attributed to the high cost and infrastructural requirements of introducing high- barrier-to-entry AM processes such as powder bed fusion (PBF) into in-person learning environments. To meet the demands for a skilled AM workforce, it is important to explore other mediums of AM education, such as computer-aided instruction (CAI) and virtual reality (VR), which can increase access to hands-on learning experiences for inaccessible AM processes. However, limited work compares virtual and physical AM instruction or explores how the differences in immersion and presence between mediums can affect the knowledge gained and the mental effort exerted when learning about different AM processes. To address this gap in the literature, this research evaluates the use of CAI, VR, and in-person instruction in AM process education when learning about material extrusion (ME) and PBF. Our findings show that the differences in immersion and presence between CAI, VR, and in-person instruction do not have a statistically significant effect when learning about ME, but do have a significant effect when learning about PBF. Specifically, we found that VR generally yields equivalent effects in knowledge gain and cognitive load to in-person PBF education while offering advantages in both metrics over CAI learning. The findings from this work thus have significant implications for using VR as an alternative to in-person training to improve designer development in process-centric AM education of typically high-barrier-to-entry AM processes.

Purpose This paper studies the feasibility of additive manufacturing (AM) processes and their potential materials to produce mold inserts for injection molding (IM) of plastic parts. This study aims to describe the technological advancements and practical implications of integrating AM with IM to produce plastic parts, reducing the gap and determining the feasibility of AM for insert production. Design/methodology/approach A literature search of different databases was done. Applying the PRISMA methodology, the 67 most relevant articles between 2013 and 2024 were selected. From these, a bibliometric analysis was performed, and the main results regarding the mechanical properties and the number of injection cycles achieved by inserts were extracted. Findings Material jetting (MJT), vat photopolymerization via ultraviolet light laser (VPP-UVL) and laser powder bed fusion using metal powders (PBF-LB/M) are the most useful AM processes reported in the literature to produce inserts for IM. Studies show that the maximum number of successful injection cycles achieved with these AM inserts has been 116, 85 and more than 500 cycles, respectively. The molded geometry, the injected material and the IM parameters influence the number of injection cycles, being the injection pressure, the mold temperature and the injection temperature the most critical parameters to consider in extending the life of the inserts. Originality/value To the best of the authors’ knowledge, this study provides the first systematic review with a comprehensive overview of this innovative approach to evaluate the emerging directions, current barriers and future potential of using AM with IM to manufacture plastic parts. As such, this study highlights the primary findings in the literature concerning AM processes and the materials commonly used to manufacture inserts for IM.