Optimum WEDM Process Parameters of Incoloy®Alloy800 Using Taguchi Method

Engineering industry has made tremendous growth in its manufacturing fields in the last decade but still the modern machines are not utilized up to the desired level. Wire electrical discharge machining (WEDM) is one such sophisticated machining process used in industry, which is a high-speed cutting and high-precision machining to realize productivity and improved accuracy for all manufacturing parts. Optimisation of the operating parameters of WEDM will result in efficiency with regard to higher surface finish and maximum material removal rate. The present investigation of the cutting performance on die steel with different parameters such as pulse on time, pulse off time, servo voltage, wire feed, current and cutting speed were involved to determine by which using wire electric discharge machining(WEDM) process. The shape of the wire and base material dimensions of brass wire 0.25mm diameter and AISI D2 steel with 100× 100 × 10 mm were carried out. The cutting performance outputs considered in this study are material removal rate (MRR), Kerf width and surface roughness (Ra). Experiments were carried out under Taguchi's L16 orthogonal array under different conditions of parameters. An optimal combination of WEDM parameters for proper machining of AISI D2 steel to achieve better surface roughness and Materials Removal Rate (MRR) is achieved in this investigation.

PurposeAn experimental study has been conducted to model and optimize wire electric discharge machining (WEDM) process parameters such as pulse-on time, pulse-off time, servo voltage and peak current for response characteristics during machining of Nimonic 75 alloy.Design/methodology/approachThe response surface methodology (RSM)-based Box–Behnken's design has been employed for experimental investigation. RSM is used for developing quadratic regression models for selected response variables i.e. material removal efficiency and kerf width. To validate the model, confirmation experiments have been performed. The multi-response optimization has been done using desirability function approach.FindingsThrough analysis of variation, the percent contribution of process parameters on the response characteristics has been found. Pulse-off time is the most significant parameter affecting the kerf width and material removal efficiency followed by pulse-on time. The quadratic regression models have been developed for prediction of selected response variables. An attempt has been made to optimize the WEDM parameters for material removal efficiency and kerf width. The recommended process parameter setting for maximum material removal efficiency and minimum kerf width have been found to be pulse-on time = 0.6 µs, pulse-off time = 14 µs, servo voltage = 25 V and peak current = 200 A.Originality/valueThe “kerf width” is an important response variable for maintaining dimensional accuracy of the machined component, but has not been given due attention by the researchers. In the present work, the developed regression model for “kerf width” can be used in estimating wire offset setting and thereby getting a dimensionally accurate product. The optimum process parameters obtained in WEDM of Nimonic 75 alloy will contribute in database of machining. The outcome of this study would be added to scare database of the machining of Nimonic 75 alloy and also would be extremely useful for making the technology charts for WEDM.

The effect of heterogeneous second phase on the machinability evaluation of spheroidal graphite cast irons in the WEDM process

Wire EDM process parameter optimization for D2 steel

The selection of optimum machining conditions, during wire electric discharge machining process, is of great concern in manufacturing industries these days. The increasing quality demands, at higher productivity levels, require the wire electric discharge machining process to be executed more efficiently. Specifically, the material removal rate needs to be maximized while controlling the surface quality. Despite extensive research on wire electric discharge machining process, determining the desirable operating conditions in industrial setting still relies on the skill of the operators and trial-and-error methods. In the present work, an attempt has been made to optimize the machining conditions for maximum material removal rate and maximum surface finish based on multi-objective genetic algorithm. Experiments, based on Taguchi’s parameter design, were carried out to study the effect of various parameters, viz. pulse peak current, pulse-on time, pulse-off time, wire feed, wire tension and flushing pressure, on the material removal rate and surface finish. It has been observed that a combination of factors for optimization of each performance measure is different. So, mathematical models were developed between machining parameters and responses like metal removal rate and surface finish by using nonlinear regression analysis. These mathematical models were then optimized by using multi-objective optimisation technique based on Non-dominated Sorting Genetic Algorithm-II to obtain a Pareto-optimal solution set.

Wire Electrical Discharge Machining (WEDM) is a versatile process to generate intricate and complex shapes on conductive work material with high dimensional accuracy and surface finish. Since the process is stochastic, its input parameters play critical role for achieving desired accuracy and precision of the component. Inconel 718, High-Strength-Temperature-Resistant (HSTR) material, has wide applications in the field of aerospace, automobile, mould making and medical industries. Hence, machining of Inconel 718 using WEDM is a challenging task. Also experimentation on Inconel 718 with WEDM is costly as well as time consuming process. Therefore to study the behavior of WEDM process with different process parameters for effective and efficient operation, process modeling and simulation using appropriate software is highly essential. In the present investigation, a 3-D single spark finite element thermal model for WEDM process has been developed using ANSYS software. This model has some more realistic assumptions like heat flux following Gaussian distribution and spark radius as a function of time and energy. Plasma incident region is meshed by keeping elemental size equal to one tenth of entire plasma radius, so that exact ten elements can be fitted. Identified elements were thermally loaded by applying element wise different temperatures for getting more accurate temperature distribution profile. This profile was found to be having crater shape matching with earlier Finite Element Models (FEM) available in the literature. Along with the shape, it also helps to decide the elements having temperatures greater or equal to melting point leading to estimate Material Removal Rate (MRR). Later on single spark MRR can be used to estimate multi-discharge-MRR by calculating pulse rate. Model MRR is validated with the experimental MRR which show a very good agreement, but little variation. This variation in the modeling could possibly due to assumptions like no delay in ignition, non-deposition of recast layer (100% flushing efficiency), etc. The factors like incomplete flushing of debris and inter-electrode gap arcing cause the variation in machining conditions thus reducing the actual MRR. In the present investigation, the use of dielectric is considered only for convection, but in reality, it acts as an insulator, coolant and also as debris remover. Melting and vaporization of material is the main phenomena for material removal. Dielectric fluid partially removes the molten metal because at the same time, the molten metal is under very high pressure due to plasma channel. Its adhesive property resists the material removal. It is very difficult to incorporate all real effects in the model, however the obtained results in the present study show good agreement between model MRR and experimental MRR within 10% variation.

Kerf width analysis of wire electrical discharge machining of titanium alloy (Ti-6Al-4 V ELI) using response surface method

The wire electrical discharge machining (WEDM) allowed success in the manufacture of the hard, fragile, and materials difficult to cut, especially for electroconductive ceramic materials. In this study, the mathematical models of material removal rate (MRR) and surface roughness (SR) used for the machinability evaluation in the WEDM process of aluminum oxide-based ceramic material (Al2O3 + TiC) have been carried out. The experimental plan adopts the face centered central composite design (CCD). The mathematical models using the response surface methodology (RSM) are developed so as to investigate the influences of four machining parameters, including the peak current, pulse on time, duty factor, and wire speed, on the performance characteristics of MRR and SR. It has been proved that the proposed mathematical models in this study would fit and predict values of the performance characteristics, which would be close to the readings recorded in experiment with a 95% confidence level. The significant parameters that critically affect the performance characteristics are examined.

Wire electrical discharge machining (WEDM) is an advanced non-conventional machining process specifically used for obtaining complex 3D shape objects in hard materials with high accuracy. The present study investigates the effect of various process parameters viz. pulse on time, pulse off time, wire feed and servo voltage on response variables such as cutting speed, material removal rate, kerf width and surface roughness on machining of high carbon high chromium steel. Taguchi's L9 orthogonal array for four factors and three levels has been used for designing the experiment. A novel technique for order preference by similarity to ideal solution (TOPSIS) approach has been applied to select the optimal level of machining parameters. Analysis of variance (ANOVA) has been conducted for investigating the effect of process parameters on overall machining performance. The effectiveness of proposed optimal condition is validated through the confirmatory test. The result of this study highlights that the parameters like pulse on time and servo voltage are significantly influencing to the machining performance.

Attempt has been made to optimise surface roughness (Ra) of cold worked high carbon and high chromium hard die steel (AISI: D2) by wire electrical discharge machining (WEDM) process. In present study fractional factorial design of experiment has been used at two levels to conducted five different sets of experiment. Tan-sigmoid and pure line transfer function-based four layered back propagation artificial neural network (BPANN) approach have been applied to develop a suitable model with six WEDM process input parameters and two output parameters, i.e., Ra and material removal rate (MRR). The effect of input parameters has been analysed by training data for the best model using analysis of variance (ANOVA). The model S2 has been found satisfactory as training correlation coefficient (R2) is 99.2% and adjusted correlation coefficient (Radj)2 is 99.1%. The minimum surface roughness has been found using root mean square error (RMSE) approach.

In recent days, the additive manufacturing process plays a vital role in the production of tool electrodes, which are used in the electrical discharge machining (EDM) process. In this work, the copper (Cu) electrodes prepared using the direct metal laser sintering (DMLS) process are used for the EDM process. The performance of the DMLS Cu electrode is studied by machining the AA4032-TiC composite material using the EDM process. Then the performance of the DMLS Cu electrode is compared with the conventional Cu electrode. Three input parameters, such as peak current (A), pulse on time (s), and gap voltage (v), are selected for the EDM process. The performance measures, which are determined during the EDM process, are material removal rate (MRR), tool wear rate, surface roughness (SR), microstructural analysis of machined surface, and residual stress. At a higher pulse on time, more material was removed from the workpiece surface and thus MRR is enhanced. Likewise, at a higher peak current, the SR is amplified and thus wider craters are formed on the machined surface. The residual stress on the machined surface has influenced the formation of craters, microvoids, and globules. Lower SR and residual stress are attained by using DMLS Cu electrode, whereas MRR is higher when using conventional Cu electrode.

Metal matrix composites have become a vital concern for the modern manufacturing companies due to some of their special properties. The presence of reinforcement makes them difficult in machining operations to achieve industrial requirements. Therefore, it is necessary to optimize the machining process parameters to improve output performance in terms of product quality. The overall performance of the wire electrical discharge machining (WEDM) process is influenced by various parameters, such as pulse-on time, pulse-off time, induced current, and wire-feed. WEDM is one of the non-traditional machining processes. It machines only electrically conducting materials and machines the surfaces by the thermo-electrical process. During machining of composites, material removal rate, cutting speed, and surface roughness have been considered for this research. The relation between the process parameters and the output responses is developed by using linear regression analysis through Minitab-17. The experiments conducted are dependent on Taguchi $${\hbox {L}}_{25}$$ orthogonal array. The optimized sets of process parameters are obtained by using teaching and learning-based optimization.

Wire Cut Electrical Discharge Machining (WEDM) is a non-conventional thermal machining process which is capable of accurately machine alloys having high hardness or part having complex shapes that are very difficult to be machined by the conventional machining processes. The WEDM finds applications in automobiles, aero–space, medical instruments, tool and die industries, etc. The input parameters considered for WEDM are pulse on time, pulse off time, flushing pressure, servo voltage, wire feed rate and wire tension. Performance of WEDM is mainly assessed by output variables such as, material removal rate (MRR), kerf width (Kw) and surface roughness (Ra) of the work piece being machined. Looking at the need of a suitable optimization model, the present work explores the feasibility of machine learning concepts to predict optimum surface roughness and kerf width simultaneously by making use of experimental data available in the literature for machining of Hastelloy C– 276 using WEDM. In most of the literatures, single objective optimization has been carried out for predicting optimum cutting parameters for WEDM. Hence, the present work presents a methodology that makes use of a machine learning algorithm namely, gradient descent method as an optimization technique to optimize both surface roughness and kerf width simultaneously (multi objective optimization) and compare the results with the existing literatures. It was observed that the input parameters such as pulse on time, pulse off time, and peak current have significant effect on both surface roughness and kerf width. The gradient descent method was successfully used for predicting the optimum values of response variables.

A review on various methods to improve process capabilities of electrical discharge machining process

Results of applying the wire Electrical Discharge Machining (EDM) process to generate precise cylindrical forms on hard, difficult-to-machine materials are presented. The design of an underwater rotary spindle is first introduced. The spindle is added to a conventional two-axis wire EDM machine to enable the generation of free-form cylindrical geometry. Mathematical models for material removal rate and surface finish in cylindrical wire EDM of the free-form cylindrical workpiece are derived. Experiments are conducted for cylindrical and 2D wire EDM of brass and carbide work-materials. Comparing to the conventional 2D wire EDM of the same work-material, higher maximum material removal rates could be achieved in the cylindrical wire EDM. The surface finish and roundness of parts generated by cylindrical wire EDM at different part rotational speeds and wire traverse speeds are measured and analyzed.