PAPR analysis for OFDM visible light communication.

Visible light communication (VLC) is a technology that is currently being employed to achieve high data rates. Orthogonal frequency division multiplexing (OFDM) is a powerful scheme for intensity modulation and direct detection (IM-DD) that is becoming increasingly important. OFDM systems based on VLC are accomplished through the implementation of IM-DD constraints, including direct current biased optical OFDM (DCO-OFDM), asymmetrically clipped optical OFDM (ACO-OFDM), and asymmetrically clipped DC-biased (ADO-OFDM), among others. The OFDM technique based on VLC is inefficient in terms of spectral efficiency and has a high peak to average power ratio (PAPR). In this article, the symbol time compression-image adjust (STC-IMADJS) technique will be proposed for throughput maximization and PAPR reduction in the DCO-OFDM, ACO-OFDM, and ADO-OFDM systems. Furthermore, the STC technique enables the simultaneous transmission of two sub-carriers through Walsh spreading codes without inference between them. As a result, the OFDM symbol has been reduced by 50%. The IMADJS strategy reduces the high PAPR of transmitted signals by compressing large signals and expanding small signals, as long as the average power level remains constant after compression. Therefore, the proposed STC-IMADJS technique doubles the throughput as well as significantly reduces the PAPR for OFDM systems based on VLC. The simulation results are performed using Matlab-2021a for 1024 sub-carriers. As a result, the simulation results show that the proposed technique reduces the PAPR by 3.7 dB (86%), 8.16 dB (93%), and 1.81 dB (20%) for DCO-OFDM, ACO-OFDM, and ADO-OFDM systems respectively. Furthermore, the technique has a significantly lower computational complexity than conventional OFDM systems based on VLC. Finally, the measures of performance through this article are bit error rate and complementary cumulative distribution function.

Orthogonal frequency division multiplexing (OFDM) has been considered for\nvisible light communication (VLC) thanks to its ability to boost data rates as\nwell as its robustness against frequency-selective fading channels. A major\ndisadvantage of OFDM is the large dynamic range of its time-domain waveforms,\nmaking OFDM vulnerable to nonlinearity of light emitting diodes (LEDs). DC\nbiased optical OFDM (DCO-OFDM) and asymmetrically clipped optical OFDM\n(ACO-OFDM) are two popular OFDM techniques developed for the VLC. In this\npaper, we will analyze the performance of the DCO-OFDM and ACO-OFDM signals in\nterms of error vector magnitude (EVM), signal-to-distortion ratio (SDR), and\nachievable data rates under both average optical power and dynamic optical\npower constraints. EVM is a commonly used metric to characterize distortions.\nWe will describe an approach to numerically calculate the EVM for DCO-OFDM and\nACO-OFDM. We will derive the optimum biasing ratio in the sense of minimizing\nEVM for DCO-OFDM. Additionally, we will formulate the EVM minimization problem\nas a convex linear optimization problem and obtain an EVM lower bound against\nwhich to compare the DCO-OFDM and ACO-OFDM techniques. We will prove that the\nACO-OFDM can achieve the lower bound. Average optical power and dynamic optical\npower are two main constraints in VLC. We will derive the achievable data rates\nunder these two constraints for both additive white Gaussian noise (AWGN)\nchannel and frequency-selective channel. We will compare the performance of\nDCO-OFDM and ACO-OFDM under different power constraint scenarios.\n

In this paper, we present a new form of orthogonal frequency division multiplexing (OFDM) for intensity modulated direct detection (IM/DD) systems. This new form of OFDM uses asymmetrically clipped optical OFDM (ACO-OFDM) on the odd frequency subcarriers and DC biased optical OFDM (DCO-OFDM) on the even subcarriers. By using a form of interference cancellation both the ACO-OFDM and the DCO-OFDM signals can be recovered at the receiver. It is shown that the DCO-OFDM component causes no interference on the odd frequency subcarriers so the receiver processing for the ACO-OFDM signal is identical to a conventional ACO-OFDM system. The ACO-OFDM signal causes clipping noise which falls on the even subcarriers. However, this interference can be estimated and cancelled at the receiver. The cancellation process results in a 3 dB noise penalty in the DCO-OFDM component. Simulation results are presented for an additive white Gaussian noise channel and it is shown that the new technique can achieve better optical power performance than the conventional schemes.

DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) has been proposed in visible light communication (VLC) to overcome the limited modulation bandwidth of light emitting diode (LED). Due to the implementation of the inverse fast Fourier transform at the DCO-OFDM transmitter, DCO-OFDM suffers from its high peak-to-average power ratio (PAPR), which restricts its use in some VLC applications, especially where the optical power efficiency is a crucial requirement. That is because the LEDs used in VLC systems have a limited optical power-current linear range. To this end, a novel discrete Fourier transform spread-optical pulse amplitude modulation (DFTS-OPAM) signal scheme based on the single carrier-interleaved frequency division multiple access (SC-IFDMA) signal is introduced in this paper to address the high PAPR issue of OFDM. DFTS-OPAM is achieved by considering a PAM as an SC-IFDMA data symbol and duplicate the output vector of the fast Fourier transform at the SC-IFDMA transmitter side. Simulation results show that the PAPR of the proposed scheme is 7 dB lower than that of DCO-OFDM. Furthermore, this significant PAPR improvement is experimentally investigated where the practical results show that the proposed scheme can provide more 2.5 dB reduction in the average transmitted power requirement compared to DCO-OFDM and can subsequently increase the maximum achieved distance between the transmitter and the receiver up to 44%.

Visible light communication (VLC) is now used to achieve high data rates. Opticalorthogonal frequency division multiplexing (O-OFDM) is a strong technique for intensity modulation and direct detection (IM-DD). Direct current biased O-OFDM (DCO-OFDM) and asymmetrically clipped O-OFDM are two modern O-OFDM systems that operate with IM-DD constraints (ACO-OFDM). Due to severe out of band interference, the DCO-OFDM and ACO-OFDM systems have a high peak to average power ratio (PAPR) and substantial adjacent channel interference (ACI) (OOB). Furthermore, as compared to bipolar OFDM systems, they obtain a greater chance of bit error. The combination of the STC scheme, symbol extension, and pulse shaping signal is presented in this paper for improving the performance of the O-OFDM system without affecting system throughput. This article also decreases the OOB, PAPR, and bit error rate (BER) of DCO-OFDM and ACO-OFDM systems. Further analytical analyses for the proposed systems, such as OOB, PAPR, and computing complexity, are obtained in this paper. The simulation results verify the analytical study of the proposed methods for OOB reduction and PAPR reduction. As compared to typical O-OFDM systems, the proposed shaped STC-DCO-OFDM scheme and the proposed shaped STC-ACO-OFDM scheme lower the OOB by about 40 dB and the PAPR by about 4 dB at the 10 -3 probability point of the complementary cumulative distribution function (CCDF). The proposed systems outperform existing O-OFDM systems under AWGN for the BPSK modulation scheme in terms of BER, and reduce the computational complexity.

As a promising modulation technology for optical communication, Orthogonal Frequency Division Multiplexing (OFDM) is now increasingly used and a lot of ways of improving the optical efficiency of Intensity Modulated/ Direct Detection (IM/DD) systems have been proposed. And real and non-negative OFDM signals are required in this kind of system. Asymmetrically clipped DC biased Optical OFDM (DCO-OFDM), Asymmetrically Clipped Optical OFDM (ACO-OFDM) and Asymmetrically clipped DC biased Optical OFDM (ADO-OFDM) can satisfy this requirement. In this paper, we analysis the properties and performance orderly of the above three systems and simultaneously compare their performance. The simulation results show that DCO-OFDM is efficient in terms of bandwidth while the ACO-OFDM is efficient in terms of optical power. More importantly, ADO-OFDM is both power-efficient and bandwidth-efficient. At the same time, a developmentally proposal for the future OFDM in IM/DD systems is put forward.

This paper analyzes the performance of indoor orthogonal frequency division multiplexing (OFDM) optical wireless communication systems in the presence of light emitting diode (LED) nonlinear distortions. There are several forms of optical OFDM using intensity modulation [7th Int. Symp. on Communication Systems Networks and Digital Signal Processing (CSNDSP), 2010, pp. 566-570]. In this paper, DC-biased optical OFDM (DCO-OFDM) and asymmetrically clipped optical OFDM (ACO-OFDM) are considered. ACO-OFDM produces a half-wave symmetry time signal at the output of the OFDM modulator by special assignment of subcarriers, thus allowing signal clipping at the zero level and avoiding the need for DC bias at the expense of data rate reduction. DCO-OFDM assigns data to all possible subcarriers to increase the data rate. However, half-wave symmetry signals cannot be achieved and a high DC bias is needed to convert the bipolar signal to a unipolar signal before modulating the LED intensity. This paper considers a practical LED model and studies the performance of both systems in terms of average electrical OFDM signal power versus bit error ratio in the presence of an additive white Gaussian noise (AWGN) channel. In addition, DC power consumption and the transmitted optical power for the two systems are compared. The analytical results are validated through Monte Carlo simulations and the obtained results demonstrate close match. It is shown that LED clipping has significant impact on the performance of both systems and an optimum system design should take into account the OFDM signal power, DC-bias point, and LED dynamic range.

Visible light communication (VLC) is a promising and viable optical wireless communication (OWC) system that utilizes light-emitting diodes (LEDs) to achieve high data rates, energy efficiency, and resistance to electromagnetic interference (EMI). Direct-current biased optical orthogonal frequency division multiplexing (DCO-OFDM) is a widely used scheme in VLC due to its high spectral efficiency. However, it suffers from significant challenges related to its elevated peak-to-average power ratio (PAPR), which causes nonlinear distortion and signal clipping due to LED limitations. To address this issue, this paper proposes a combination of Vandermonde-like matrix (VLM) precoding and nonlinear companding transform (NCT) techniques (specifically A-law and μ-law) over DCO-OFDM-based VLC. The VLM precoding minimizes the autocorrelation of the OFDM signal, hence reducing its PAPR, and NCT compresses the dynamic range of the signal. Simulation results indicated that the hybrid techniques achieved a PAPR reduction of around 3.5 dB (by 76 %); this is in the best case reduction compared to the conventional DCO-OFDM while maintaining an acceptable bit error rate (BER), moderately higher signal-to-noise ratio (SNR) is required.

In this paper, a multivariate regression transform (MRT) is proposed for pulse-amplitude-modulated-based hybrid optical orthogonal frequency division multiplexing (PHO-OFDM) visible light communications (VLC). PHO-OFDM is a hybrid modulation scheme that combines pulse amplitude modulated discrete multitone (PAM-DMT) and DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) for simultaneous transmission. The proposed method reduces the peak-to-average power ratio of PHO-OFDM to improve its system performance. Complementary cumulative distribution function simulation results show that the proposed method can effectively mitigate the PAPR of PHO-OFDM under different constellation combinations.

The dual functionality of assuring ‘illumination’ and “communication” contemporaneously by relying on sustainable and energy-efficient opto-electronic devices like light emitting diodes (LEDs) has enabled visible light communication to garner the attraction of research era. This paper proposes a discrete sine transform (DST)-based optical orthogonal frequency division multiplexing (OFDM) system bestowing as the simplest and alternative multicarrier scheme complying the requirements of intensity modulated and direct detection systems. Moreover, this paper addresses the most vital issue like peak to average power ratio (PAPR) that emerges principally due to the limited dynamic range of LEDs when exploiting DC-biased optical OFDM (DCO-OFDM). Therefore, this paper imparts DST spreading to DST-based DCO-OFDM (DST-S-DCO-OFDM), and consequently, the PAPR performance is compared with other PAPR reduction schemes for the same system. Furthermore, in order to serve multiple subscribers with high-data rates as well as to significantly reduce the amount of PAPR of the multicarrier system, this work investigates a DST-based single carrier frequency division multiple access (DST-SC-FDMA) and derives the mathematical analysis of the time-domain signal formats for different subcarrier mapping strategies like DST-based optical interleaved frequency division multiple access (DST-OIFDMA) and optical localized frequency division multiple access (DST-OLFDMA). The simulated results evidences that the reduction in PAPR for DST-S-DCO-OFDM is more predominant when compared with other PAPR reduction schemes and among the multiple access schemes, the DST-OIFDMA is more power efficient upon comparison with DST-OLFDMA. However, both the schemes exhibit a significant reduction in PAPR when compared with DST-based optical OFDM (DST-OOFDMA).

In this paper, we present a novel 3B/4B coding scheme for the reduction of peak-to-average power ratio (PAPR) in the orthogonal frequency division multiplexing (OFDM) communication system. In the proposed technique, we apply the encoding in the time domain of the OFDM transmitter to redistribute the power distribution of each transmitting signal samples. PAPR of the OFDM signal at the CCDF (Complementary Cumulative Distribution Function) of 10-5 can be reduced to about 11, 15 and 17 dB for N = 16, 64, and 256 respectively by applying the proposed scheme. Our analysis also shows that the proposed method would have bounded PAPR as the number of OFDM subcarriers N approaches infinity. Moreover, the method has very low complexity and the complexity does not increase as the number of OFDM sub-carriers increases. The proposed scheme also has error correction capability to reduce bit error rate (BER) at the same time.

Iterative receiver for ADO-OFDM with near-optimal optical power allocation

An analytical investigation on the impact of the DC bias on the clipping noise and the laser non-linearity in Asymmetrically Clipped Optical Orthogonal Frequency Division Multiplexing (ACO-OFDM) and Direct Current--Biased Optical OFDM (DCO-OFDM) is performed. Clipping noise in the OFDM system is introduced either by transmitter non-linearity or due to the low power sensitivity of the receiver. However the clipping noise in the DCO-OFDM is also dependent upon the DC bias applied to make the bipolar OFDM signal unipolar. The addition of this extra DC bias increases the average signal power of the DCO-OFDM signal. The non-linearity of the DFB laser increases with the optical modulation index, which gives rise to intermodulation and harmonic distortions at the receiver. The OFDM signal when transmitted through the Single Mode Fiber (SMF) suffers from group--velocity dispersion (GVD) which limits its performance in the Passive Optical Networks (PON). In this paper, an assessment of the DC bias to reduce the clipping noise in the two systems under consideration is performed. A practical laser model is considered and analysis is performed to estimate the average laser drive power to maintain its non-linearities within a tolerable region for both the OFDM systems. A simulation is performed to transmit 5 and 8 Gb/s (ACO and DCO) OFDM signal over 120 km SMF where the effect of GVD is taken into consideration. An optimum OFDM drive signal power is calculated to maintain the laser transmitter in its linear region such that the effect of second order harmonic distortions (HD2) and third order intermodulation distortion (IMD3) is low. The SNR requirement of DCO-OFDM being higher than the ACO-OFDM leads to more clipping noise, HD2 and IMD3.

In this paper, several Orthogonal frequency division multiplexing (OFDM)-based Visible light Communications (VLC) techniques designed for intensity modulation/direct detection (IM/DD) are evaluated and compared for various optical channels. Evaluations are done for line-of-sight (LOS) and no-line-of-sight (NLOS) channels. The techniques analyzed are asymmetrically clipped optical OFDM (ACO-OFDM), direct-current (DC) biased optical OFDM (DCO-OFDM), and asymmetrically clipped DC biased optical OFDM (ADO-OFDM). These schemes are evaluated and compared for different M-QAM modulations in terms of bit error rate (BER). It is shown that ACO-OFDM, in general terms, presents a better performance compared to the conventional DCO-OFDM and ADO-OFDM schemes.

PAPR reduction of asymmetrically clipped optical OFDM signals: Optimizing PTS technique using improved flower pollination algorithm