PAPR Reduction with Compressive Sensing for Joint Radar and Communication System

Orthogonal Frequency Division Multiplexing (OFDM) is a multicarrier modulation technique that has been widely applied in wireless broadband communications such as the fourth-generation (4G) and supports the development of the fifth-generation (5G) technology because it is efficient and effective. However, OFDM has a high Peak to Average Power Ratio (PAPR) value where the system must use a Power Amplifier (PA) with a high linear range so that the signal can work on PA. Whereas, PA is a nonlinear component that has limited linear region according to the component specifications. If an OFDM signal with high PAPR passes through the nonlinear region of PA, the signal will be distorted nonlinearly and ultimately worsen the OFDM performance. Although many researchers are interested in studying this issue, several scenarios are still not explored. This work investigates a way to mitigate nonlinear distortion by a combination of PAPR reduction and PA linearization with predistortion. Memory-Hammerstein has been suggested as a model for predistorter and PA. The input of the predistorter is the PAPR reduced signal with companding technique, which is a simple and effective PAPR reduction technique for OFDM. The system performance will be evaluated using signal spectrum, PAPR, and Bit Error Rate (BER). The simulation results obtained are that the performance drops dramatically to more than 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−1</sup> for the BER value when a nonlinear disturbance is given and the performance improves after a predistorter is applied. The combination of hybrid companding and predistorter offers better performance, it can reduce PAPR and compensating for nonlinear distortions caused by the PA. Hence, this combined scheme can be considered and adopted in future wireless communications systems including 5G.

Orthogonal frequency division multiplexing (OFDM) signals have a generic problem of high peak to average power ratio (PAPR) which is defined as the ratio of the peak power to the average power of the OFDM signal. The drawback of the high PAPR is that the dynamic range of the power amplifiers (PA) & digital-to-analog (D/A) converters required during the transmission and reception of the signal is higher. As a result, the total cost of the transceiver increases, with reduced efficiency. This paper includes an idea of the PAPR constraint, along with the implementation and analysis of some specific algorithms for PAPR reduction of the OFDM signals. All the PAPR reduction algorithms are implemented and tested in the OFDM transceiver designed using Matlab. Analyzing some specific algorithms, we propose a novel algorithm by combining the subcarrier phase adjustment and linear combination of the time domain OFDM signals. Simulation results for a OFDM system employing Quadrature Amplitude Shift Keying (QASK) symbols and Quadrature Amplitude Modulation (QAM) can achieve a PAPR reduction of 5 dB.

Requirement of high data rate by the modern mobile communication system requires a linear power amplifier with extremely low power consumption and long battery life. Orthogonal frequency division multiplexing (OFDM) modulation technique promises to deliver high data rate with simple receiver structure. It is more spectral efficient and has been recommended to be used by many standards. But it has one major disadvantage of having high peak to average power ratio (PAPR). High PAPR drives the power amplifier in saturation region and causes it to operate in nonlinear region with reduced efficiency. There are several techniques to reduce PAPR of OFDM system. In this paper we have done FPGA implementation of selective mapping method (SLM) for PAPR reduction for 4 QAM baseband signal for 64, 128, 256, 512 and 1024 number of subcarriers. The result obtained have been compared with PAPR values obtained through mathematical analysis and Matlab simulations and also with original signal. For 1024 number of subcarriers at 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> of CCDF value the PAPR value obtained with hardware implementation is 9.8 dB which is 2.8 dB less form the original OFDM signal obtained without applying SLM technique but 0.9 dB higher than the Matlab simulated value. This technique is simple in implementation, utilizes less resources and is effective in PAPR reduction.

Towards Optimal Mimo-Ofdm Waveforms : A Low-Papr Transmission Strategy With Artificial Neural Networks

OFDM (orthogonal frequency division multiplexing) is usefully applied for DAB (digital audio broadcasting) and DVB (digital video broadcasting) systems due to its high spectral efficiency and robustness to ISI (intersymbol interference) and multipath fading. However, the OFDM signal has a large PAPR (peak-to-average power ratio), which results in significant nonlinear distortion when it passes through an HPA (high power amplifier) such as a TWTA (traveling wave tube amplifier) and a SSPA (solid state power amplifier). We propose a new PAPR reduction method using soft clipping and filtering. Unlike conventional hard clipping, soft clipping has non-zero slope in the clip region. Next, filtering, which uses additional FFT and IFFT processes, is applied in order to reject the out-of-band clip noise. Although the filtering removes the out-of-band noise, it oppositely increases PAPR by a small amount. Since an HPA increases the power consumption according to the linearity range, soft clipping for an SSPA lowers power consumption and is more efficient than the conventional hard clipping method. By the results of the proposed method, the wanted PAPR can be obtained and there is no out-of-band radiation caused by the clipping process.

In this paper, we propose a new PAPR reduction by using a partial transmit sequences (PTS) method with coded side information (SI) technique. These methods are used in an orthogonal frequency division multiplexing (OFDM) system. The OFDM employs orthogonal sub-carriers for data modulation. These sub-carriers unexpectedly present a large peak to average power ratio (PAPR) in some cases. In order to reduce PAPR, the sequence of input data is partitioned into disjoint sub-block of PTS. If number of sub-block increases, high efficiency of PAPR reduction can be obtained. However, a quite large calculation cost must be demanded and thus it is impossible to obtain the optimum PTS. In the proposed method, we introduce a coded side information technique assuming the pseudo-optimum condition into the PTS. The total calculation cost becomes drastically reduced and side information bits for recovering original data in demodulation. In simulation results, the proposed method demonstrated the improvement of PAPR and bit error rate (BER) performance.

In this paper, we propose a novel peak to average power ratio (PAPR) reduction scheme of orthogonal frequency division multiplexing (OFDM) signals. In our proposed scheme we exploit the repeated rotation and recombination of the in-phase and the quadrature components of an OFDM symbol in time domain. Our proposed scheme has two main advantages over the previously known scheme such as iterative partial transmit sequence (I-PTS), which are 1) remarkably lower computational complexity and 2) less required side information overhead than the I-PTS scheme. Based on our derived complementary cumulative distribution (CCDF) of PAPR, we show that our proposed scheme gives only 0.2 - 0.3 dB loss compared to the I-PTS scheme in terms of PAPR threshold while the complexity for the implementation is much reduced. Furthermore, the proposed scheme does not cause any loss of bit error rate performance over both the additive white Gaussian noise (AWGN) channel and the frequency selective channel even though the simulation results regarding the bit error rate (BER) performance is not shown in this paper due to the limited space of the pages.

In this paper, tone injection (TI) based on differential evolution algorithm (DE) is proposed to reduce the peak-to-average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals. TI is a distortionless PAPR reduction technique, but its high search complexity for finding optimal TI scheme requires an exhaustive search over all combinations of possible permutations of the expanded constellation, which is a potential problem for practical applications. In this work we present a novel convex optimization approach to numerically determine the near-optimal tone injection (TI) solution based on a differential evolution algorithm (DETI). DETI is compared to different TI schemes for PAPR reduction and search complexity performances. The simulation results show that the proposed DETI method provides good PAPR reduction and bit error-rate (BER) performances. Finally, the DETI algorithm not only reduces the PAPR significantly, but also decreases the computational complexity. The simulation results show that it achieves more or less the same PAPR reduction as that of exhaustive search.

Orthogonal Frequency Division Multiplexing (OFDM) has several desirable attributes, such as high immunity to inter-symbol interference, robustness with respect to multi-path fading, and ability for high data rates, all of which are making OFDM to be incorporated in wireless standards like IEEE 802.11a/g/n WLAN and ETSI terrestrial broadcasting. However one of the major problems posed by OFDM is its high Peak-to-Average-Power Ratio (PAPR), which seriously limits the power efficiency of the transmitter’s High Power Amplifier (HPA). This is because PAPR forces the HPA to operate beyond its linear range with a consequent nonlinear distortion in the transmitted signal. One of good solutions to mitigate this nonlinear distortion is put a Pre-Distorter before the High Power Amplifier and increase linear dynamic range up to a saturation region (1) (2) (3). However, the main disadvantage of Pre-Distorter technique is that these PD techniques only work in a limited range, that is, up to the saturation region of the amplifier. In this situation, Peak-to-Average Power Ratio (PAPR) reduction techniques which pull down high PAPR of OFDM signal to an acceptable range can be a good complementary solution. Due to practical importance of this, there are various PAPR reduction techniques for OFDM signals (4) (5) (6) (7) (8) (9). Among them, the PTS (Partial Transmit Sequence) technique is very promising because it does not give rise to any signal distortion (9). However, its high complexity makes it difficult to use in a practical system. To solve the complexity problem of the PTS technique, Cimini and Sollenberger proposed an iterative flipping algorithm (10). Even though the iterative flipping algorithm greatly reduces the complexity of the PTS technique, there is still some performance gap between the ordinary PTS and the iterative flipping algorithm. In this chapter, we propose an enhanced version of the iterative flipping algorithm to reduce the performance gap between the iterative flipping algorithm and the ordinary PTS technique. In the proposed algorithm, there is an adjustable parameter to allow a performance/complexity trade-off.

In this paper, we propose a new peak-to-average power ratio (PAPR) reduction technique, which is referred to as trellis-assisted constellation subset selection ( TACSS , or TAX for short), for orthogonal frequency-division multiplexing (OFDM) signals. We control the signal transition by judiciously selecting the appropriate constellation subset for PAPR reduction with the controlling bits that are subject to the trellis-based constraint imposed by a bank of memories. A novel constellation design suitable for the proposed system is also introduced. A major property offered by the proposed approach is that the controlling bits and the information bits are perfectly separable at the receiver, which leads to a simple implementation of its soft-in–soft-out (SISO) decoder for coded OFDM systems. Through the performance analysis of PAPR reduction capability, power amplifier (PA) efficiency, average mutual information (AMI), and bit error rate (BER), the achievable tradeoff relationship between the transmitter and receiver performances of the proposed system is addressed. Furthermore, performance comparisons of the proposed scheme with other major PAPR reduction schemes such as trellis shaping, discrete Fourier transform (DFT) precoding, and clipping and filtering demonstrate its practical advantage in a high-spectral-efficiency regime.

This paper proposes an enhancement to a previously reported adaptive peak-to-average power ratio (PAPR) reduction method based on clipping and filtering (CF) for eigenmode multiple-input multiple-output (MIMO) - orthogonal frequency division multiplexing (OFDM) signals. We enhance the method to accommodate the case with adaptive modulation and channel coding (AMC). Since the PAPR reduction process degrades the signal-to-interference and noise power ratio (SINR), the AMC should take into account this degradation before PAPR reduction to select accurately the modulation scheme and coding rate (MCS) for each spatial stream. We use a lookup-table-based prediction of SINR after PAPR reduction, in which the interference caused by the PAPR reduction is obtained as a function of the stream index, frequency block index, clipping threshold for PAPR reduction, and input backoff (IBO) of the power amplifier. Simulation results show that the proposed PAPR reduction method increases the average throughput compared to the conventional CF method for a given adjacent channel leakage power ratio (ACLR) even when we assume AMC.

High Peak-to-Average Power Ratio (PAPR) of the Orthogonal Frequency Division Multiplexing (OFDM) signal is one of the limitations to the transmission performance of optical OFDM system. In this paper, we propose a novel hybrid PAPR reduction technique called Hadamard Transform Combined with Partial transmit sequence (HTCP). The proposed HTCP scheme combines the merits of two complementary techniques, i.e., Hadamard transform and Partial Transmit Sequence (PTS), to improve the performance of the optical OFDM system in terms of PAPR and Bit Error Rate (BER). Simulation results show that the HTCP scheme has better performance with regard to PAPR and BER compared with the case of applying only the Hadamard transform or PTS technique.

High peak to average power ratio (PAPR) of the transmitted signal is a major drawback of multicarrier transmission such as orthogonal frequency division multiplexing (OFDM). This work considers the problem of PAPR reduction in a multi-symbol encapsulated OFDM (MSE-OFDM) system. This paper employs the discrete cosine transform (DCT) to the data sequence. Not only can this method have the same bandwidth efficiency as that of the CP-reduced MSE-OFDM system, but also reduce the PAPR in the MSE-OFDM. Simulation shows that the proposed scheme can significantly reduce the PAPR in MSE OFDM system without increasing the symbol error rate.

We propose a clipped companding scheme to effectively reduce PAPR (peak-to-average power ratio) of OFDM (orthogonal frequency division multiplexing) signals. The proposed scheme is based on the companding to take both complexity and BER (bit error rate) performance into account, and composed of the clipping followed by the companding. In the first step of the proposed scheme, some peak signals which do not influence the BER, are clipped. In the second step, the proposed scheme utilizes the mu-law companding to effectively reduce the PAPR Simulation results show that the proposed scheme provides more PAPR reduction without degradation of the BER performance as compared to the conventional mu -law companding.

Multicarrier modulation technique also known as Orthogonal Frequency Division Multiplexing (OFDM) is considered to be the most rapidly growing technique for 4th Generation wireless communication system. Due to its high speed data rate and its ability of multipath fading channel robustness. OFDM becomes an attractive technique and it is widely adopted in many wireless communications system. OFDM signal carries its major drawback of high Peak to Average Power Ratio (PAPR) problem. Out of band radiation and in band distortion produced due to its high PAPR. Mobile phone communication suffer severe drawback during its amplification. When OFDM employed a non linear Power Amplifier (PA), it produces the fluctuation in amplitude of OFDM signal. This paper discusses the method to overcome PAPR in terms of its performance by using improved clipping technique for PAPR reduction. This method is easy to implement and reduces the amount of PAPR by clipping the peak of the maximum power signal. We present an improved method for PARR reduction for reducing peak magnitude of OFDM signal. This scheme simultaneously minimizes the peak magnitude of PAPR in OFDM signal.