Parallel control for electro-hydraulic load simulator using online self tuning fuzzy PID technique

In this paper, model-based precision force and position control of an ionic polymer metal composite (IPMC) is presented. A 23.8 mm × 3.4 mm × 0.16 mm IPMC strip was used as an actuator in a cantilever configuration. Open-loop force and position responses of an IPMC are not repeatable, and hence closed-loop precision control is of critical importance to ensure proper functioning, repeat-ability and reliability. After feedback controllers were designed and implemented with empirically obtained fourth-order plant transfer functions, the overshoot decreased from 460 to 2.8 per cent and the settling time was reduced from 37.5 to 3.22 s in force control. In position control the overshoot decreased from 333 to 20.3 per cent and the settling time was reduced from 21.5 to 2.56 s. Microscale precision force and position control capabilities of the IPMC actuator were also demonstrated experimentally. An 8 μN force resolution was achieved with a force noise of 0.5μN r.m.s., and the position resolution was 6 μm with a position noise of 2.5 μm r.m.s. The maximum force and tip displacement achieved with the IPMC actuator under closed-loop control were 2 mN and 5 mm respectively. The IPMC actuator could follow various commanded force and position trajectories such as sinusoidal and trapezoidal position profiles, and a velocity profile with a 3 mm/s maximum velocity. A novel hybrid force and position control strategy demonstrated its utility in practical micromanipulalion applications where the actuator force must be limited to prevent damaging micro-objects. High-precision control of the IPMC at low force level proved its potential for micromanufacturing and micromanipulation applications such as robotic and biomedical microgrippers.

The learning control is applied to hybrid force and position control of robot manipulators. When the geometry and position of a constraint surface is known, the hybrid force and position controller and the feedforward compensator can be designed in the constraint coordinates. When the operation is periodic, the learning hybrid force and position control enhance the control performance as the feedforward compensator is updated in each cycle by the force and position error in the preceding trials. This scheme is proved to be asymptotically stable. A two degree of freedom SCARA-type direct-drive robot manipulator is used to test the learning hybrid force and position control. The deburring tool mounted on the upper link of the robot could follow a flat, tilted flat, and curved 1/4 " aluminum plate with a desired contact force of 10 N (within the root-mean-square force error of 1.95 N) and with a desired tangential velocity. The experiments confirmed the effectiveness of the learning hybrid force and position controller.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

This paper proposes an intelligent massage control system by using multi-fingered robot hand with hybrid impedance and force control, which is able to create the movement and force of robot to behave as similar as the human’s massage. Therefore, the various massage points, such as the changing of hardness and softness of human skin muscle condition, can be appropriately controlled by using hybrid impedance and force control method. The impedance control is used to control the lateral position of massage on the human skin muscle. The perpendicular direction one, while force control is carried out for the vertical direction on human skin muscle. This paper also gives a modeling of human skin muscle through robot perception of impedance to decide the parameter of impedance controller. The control strategy using a hybrid impedance and force control to implement an adaptive control system is presented, when human condition is changed with soft and hard skin muscle. For the robot fingertip force, PI servo compensation is used together with impedance control. Based on using both impedance and PI servo compensation, the effectiveness of the massage position and force control is shown through actual massage motion experiments.

There are many tasks which require robotic manipulators interaction with environment. It consists of three control problems, i.e., position control, impact control and force control. The position control means the way of reaching to the environment. The moment of touching to the environment yields the impact control problem and the force control is to maintain the desired force trajectory after the impact with the environment. These three control problems occur in sequence, so each control algorithm can be developed independently. Especially for redundant manipulators, each of these three control problems has been important independent research topic. For example, joint torque minimization and impulse minimization are typical techniques for such control problems. The three control problems are considered as a single task in this paper. The position control strategy is developed to improve the performance of the task, i.e., minimization of the individual joint torques and impulse. Therefore, initial conditions of the impact control problem are optimized at the previous position control algorithm. Such a control strategy yields improved result of the impact control. Similarly, the initial conditions for the force control problem are indirectly optimized by the previous position control and impact control strategies. The force control algorithm uses the individual joint torque minimization concept. It also minimizes the force disturbances. The simulation results show the proposed control strategy works well.

The paper proposes a feedback force and velocity control of an arm exoskeleton to assist user motion. The original published control so-called feedback hybrid force and position control was based on the force and position control and was designed to assist user motion. This original control was successful at providing assist for the user’s arm. This article presents an improved control scheme called the feedback force and velocity control. The proposed control is designed to regulate the velocities of joints of the exoskeleton and the feedback forces on links to assist user motion. The design and optimization of the feedback force and velocity control are realized by the Balancing Composite Motion Optimization (BCMO). The numerical method is realized in the paper to show that the proposed control is better than the original control in terms of less oscillation and fast response.

In this study, the displacement and blocking force of the tip point of a cantilevered electro-active polymer (EAP) actuator has been controlled for a cell injection process which consists of approaching, interacting and leaving steps. A vision-based system is used to acquire the tip displacement data for identifying a transfer function model of the actuator and its position control. Discrete time Proportional-Integral controllers are used to control the position and blocking force. A Smith Predictor is utilized in the vision-based position control system to compensate for the time delay due to image processing. Experimental position and blocking force results prove that the proposed control strategies are effective enough to guide the actuator to undertake the cell injection process. This study contributes to the previously published work from the point of view of simultaneously controlling the position and blocking force of the electroactive polymer actuators and widening their application areas.

The best exoskeleton control strategy depends on the task, motivating the development and analysis of an exoskeleton capable of position, force, and impedance control. In this paper, we implement and compare the three controller types via sliding mode control on a custom-built pneumatic cylinder ankle exoskeleton. To evaluate each controller's performance, the exoskeleton was tested on the benchtop and with human subject experiments. With the position controller, the exoskeleton achieved an root-mean-square error (RMSE) of under 5 deg for both the benchtop and human tests. It had a bandwidth of approximately 12 rad/s. The force controller tracked sinusoidal trajectories acceptably well at low frequencies (15% of force range at 6 rad/s), with a bandwidth of approximately 24 rad/s. The error was significantly higher (RMSE of 24% of force range) for the more biologically relevant trajectory. The impedance controller demonstrated the desired spring-like behavior, with position RMSE generally under 5 deg compared to expected position. All three controllers worked equally well for benchtop and human tests. Thus, a pneumatically powered ankle exoskeleton with sliding mode control is capable of accurate position and impedance control and is capable of marginally acceptable force control.

Constrained motion of a planar rigid-flexible manipulator is considered in this study. a dynamic model with zero tip deformation constraint of constrained rigid-flexible 608

Position control and vibration control of the underactuated flexible robot in operational space is implemented. Firstly, the dynamic equations in operational space are derived using the assumed modes method. And kinematics and dynamics of the system are analyzed. Secondly, position control method of the underactauted flexible manipulator in the operational space is proposed. Because the elastic vibration of flexible links can not be eliminated only via position control, based on position control strategy, vibration control schemes are presented. The simulation of a 2DOF underactuated flexible manipulator indicates that position and vibration control methods have great effects on increasing end manipulation accuracy, reducing tracking errors and improving dynamic characteristics, which also verifies the validity of control strategies. Thus, for the underactuated flexible robot, both the position control and the vibration control are implemented simultaneously.

Unmanned aerial vehicle (UAV) applications have evolved to a wide range of fields in the last decade. One of the main challenges in autonomous tasks is the UAV stability during maneuvers. Thus, attitude and position control play a crucial role in stabilizing the vehicle in the desired orientation and path. Many control techniques have been developed for this. However, proportional integral derivative (PID) controllers are often used due their structure and efficiency. Despite PID’s good performance, different requirements may be present at different mission stages. The main contribution of this research work is the development of a novel strategy based on a fuzzy-gain scheduling mechanism to adjust the PID controller to stabilize both position and altitude. This control strategy must be effective, simple, and robust to uncertainties and external disturbances. The Robot Operating System (ROS) integrates the proposed system and the flight control unit. The obtained results showed that the proposed approach was successfully applied to the trajectory tracking and revealed a good performance compared to conventional PID and in the presence of noises. In the tests, the position controller was only affected when the altitude error was higher, with an error of 2% lower.

As an electro-hydraulic load simulator (EHLS) is a typical passive force or torque control system, strong motion disturbance has been the key problem. This paper constructs mathematical model of EHLS system and analyzes theoretically the root cause of extraneous torque. A compound control strategy is proposed to improve the loading performance of EHLS. The motion compensation controller based on the extended state observer (ESO) decouples actuator's motion disturbance. And active disturbance rejection control (ADRC) is designed to cope with nonlinearities and uncertainties of EHLS. Simulation is performed to prove the validity of this method in eliminating extraneous torque.

Nonparametric control algorithms for a pneumatic artificial muscle

A kind of nonlinear dynamics model of free-floating dual-arm space robot system is based on Lagrange method, and the dynamics model of object is presented based on Newton-Euler method. Based on the results and closed kinematic chain constraints, the dynamics model of synthetical system is obtained, and the control problems for object to track the desired trajectory in workspace and adjustment of interactive forces due to the interaction between the object and the end-effectors are discussed. Because of the high complexity of structure and the uncertainty of parameter of such systems, the scheme of variable structure global sliding-mode control with better robustness to uncertainty and disturbance is proposed to track the desired trajectory of object, and the corresponded scheme of internal forces control is proposed synchronously. Therefore, the object position and internal forces can be regulated simultaneously. A fuzzy controller is designed to reduce shiver due to the inherent defect of sliding-mode control and ensure rapid response. The fuzzy controller can tune the sliding-mode control law parameters automatically according to the relationship between the system state and switch surface. The effect of the controllers is testified by computer simulation.

To address the demands for precision and load-bearing capacity in the installation of building panels, a hybrid force-position driven robot with redundant actuation has been developed. The mechanical performance of this robot is primarily governed by its central parallel mechanism, which is equipped with redundant actuators matching the degrees of freedom. Non-redundant and redundant actuators are respectively responsible for position and force control. The inclusion of redundant force-driven joints has increased the internal coupling within the mechanism. To enhance the coordination between position and force control, a hybrid synchronized control method based on cross-coupling has been proposed. Initially, kinematic and dynamic models of the parallel structure were established. Under predefined trajectories, the theoretical inputs for each actuator were calculated using inverse kinematics and dynamics. Subsequently, employing the principle of cross-coupling, the torque output from the position actuators was used as feedback. This feedback was processed by a synchronized coordination controller to adjust the output force of the redundant force-driven joints. By adjusting the output force of the redundant actuators, the torque burden on the position actuators was effectively reduced, thereby enhancing the precision of position control. Additionally, under the same load conditions, smaller power actuators could be utilized for position control, reducing the overall weight of the robot and improving its load-to-weight ratio. To validate the effectiveness of the proposed control strategy, a robotic simulation environment was established. The simulation results demonstrated significant reductions in the average torque required by the position actuators across three different trajectories, with reductions of 91.43%, 54.56%, and 80.6% respectively. Finally, the load-bearing capacity and the load-to-weight ratio of the prototype were assessed. Experimental results confirmed that the prototype achieved a load-to-weight ratio of 15.83%, validating the effectiveness of the hybrid synchronized control method based on cross-coupling.

Two different control schemes, position model referenced control (PMRC) and force model referenced control (FMRC), are developed for a simplified two robots model with one interacting axis. The dynamic stability of the position (or force) control under the FMRC (or PMRC) is analyzed. Results indicate that PMRC, although providing better dynamic performance of the position control, may degrade the dynamic performance of the force control. However, FMRC can provide better dynamic performance of both position and force control.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>