Performance evaluation of post quantum digital signature algorithms over WDM optical communication system

Different distortions that affect gridless wavelength division multiplexing (WDM) systems due to nonlinear impairments of the optical fiber and linear interchannel interference (ICI) errors cause signal degradation and a decrease in the transmission system quality. Overcoming these effects is a challenge if there is no information about the source of the distortion. In this work, we propose two asymmetric demodulation methods based on decision tree (DT) algorithms to mitigate distortions associated with linear ICI in gridless WDM systems, even when optical channels are spectrally overlapped. The first method uses the conventional DT and random forest (RDF) algorithms adapted to create asymmetrical thresholds in m-QAM digital demodulation. The second method uses the density-based spatial clustering of applications with a noise (DBSCAN) algorithm, including the K-Dimensional tree (K-D tree) algorithm to treat symbols in boundary conditions. Both methods were experimentally validated in a 3×16GBd gridless Nyquist WDM system modulated in 16-QAM with different channel spacing. DT-based demodulation, including RDF, achieved gains up to ∼1.6dB in the FEC limit 3.8×10−3, while demodulation based on DBSCAN plus the K-D tree achieved gains up to ∼1.2dB compared to conventional demodulation. Additionally, we performed a brief latency analysis in comparison to other previous machine learning-based demodulation methods, where DT and RDF presented latency up to ∼0.3% and ∼32% of the DBSCAN + K-D tree latency, respectively. Finally, the proposed asymmetric demodulation methods can improve the performance of future elastic optical networks by offering easy interpretation of the digital demodulation process and the possibility of adapting them to any m-QAM modulation format being agnostic to signal distortion.

The authors have studied the possibilities to obtain the maximum spectral efficiency for a combined wavelength division multiplexing (WDM) system by minimizing the channel spacing. The fiber optic transmission systems under study can be considered in the context of next generation optical networks and is offered as a model for designing the future backbone networks. In the case of different telecom operators' optical networks merging, in the nearest future the necessity may arise to transmit variously modulated optical signals over a single optical fiber (even with different per channel bitrates). In this paper the authors show an optimal combined WDM system configuration that provides the least bit-error-rate values for the signals detected in system's channels. It is found that the minimal channel spacing for differently modulated optical signals in the investigated mixed data rates WDM system is 75 GHz if these signals are transmitted with 10 Gbit/s and 40 Gbit/s per channel bitrates. It is revealed that such a system's average spectral efficiency depends also on a combined system's configuration in the case of channel separation with equal frequency intervals.

WDM Network Issues: QOT Impairments, Dynamic Bandwidth Allocation, Modeling and Monitoring Schemes based on ML

A 4 X 622 Mb/s 40 km WDM optical communication system with EDFA is described. Four DFB-LD modules with 1.55 micrometers wavelength range are used in the transmitters. An EDFA with 1480 nm pump LD is used as a boost power amplifier. It suppresses noises efficiently. A Fabry-Perot interferometer is used as a demultiplexer. Through 40 km transmission, the output waveform of the receiver is obviously improved. It makes the research on long haul and WDM/FDM optical communication systems great progress.

Wavelength division multiplexing (WDM) systems are widely deployed in high-capacity long-haul transmission systems. They can provide cost-effective additional capacity on fibers overloaded by the increase in data traffic. Current WDM systems are used mainly for point-to-point transmission links. Next generation WDM technologies are expected to provide full functionality at both the system and network levels. Next generation WDM system will require many optical components, including optical filters, add/drop multiplexers, circuit switches and wavelength converters. Optical components using planar lightwave circuits (PLCs) are now widely used in WDM systems. Arrayed waveguide gratings (AWGs), in particular, play an important role in current WDM systems. In the next generation system, optical components using PLCs are expected to provide many functions that counterparts cannot. In this paper, we will describe the current and future WDM components using PLCs, focusing on AWGs and switchable add/drop filters.

We study the blocking probability and performance of single‐fiber and multifiber optical networks with wavelength division multiplexing (WDM). We extend the well‐known analytical blocking probability model by Barry and Humblet to the general model, which is proposed for both single‐fiber and multifiber network paths with any kind of wavelength conversion (no, limited, or full wavelength conversion) and for uniform and nonuniform link loads. We investigate the effect of the link load, wavelength conversion degree, and the number of wavelengths, fibers, and hops on blocking probability. We also extend the definition of the gain of wavelength conversion by Barry and Humblet to the gain of performance, which is fully general. Thanks to this definition and implementation of our model, we compare different WDM node architectures and present interesting results.

In this PhD dissertation multi-rate models are examined for the performance analysis of telecommunication networks through mathematical analysis and simulation. Particular emphasis is given to optical networks. The main goal is the development of analytical models for the calculation of network performance metrics, such as blocking probabilities, transmission delay and utilization of the common channel. The proposed analytical models are distinguished according to the network technologies. Three different technologies are considered: A) Wavelength routed optical networks. B) Optical access networks. C) Wireless Internet access networks. Multi-rate loss models are proposed for the performance evaluation of wavelength routed optical networks. Firstly, the case of a single link is considered and then a mesh all-optical network is examined. In addition, analytical models are proposed for Optical Packet Switching (OPS) networks, for the case of an all-optical OPS switch and of an OPS mesh network. Multi-rate analytical models are proposed for the evaluation of the performance of Passive Optical Networks (PONs) implementing different multiple access methods. For the case of Time Division Multiple Access (TDMA) the Ethernet PON is studied, which supports multiple service-classes. Regarding the Wavelength Division Multiplexing (WDM) PONs a hybrid WDM-TDMA PON is considered and the call-level performance is evaluated. Calls are distinguished by their arrival process, which can be random or quasi random, by their bandwidth requirements, which can be fixed of elastic and by their behavior during their service, which can be calls of fixed transmission rate or calls that alternate between ON and OFF periods. Finally multi-rate loss models are proposed for the case of Optical Code Division Multiple Access (OCDMA) PONs that take into account the user activity and the presence of additive noise in the transmission channel. For the performance analysis of wireless Internet access networks analytical models are proposed, which implement the IEEE 802.11 protocol or the IEEE 802.11e protocol. The proposed analysis calculated the saturation throughput and the end-to-end packet delay as a function of the Medium Access Control (MAC) delay and the queueing delay. In all cases the accuracy of the proposed models is validated through simulation.

In this paper, we compare performance of fixed-grid Wavelength Division Multiplexing (WDM) and Elastic Optical Networks (EONs) in dynamic provisioning of many-to-many (m2m) flows. Currently, with a growth of services relying on many-to-many communication paradigm such as distributed computing, inter-Data Center communication, content delivery networking or other requiring high-bandwidth in group communication, it is vital to deliver new solutions facilitating these demanding transmissions. Therefore, the authors investigate provisioning of m2m traffic in high-performance optical networks. This work focuses on dynamic Routing and Wavelength Assignment (RWA) problem in WDM networks as well as Routing and Spectrum Allocation (RSA) problem in EONs for m2m flows using replicated communication through auxiliary rendezvous servers.

This paper describes the performance improvement of 10-Gb/s four-channel WDM dispersion-supported transmission systems by using broadened passband arrayed-waveguide grating demultiplexers. Multimode interference couplers are assumed to be used to broaden the passaband of these demultiplexers. Performance Improvement of 40-Gb/s Capacity Four-Channel WDM Dispersion-Supported Transmission by Using Broadened Passband Arrayed-waveguide Grating Demultiplexers Mario M. Freire Department of Mathematics and Computer Science, University of Beira Interior Rua Marques d'Avila e Bolama, P-6200 Covilha, Portugal Telephone: +351 75 3101700, Fax: +351 75 26198, E-mail: mfreire@ alpha.ubi.pt Henrique J. A. da Silva Department of Electrical Engineering, Pole II of University of Coimbra Pinhal de Marrocos, P-3030 Coimbra, Portugal Telephone: +351 39 7006248, Fax: +351 39 7006247, E-mail: hjas@ci.uc.pt Summary Integrated N×N wavelength multiplexers based on arrayed-waveguide gratings (AWG) are being developed for wavelength division multiplexing (WDM) systems and networks, since they can offer four basic functions: multiplexing, demultiplexing, add/drop multiplexing, and N×N full-interconnection [1]. The use of this technology for demultiplexing in high density WDM systems may impose very stringent requirements on the alignment of signal wavelengths and demultiplexers due to their peaked (Gaussian-like) spectral passband. However, the passband of these demultiplexers may be broadened by the use of multimode interference couplers (MMI), as proposed and demonstrated in [2]. In this paper, we describe the performance improvement due to the use of broadened passband AWG demultiplexers in 40-Gb/s capacity four-channel WDM dispersion-supported transmission (DST) systems with 0.5 nm channel spacing. The block diagram of the simulated 10-Gb/s four-channel WDM-DST system is shown in Fig. 1. The system model is broadly similar to the one reported in [3] and includes a rate equation model for quantum-well lasers, and the frequency responses of a PIN photodiode and of a standard singlemode fiber (SMF) with chromatic dispersion of 17 ps/(nm.km) at 1532 nm. The frequency response of the AWG filter is assumed to be Gaussian and the frequency response of the broadened passband AWG filter is modeled by the double Gaussian approximation [2] with r = 2 , which is the ratio between the peak separation and the FWHM of each simple Gaussian profile. The optical amplifiers (EDFAs) have been considered as linear with a noise figure of 6 dB and an equivalent noise bandwidth of 1 THz. A RC lowpass filter was used to provide the 3-dB bandwidth required by the DST method [4]. The receiver sensitivity was estimated taking into account the signal-ASE and ASE-ASE beat noises, the thermal and shot noises, as well as the contribution due to frequency-to-intensity conversion of laser phase noise after propagation via dispersive fibers [5]. Fig. 2 shows the receiver sensitivity for channel 2 versus fiber length for single-channel DST, without optical filters, and for four-channel WDM-DST using an arrayed-waveguide grating demultiplexer with (BP-AWG) and without (AWG) broadened passband. For comparison purposes, the receiver sensitivity of four-channel WDM-DST using a three-mirror Fabry-Perot demultiplexer (TMF) is also shown. For distances larger than 80 km, the performance of four-channel WDM-DST systems using three-mirror Fabry-Perot demultiplexers is close to the performance of single-channel DST systems without optical filters. Compared with the performance of single-channel DST without optical filters, the use of conventional arrayed-waveguide grating filters as demultiplexers in four-channel WDMDST degrades the system performance at least 0.6 dB for link lengths larger than 11 km. However, the use of broadened passband AWG demultiplexers instead of the conventional AWG demultiplexers improves the performance of the four-channel WDM-DST system at least 1.5 dB, for link lengths larger than 11 km (see Fig. 2). Detailed BER characteristics for channel 2 are displayed in Fig. 3 for four-channel WDM-DST via 204 and 253 km SMF. For the 204 km transmission simulation, sensitivities of -23.886, -23.169 and -24.827 dBm have been estimated for TMF, AWG and BP-AWG demultiplexers, respectively. The BER curves for 253 km clearly indicate an error floor due to laser phase noise. In conclusion, the use of broadened passband AWG demultiplexers improves the performance of four-channel WDM-DST systems with 0.5 nm channel spacing, while conventional AWG demultiplexers are less suitable to operate at this channel spacing.

Along with the emergence and maturity of 100Gbit/s technologies, numbers of trial and commercial 100Gbit/s Wavelength Division Multiplexing (WDM) systems have been established worldwide. The research-oriented lab tests of 100Gbit/s WDM systems were done by China Unicom in 2012. The 100Gbit/s technologies of polarization multiplex-quadrature phase shift keying with coherent detection from multiple vendors have been studied. There are some further issues to be specified before the commercial application of 100Gbit/s WDM system is implemented in large scale in backbone network, including optical performance parameters, optical performance monitoring of 100Gbit/s system, protection mechanism, selection of client interface and comprehensive Operation, Administration and Maintenance (OAM).

In this paper we provide analytical insights for dimensioning a multi-layer network and in particular the virtual optical transport network topology exported to the packet client layer according to cost and power consumption. A new approach is described, approximating optimum routing, that can be effectively used to provide an estimation of network cost and reference architectures in network implementations. Results using this estimation approach are compared with those obtained using other estimation approaches regarding bandwidth allocation and network costs. We found that the approximated routing calculations, applied on a virtual network topology, do not significantly penalize the accuracy of the results. This approach can be extended to analyze the impact of new a optical networking technique, flexible-grid wavelength division multiplexing (WDM), providing some insights regarding scenarios in which migration from fixed-grid WDM systems to flexible-grid WDM systems would be advantageous in terms of capital cost and power consumption.

There is a rapidly increasing data flow between sensors and on-board processors in avionic platforms. Electro-optic (EO) sensors are moving to hyperspectral and radar to phased array to enable precision targeting, wide field of view surveillance and navigation. These trends call for next generation optical network technology which has to provide increasing high speed data transmission under harsh conditions. Recent developments go beyond simple point-to-point fiber links towards establishing optical distribution networks to deal with the data traffic [1]. A flexible and potentially low-cost implementation is the passive optical network (PON) which scales easily to increasing needs simply by upgrading the peripheral units without need to change the fiber connections and infrastructure. PONs are well established in the commercial access market with the increasing push to fiber-to-the-home (FTTH) technologies which has led to the development of a variety of low-cost devices for these networks. A key enabler in our development of an avionics PON is the reflective semiconductor optical amplifier (RSOA) which combines amplification and modulation into a single device [2]. The RSOA is a non-resonant device, thus wideband with the potential for ruggedness, especially high temperature operation with small or no need for cooling. At higher data rates up to 20 Gbps a related device, the reflective electro-absorption modulator with integrated amplification (R-SOA-EAM) can be used instead. To complete the adaptation we replaced the laser, commonly used to provide optical input power in a PON architecture with another non-resonant device, the superluminescent LED (SLED). To create upgrade flexibility we utilized wavelength division multiplexing (WDM) which allows addition and subtraction of channels without changing hardware. Coarse WDM (CWDM) was chosen over Dense WDM (DWDM) for two reasons: the large channel width (20nm) of CWDM reduces cost by relaxing fabrication tolerance and renders the use of temperature control unnecessary, thereby increasing reliability. The concept and current state of development of our optical network is described in this paper.

Elastic optical network (EON) is a promising candidate for the next generation optical transport network because of its high spectrum efficiency and flexible spectrum allocation. However, to migrate from today’s dense wavelength division multiplexing (DWDM) network to EON, optical nodes such as reconfigurable optical add/drop multiplexers (ROADMs) should be replaced with the ones with expensive flexi-grid wavelength selective switches (WSSs). Thus, whether and how today’s optical network will be evolved to EON is still under debate. Meanwhile, with the technical maturity of optical super-channels that transmit bit rates at the level of 1 Tb/s, super-channels are expected to dominate the future optical transport network because of their attractiveness of high spectrum efficiency and superior cost effectiveness. In this paper, we propose a new quasi-coarse wavelength division multiplexing (Quasi-CWDM) optical network architecture that is compatible to today’s WDM network in spectrum operation, while still maintaining the flexibility of adaptation between the bit rate and the transparent reach of an optical super-channel, but not requiring expensive flexi-grid WSSs. Specifically, the Quasi-CWDM optical network employs large fixed frequency grids, whose spacing falls between the traditional CWDM and DWDM, e.g., 200 GHz or 400 GHz. To maintain the flexibility between the bit rate and the transparent reach of an optical super-channel, different modulation formats are chosen according to channel physical distances. To minimize network hardware cost and maximize carried user traffic demand, we develop a mixed integer linear programming (MILP) model and a heuristic algorithm that can efficiently groom upper-layer IP traffic onto the optical layer by optical super-channels. We compare the design based on the Quasi-CWDM network to those based on the DWDM network and the advanced EON. It is found that the proposed Quasi-CWDM network has a much lower hardware cost than the other two types of networks, while achieving spectrum efficiency close to EON.

With rapidly increasing demand for communication channels, wavelength division multiplexing (WDM) system are being deployed to expand the capacity. WDM systems require devices for the manipulation of multi-wavelength channels. Among these devices, the integrated acousto-optic tunable filter (AOTF) is rapidly gaining importance in the field of WDM communication systems because it has the combined features of rapid switching time, broad tuning range and parallel processing capability. The technology of hybrid unidirectional and focused transducer was adopted for the design of the AOTF. The AOTF consisted of a single-mode optical waveguide placed along the SAW propagation direction. Extensive researches areas, which were in optical add-drop multiplexers (OADM), gain equalization and optical switches, have been done.

This paper presents a simulation methodology for performance assessment of wavelength division multiplexing (WDM) systems using directly modulated quantum-well lasers and optically preamplified direct detection receivers. The methodology is based on a pure semi-analytical method which combines noiseless WDM transmission simulation with noise analysis in those systems. Using this approach, we discuss the performance implications of single-cavity, double-cavity and three-mirror Fabry-Perot (FP) demultiplexers for dispersion supported transmission (DST) of three WDM channels separated by 1 nm. Assuming that a three-mirror filter is used as demultiplexer, the performance of a 40 Gbit/s capacity four-channel WDM-DST system is assessed for 0.5 nm channel spacing. The robustness of the multichannel DST method against pattern dependencies is also investigated for this channel spacing.