Positioning of Intelligent Reflecting Surface with Sum and Difference Beams

In this paper, we investigate the fundamental multiple access (MA) scheme in an active intelligent reflecting surface (IRS) aided energy-constrained Internet-of-Things (IoT) system, where an active IRS is deployed to assist the uplink transmission from multiple IoT devices to an access point (AP). Our goal is to maximize the sum throughput by optimizing the IRS beamforming vectors across time and resource allocation. To this end, we first study two typical active IRS aided MA schemes, namely time division multiple access (TDMA) and non-orthogonal multiple access (NOMA), by analytically comparing their achievable sum throughput and proposing corresponding algorithms. Interestingly, we prove that given only one available IRS beamforming vector, the NOMA-based scheme generally achieves a larger throughput than the TDMA-based scheme, whereas the latter can potentially outperform the former if multiple IRS beamforming vectors are available to harness the favorable time selectivity of the IRS. To strike a flexible balance between the system performance and the associated signaling overhead incurred by more IRS beamforming vectors, we then propose a general hybrid TDMA-NOMA scheme with device grouping, where the devices in the same group transmit simultaneously via NOMA while devices in different groups occupy orthogonal time slots. By controlling the number of groups, the hybrid TDMA-NOMA scheme is applicable for any given number of IRS beamforming vectors available. Despite of the non-convexity of the considered optimization problem, we propose an efficient algorithm based on alternating optimization, where each subproblem is solved optimally. Simulation results illustrate the practical superiorities of the active IRS over the passive IRS in terms of the coverage extension and supporting multiple energy-limited devices, and demonstrate the effectiveness of our proposed hybrid MA scheme for flexibly balancing the performance-cost tradeoff.

Intelligent Reflecting Surfaces (IRS), a planar array consisting of a large number of low-cost and low-complexity metal patch elements, is predicted to be among the key technologies in future wireless communications. This is mainly due to its capability to improve wireless energy and spectrum efficiency by reconfiguring the wireless environment in a smart and flexible way. IRS is capable of shifting the phase, amplitude, frequency, or even polarity of the impinging electromagnetic (EM) wave. However, only the phase-shift type of IRS is widely adopted in most scenarios. In this paper, we exploit the property of such IRS to directly modulate an incident EM wave with phase shift keying (PSK) modulation. We consider one transmit antenna that transmits a continuous single-tone electromagnetic (EM) wave, which is then modulated by the IRS and reflected toward the receiver. In addition to the theoretical explanation, we present simulation results with different modulation orders. Moreover, we validated the simulation results by experiment. Furthermore, we also proposed a beam scanning method to obtain IRS patterns to steer the beam towards the desired direction in an adaptive manner. One optimal pattern that maximizes the received power is then selected from the beam scanning codebook. By doing so, a wireless path strength can be significantly improved.

Intelligent Reflecting Surfaces (IRS) is a groundbreaking innovative technique to boost energy and spectral efficiency in upcoming wireless systems, enabling simultaneous wireless information and power transfer (SWIPT). This paper optimizes Energy Harvesting Efficiency (EHE) in a multi-input multi-output (MIMO) SWIPT system, where an access point (AP)/base station (BS) uses an IRS to serve multi energy receivers (ERs) and information receivers (IRs). We formulate an EHE optimization problem, designing active and passive beamforming while satisfying the AP/BS power constraints, IRS unit-modulus constraints and IR rate demands in a linear EH model. The Linear Matrix Inequalities (LMIs) are approximated for efficient solutions. And second-order cone programming (SOCP) is solved via convex optimization (CVX), while the penalty convex-concave procedure (CCP) guarantees convexity to non-convex problems. Next, an alternating optimization (AO)-reliant iterative algorithm derived sub-optimal solutions with slack variables. According to simulation results, for all ERs within a linear EH design/model, the proposed algorithm improves total EHE by 40% to 45% compared to randomize, No-IRS, and decode-and-forward (DF) relay strategies. Ultimately, highlighting IRS’s benefit in improving quality of service (QoS) by tweaking its elements and AP/BS antennas.

In this paper, we consider deploying an intelligent reflecting surface (IRS) to enhance the downlink (DL) energy transfer and uplink (UL) information transmission efficiency for secure multiple-input multiple-output (MIMO) wireless powered communication networks (WPCNs). We aim to maximize the secrecy throughput of all users by jointly optimizing the DL/UL time allocation, the energy transmit covariance matrix of hybrid access point (AP), the information transmit beamforming matrix of users and the phase shifts of IRS in DL/UL, subject to constraints of energy/information transmit power at the hybrid AP/users and that of unit-modulus IRS phase shifts for DL/UL. To tackle the non-convex problem, we first transform the original problem into an equivalent form based on the mean-square error (MSE) method given time allocation, and then apply the alternating algorithm to update the optimization variables iteratively. Specifically, the energy covariance matrix and the information beamforming matrix are obtained based on the dual subgradient method. For the IRS phase shifts, we investigate two IRS beamforming reflection setups, namely different DL/UL IRS beamforming and identical DL/UL IRS beamforming. For the former case, the second-order cone programming technique and the Majorization-Minimization algorithm/element by element iterative algorithm are applied to obtain the DL and UL IRS phase shifts, respectively. For the latter case, the IRS phase shifts are obtained by the successive convex approximation technique. To further reduce the computational complexity of the single-user system, we derive the closed-form solutions of IRS phase shifts in each iteration for the two different reflection setups. Simulation results show that all the proposed algorithms can greatly improve the secrecy throughput compared to the conventional system without IRS.

This article investigates physical-layer security (PLS) of a typical wireless-powered communication (WPC) system with the aid of intelligent reflecting surface (IRS) in the presence of a passive eavesdropper for Internet of Things (IoT), and proposes three IRS-aided secure WPC modes. Specifically, in mode-I, the IRS is deployed between hybrid access point (HAP) and wireless user (U) for co-located power station (PS) and access point (AP). In mode-II, the IRS is deployed between AP and U for separate PS and AP, while in mode-III, the IRS is deployed between PS and U for separate PS and AP. For each mode, the optimal phase shift is designed to maximize the reception of energy and information at the legitimate receiver. We comprehensively analyze the performance of each mode, and derive the closed-form expressions of connection outage probability (COP), secrecy outage probability (SOP), and effective secrecy throughput (EST) for each mode, respectively. The theoretical analysis and simulation results reveal that from the perspective of reliability, mode-I can achieve the best COP with the increased number of IRS elements, while mode-II and mode-III have a similar COP. From the perspective of security, mode-II can achieve the best SOP with the increased number of IRS elements, while mode-I and mode-III have a similar SOP. Moreover, under the condition of small transmission power at HAP/PS or small number of IRS elements, mode-I has the best EST, while as the power or the number increases, the EST of mode-II becomes the best one.

This paper presents a comparative analysis of intelligent reflecting surface (IRS) technology versus conventional amplify-and-forward (AF) and decode-and-forward (DF) relay schemes in wireless communication. By focusing on transmit power, energy efficiency, and the minimum IRS elements required to outperform traditional relaying, we explore IRS’s potential as an energy efficient alternative. Our analysis shows that IRS configurations, especially with optimal phase shifts, achieve substantial power savings and superior energy efficiency over to AF and DF relays. Moreover, IRS requires fewer elements to meet or exceed relaying performance under higher data rate demands, making it an ideal choice for energy conscious, high performance network designs. These results highlight IRS technology as a promising solution for sustainable, next-generation communication networks.

A Survey of Intelligent Reflecting Surfaces: Performance Analysis, Extensions, Potential Challenges, and Open Research Issues

Combining intelligent reflecting surface (IRS) and unmanned aerial vehicle (UAV) offers a new degree of freedom to improve the coverage performance. However, it is more challenging to secure the air-ground transmission, due to the line-of-sight (LoS) links established by UAV. Since IRS is a promising solution for wireless environment reconfiguration, in this paper, we propose an aerial IRS-assisted secure transmission design in wireless networks. In particular, an access point (AP) equipped with a uniform planar array serves several single-antenna legitimate users in the presence of multiple single-antenna eavesdroppers, whose precise positions are unknown. An IRS is mounted on the UAV to help establish desired virtual LoS links between the AP and legitimate users, while ensuring their security. We aim to maximize the worst-case sum secrecy rate by jointly optimizing the hovering position of UAV, the transmit beamforming of AP and the phase shifts of IRS, subject to the requirement of minimum rate for legitimate users. To tackle this non-convex problem, we first decompose it into three subproblems, which are transformed into convex ones via successive convex approximation. An alternating algorithm is then proposed to solve them iteratively. Simulation results show the effectiveness of the proposed scheme and the security improvement by the joint optimization.

Intelligent reflecting surface (IRS) has emerged as a cost-efficient technique to improve the wireless network’s capacity and performance. Existing works on IRS have mainly considered IRS being deployed in the environment to dynamically control the wireless channels between the base station (BS) and its served users in favor of their communications. In contrast, we propose in this paper a new integrated IRS-BS architecture by deploying IRSs inside the BS’s antenna radome to directly reconfigure the signal radiation to/from the BS’s antennas. In other words, the IRSs can be considered as auxiliary passive arrays with real-time reconfigurability equipped at the BS to enhance its communication performance cost-effectively. Since the distance between the integrated IRSs and BS’s antenna array is practically small (in the order of several to tens of wavelengths), the path loss among them is significantly reduced as compared to conventional IRS deployed much farther away from the BS, while the real-time control of the IRS’s reflection by the BS becomes easier to implement. However, the resultant near-field channel model also becomes drastically different from its far-field counterpart for conventional far-away IRSs in the literature. Thus, we propose an element-wise channel model for IRS to characterize the channel vector between each single-antenna user and the antenna array of the BS, which includes the direct (without any IRS’s reflection) as well as the single and double IRS-reflection channel components. Based on this channel model, we formulate a problem to optimize the reflection coefficients of all IRS reflecting elements for maximizing the uplink sum-rate of the users. By considering two typical cases with/without perfect channel state information (CSI) at the BS, the formulated problem is solved efficiently by adopting the successive refinement method and iterative random phase algorithm (IRPA), respectively. Numerical results validate the substantial capacity gain of the integrated IRS-BS architecture over the conventional multi-antenna BS without integrated IRS. Moreover, the proposed algorithms significantly outperform other benchmark schemes in terms of sum-rate, and the IRPA without CSI can approach the performance upper bound with perfect CSI as the training overhead increases.

Intelligent reflecting surface (IRS) is a promising new paradigm to achieve high spectral and energy efficiency for future wireless networks by reconfiguring the wireless signal propagation via passive reflection. To reap the potential gains of IRS, channel state information (CSI) is essential, whereas channel estimation errors are inevitable in practice due to limited channel training resources. In this paper, in order to optimize the performance of IRS-aided multiuser systems with imperfect CSI, we propose to jointly design the active transmit precoding at the access point (AP) and passive reflection coefficients of IRS, each consisting of not only the conventional phase shift and also the newly exploited amplitude variation. First, the achievable rate of each user is derived assuming a practical IRS channel estimation method, which shows that the interference due to CSI errors is intricately related to the AP transmit precoders, the channel training power and the IRS reflection coefficients during both channel training and data transmission. Then, for the single-user case, by combining the benefits of the penalty method, Dinkelbach method and block successive upper-bound minimization (BSUM) method, a new penalized Dinkelbach-BSUM algorithm is proposed to optimize the IRS reflection coefficients for maximizing the achievable data transmission rate subjected to CSI errors; while for the multiuser case, a new penalty dual decomposition (PDD)-based algorithm is proposed to maximize the users' weighted sum-rate. Simulation results are presented to validate the effectiveness of our proposed algorithms as compared to benchmark schemes. In particular, useful insights are drawn to characterize the effect of IRS reflection amplitude control (with/without the conventional phase shift) on the system performance under imperfect CSI.

This study investigates the integration of an intelligent reflecting surface (IRS) into an unmanned aerial vehicle (UAV) platform to utilize the advantages of these leading technologies for sixth-generation communications, e.g., improved spectral and energy efficiency, extended network coverage, and flexible deployment. In particular, we investigate a downlink IRS–UAV system, wherein single-antenna ground users (UEs) are served by a multi-antenna base station (BS). To assist the communication between UEs and the BS, an IRS mounted on a UAV is deployed, in which the direct links are obstructed owing to the complex urban channel characteristics. The beamforming at the BS, phase shift at the IRS, and the 3D placement of the UAV are jointly optimized to maximize the sum rate. Because the optimization variables, particularly the beamforming and IRS phase shift, are highly coupled with each other, the optimization problem is naturally non-convex. To effectively solve the formulated problem, we propose an iterative algorithm that employs block coordinate descent and inner approximation methods. Numerical results demonstrate the effectiveness of our proposed approach for a UAV-mounted IRS system on the sum rate performance over the state-of-the-art technology using the terrestrial counterpart.

In this paper, we consider an intelligent reflecting surface (IRS) enabled mobile network, where a fixed access point (AP) communicates with a mobile user (MU) via the aid of an IRS. We assume that the MU moves from one elementary square to another following a Markov random walk within a grid, and propose a maximum a posteriori (MAP) criterion to track the movement of the MU by leveraging the line-of-sight component of the IRS-MU link. Since it is infeasible to derive an explicit expression for the average probability of estimation error (APEE) for the proposed MAP criterion, we derive a closed-form upper bound for the APEE, which is used as the cost function to optimize the phase shifts of the IRS units. Considering the unit modulus constraints incurred by the IRS units, a manifold optimization (MO) method is firstly employed to gain a favorable solution to the formulated optimization problem, followed by a low-complexity codebook based solution to circumvent the high computational cost of the MO method. Our numerical results demonstrate the superior performance of the proposed IRS phase shift designs over the benchmark method.

An optimized scheme for energy efficient wireless communication via intelligent reflecting surfaces

This work considers covert communications with the aid of an intelligent reflecting surface (IRS). We jointly design the transmit power and IRS's reflection phase shifts and amplitudes to enhance covert communication performance. To this end, we first derive the total detection error rate at a warden. We then determine the IRS's optimal phase shifts and develop an effective one-dimensional search method to identify the IRS's optimal amplitudes. We show that the IRS can significantly improve the achievable covertness. In addition, optimizing the IRS's amplitudes on top of its phase shifts significantly outperforms fixing them as unit in covert communications.

Wireless communication environment becomes more and more complex especially when facing vicious eavesdroppers and external jammers. Intelligent reflecting surface (IRS) can provide secure or anti-jamming communication approaches via passively reflecting with low power consumption and high cost efficiency. Unmanned aerial vehicle (UAV) also can be used to cooperatively transmit useful signals of legitimate users with vicious attackers. Carrying IRS on UAV can add new cooperative strategies, such as trajectory or height of UAV, numbers of reflecting elements or phase shift of IRS, to improve secure and anti-jamming performance of legitimate users. Two cooperative transmission schemes assisted with UAV and IRS are proposed to confront passive eavesdroppers or smart jammers in this paper. The first kind of cooperation is to select UAV relay or IRS reflecting strategy to improve energy efficiency of system with passive eavesdroppers. The second kind of cooperation is to jointly optimize phase shifts of IRS and trajectory of UAV to enhance transmission capacity with smart jammers. Simulation results show that, with the help of the cooperation of UAV and IRS, secure and reliable communications can be realized and system performance can be improved compared with no cooperation scheme or only one kind of cooperation with UAV or IRS scheme.