Power handling for LCoS spatial light modulators

In 3‐D display system based on opto‐electronic reconstruction of digitally recorded hologram, the field of view of such a system is limited by the spatial resolution of the liquid crystal on silicon (LCOS) spatial light modulator (SLM) used to perform the opto‐electronic reconstruction. In this article, the spatial resolution limitation of LCOS SLM associated with fringe field effect and interpixel coupling is determined by liquid crystal director simulation and Finite Difference Time Domain (FDTD) simulation. The diffraction efficiency loss associates with the imperfection in phase profile is studied with an example of opto‐electronic reconstruction of an amplitude object. A high spatial resolution LCoS SLM with wide reconstruction angle is proposed.

Surface-stabilized antiferroelectric liquid crystals (AFLCs) and V-shape smectics share the spontaneous generation of intermediate transmission states, i.e. analogue grayscale. On the other hand, liquid crystal on silicon (LCOS) appears to be a promising alternative to thin-film transistors (TFTs) in the preparation of reflective microdisplays and spatial light modulators (SLMs). The feasibility of preparing LCOS SLMs using AFLC and V-shaped LCs has been analyzed. A comparative study of a number of AFLC and V-shape materials as candidates for LCOS SLMs has been carried out. Test cells below 1 µm have been prepared using an ITO-coated transparent glass plate and an aluminized silicon back plate mimicking the actual LCOS device. AFLC waveforms compatible to low-voltage operation of the silicon backplane have been demonstrated. V-shape waveforms have been designed and demonstrated as well. The results show that both LC families may be employed in this specific application. Dynamic behavior, with frame rates over 200 Hz, is especially remarkable.

We present an aided optical alignment method using the liquid crystal on silicon spatial light modulator (LCoS-SLM). An optical system composed of an interferometer and an LCoS-SLM was established to verify the effectiveness of the method. The system was also calibrated to solve the phase modulation nonlinear and nonuniformity problem for better performance of LCoS-SLM as an easily programmable phase compensator. The LCoS-SLM could modulate the phase of incident light precisely to generate an accurate phase desired to achieve a virtual off-axis parabolic phase to generate light spots array. Finally, the 2 × 2 light spots array generated by the optical system was used to verify its potential in optical alignment.

Liquid-crystal on silicon spatial light modulators (LCOS-SLM) with pixel size as small as few microns enable the implementation of programmable diffraction gratings with large deflection angles (small period). We study triplicator phase gratings at the limit of the LCOS spatial resolution, where the binary phase profile is the only alternative. First, we show the effect of the sinc envelope that unavoidably arises from the LCOS pixelation. Then, we use the Fourier transform theory to analyze the binary phase grating in a pixelated device in terms of the pixel size, fill factor and phase difference between the two levels in the grating. The experimental diffraction pattern of a binary triplicator grating displayed on the SLM with a period of 2 pixels reveals that pixel crosstalk becomes relevant. Its effect on the conditions to render a triplicator and on the diffraction efficiency is analyzed.

Liquid crystal on silicon (LCoS) spatial light modulators (SLMs) are versatile scientific tools relevant to an increasingly wide variety of research and technological applications including digital holography, wavefront correction, optical tweezing, and non-mechanical beam steering to name a few. Since SLMs are used in a multitude of different ways, some aspects of device performance (e.g., response time) are crucial to certain applications while being irrelevant to others. In this work we couple our standard SLMs with a thermo-electric cooler, allowing for tunability of the device operating temperature from 0° to 75 °C. We show that there is an inherent tradeoff between the liquid crystal response time and the phase stability of an SLM, and that the operating temperature offers a means of controlling this tradeoff. Furthermore, this paper aims to provide the reader with a brief but thorough explanation of SLM operating principles and device structure, defines the performance metrics of the SLM, and provides a methodology for measuring the specifications. By allowing control over the SLM operating temperature and detailing how temperature affects device functionality, SLM users are afforded greater experimental flexibility and will be better able to tailor the performance of their device for the given project or application at hand.

This work presents the application studies of holographic techniques using LCoS-SLM (Liquid Crystal on Silicon - Spatial Light Modulators) to replace the masks in photolithography process. Computer-generated holograms obtained from two images with known dimensions, simulating a Clear Field Mask and a Dark Field Mask, were applied to one LCoS-SLM connected to an holographic optical setup capable of reducing the reconstructed images, allowing the survey of the most relevant parameters of the photolithography process for the manufacture of fine structures and from their characterization identify the limits imposed by LCoS-SLM in the process. The results are good and presents excellent possibilities of a holographic system applied to processes of Maskless Photolithography.

A high quality and high performance 2D Spatial Light Phase Modulator has been developed for wide range of basic and practical applications. We will discuss how LCOS micro‐display device is developed into LCOS‐SLM for various important non‐display applications ranging from basic and applied researches such as singular optics and fluorescence microscopy to industrial applications in laser processing and machining.

We have developed a high-resolution, multi-color retinal imaging system using liquid crystal adaptive optics. A liquid crystal on silicon (LCOS) spatial light modulator (SLM) is used to correct ocular aberrations. In order to compensate for the dependency of an LCOS SLM on optical wavelength and acquire aberration-corrected images at different color, we apply an open-loop technique. In the open-loop technique, the imaging light is separated from the sensing light and the optimal phase modulation is applied only to the imaging light while the sensing light is not phase-modulated. With the system, in vivo imaging of the human retina is achieved by using illumination light at wavelength of 655nm and 593nm and sensing light at 780nm. Photoreceptors are clearly revealed at each illumination wavelength with the liquid crystal adaptive optics.

A novel imaging technique that produces accurate amplitude and phase images of an optical fiber facet using only a phase-only liquid-crystal on silicon (LCOS) spatial light modulator (SLM) and a single-pixel detector is presented. The system can take images in two orthogonal polarizations and so provides a powerful tool for modal characterization of multimode fibers, which is of increasing importance due to their burgeoning use in telecommunications and medical applications. This technique first uses a simulated annealing algorithm to compute a hologram that collects light from a small region of the fiber facet. Next, the fiber facet is automatically brought into focus using adaptive aberration correction on the SLM. Finally, a common-path interferometer is created using the SLM, and the phase of the optical field at each pixel is determined. Finally, high-definition amplitude and phase images of a ring-core refractive index fiber are presented as a proof-of-principle demonstration of the technique.

In this paper we present a method for topography measurement of high gradient reflective microstructures that overcomes the limited numerical aperture (NA) of a digital holographic (DH) system working in reflection. We consider a case when a DH system is unable to register the light reflected from the full sample area due to insufficient NA. To overcome this problem, we propose digital holography in a microscope configuration with an afocal imaging system and a modified object arm in the measurement setup. The proposed modification includes application of a spatial light modulator (SLM) based on liquid crystal on silicon (LCoS) technology for multidirectional plane wave illumination. The variable off-axis illumination enables characterization of the sample regions that cannot be imaged by the limited NA of a classical DH system utilizing on-axis illumination. In the proposed method, the final object topography is merged from a set of captured object waves corresponding to various illumination directions using a novel automatic algorithm. The proposed technique is experimentally validated by full-field measurement of a silicon mold with a high gradient of shape.

We present a method for reducing the phase flicker originated by the pulsed modulation of a Liquid Crystal on Silicon (LCoS) Spatial Light Modulator (SLM). It consists in reducing the temperature of the LCoS in a controlled way, in order to increase the viscosity of the liquid crystal. By doing this, we increase the time response of the liquid crystal, and thus reduce the amplitude of phase fluctuations. We evaluate the efficacy of this method quantifying the temporal evolution of phase shift using an experiment that is insensitive to optical polarization fluctuations. Additionally, we determine the effect of the temperature reduction on the effective phase modulation capability of the LCoS. We demonstrate that a reduction of up to 80% of the flicker initial value can be achieved when the LCoS is brought to -8 °C.

This work describes the steps necessary for a holographic pattern projection of high quality with a phase-only Liquid crystal on silicon spatial light modulator (LCoS-SLM). The aim is high-throughput optical lithography on nonplanar surfaces. Aspects of diffractive optical element calculation as well as aspects of aberration compensation are needed to increase the uniformity and fidelity of intricate patterns.

The cavity supports the orthogonal reference beam families as its eigenmodes while enhancing the reference beam power. Such orthogonal eigenmodes are used as additional degree of freedom to multiplex data pages, consequently increase storage densities for volume Holographic Data Storage Systems (HDSS) when the maximum number of multiplexed data page is limited by geometrical factor. Image bearing holograms are multiplexed by orthogonal phase code multiplexing via Hermite-Gaussian eigenmodes in a Fe:LiNbO3 medium with a 532 nm laser at multiple Bragg angles by using Liquid Crystal on Silicon (LCOS) spatial light modulators (SLMs) in reference arms. Total of nine holograms are recorded with three angular and three eigenmode.

An autostereoscopic display system was designed and constructed. The design, which uses pupil imaging with a curved mirror, is described. It employs a monocentric configuration to enable a wide field of view and large pupils while keeping the lens diameters small to fit them within the interoccular separation. For each eye, image formation was accomplished using 1920 x 1200 liquid crystal on silicon (LCOS) spatial light modulators in a 3-panel configuration. The design employs custom curved diffusers, which were developed to optimize throughput, contrast, and pupil illumination uniformity.

2-D optical phased array (OPA) antenna based on a liquid crystal on silicon (LCOS) spatial light modulator is introduced. Diffraction efficiency of the 1-D OPA for fine angle beam steering and 2-D OPA for aberration correction is characterized experimentally and by computer simulation. Excellent agreement between the simulation, measurement and empirical model is observed. Large aperture transmitter for long distance free space communication is analyzed by wave optics simulation. The system performance for beam steering and correction for wavefront aberration in large aperture transmitter is discussed.