PySio: A New Python Toolbox for Physiological Signal Visualization and Feature Analysis.

Heart period variability has been considered for clinical assessment of autonomic function, determining the presence of haemorrhage or disease states, and for predicting mortality from traumatic injury. However, for heart period variability to be clinically useful, a number of important methodological issues should be addressed, including the minimum number of R-R intervals (RRI) required for accurate derivation, and the reproducibility of these metrics. ECGs were recorded for > or =10 min in 18 resting, supine subjects (12 M/6 F; 19-55 years). Heart period variability analyses included 21 time, frequency and complexity domain metrics. For assessment of minimum RRIs required, measurements were made from ECG recordings of 5 min down to 30 s for time and frequency domain metrics, and from 800 RRIs down to 100 RRIs for complexity metrics, by methodical truncation of the data set. Inter-subject variability was assessed by calculating the range and co-efficient of variation (%CV) across all subjects. Two independent 30 s or 100 RRI ECG segments were used to assess intra-subject variability via calculation of %CV in each subject. Six time and frequency domain metrics were robust down to 30 s of data, while five complexity metrics were robust down to 100 RRIs. All time and frequency domain metrics (except for RRI) exhibited high inter-subject variability (CVs > or = 30.0%), while five of eleven complexity metrics displayed low inter-subject variability (CVs < or = 8.5%). In the assessment of intra-subject variability in metrics valid with 30 s or 100 RRIs of ECG, only one time domain and four complexity metrics had CVs < 10%. Metrics that are highly reproducible and require few RRIs are advantageous for patient monitoring as less time is required to assess physiological status and initiate early interventions. Based on our analyses from healthy, resting humans, we have identified a select cohort of heart period variability metrics that performed well in regards to these two criteria.

Third order time and frequency analysis has exhibited great potential for correlation analysis of multi-sensor datasets, but is usually presented as separate time domain and frequency domain approaches. A combined framework of both frequency domain and time domain has rarely been used. This paper proposes a non-parametric third order time and frequency domain framework which used two dimensional Fourier transforms to bridge the gap between time domain and frequency domain. A unified framework offers flexibility and efficiency to apply to data. In this paper we study neural spike train data treated as stochastic point processes. In time domain direct analysis, third order cumulant densities of spike trains are applied, which need all first-, secondand third order product densities to be calculated before constructing the third order cumulant density, which brings additional challenges. The novelty in this study is that a new framework is proposed which can offer an alternative approach without calculating lower order quantities and can reveal nonlinear relationship between neural recordings. The results show that the present framework provides a novel non-parametric method to estimate both time and frequency domain measurements which is applicable to neural spike trains.

Physics-informed neural networks (PINNs) represent a transformative approach to data models by incorporating known physical laws into neural network training, thereby improving model generalizability, reduce data dependency, and enhance interpretability. Like many other fields in engineering and science, the analysis of physiological signals has been influenced by PINNs in recent years. This manuscript provides a comprehensive overview of PINNs from various perspectives in the physiological signal analysis domain. After exploring the literature and screening the search results, more than 40 key studies in the related domain are selected and categorized based on both practically and theoretically significant perspectives, including input data types, applications, physics-informed models, and neural network architectures. While the advantages of PINNs in tackling forward and inverse problems in physiological signal contexts are highlighted, challenges such as noisy inputs, computational complexity, loss function types, and overall model configuration are discussed, providing insights into future research directions and improvements. This work can serve as a guiding resource for researchers exploring PINNs in biomedical and physiological signal processing, paving the way for more precise, data-efficient, and clinically relevant solutions.

We describe the main properties of the EQUATOR airborne geophysical system and how the system can be employed to solve some engineering and environmental problems. To date, the EQUATOR system has been used for groundwater search in 2014 and 2015 in Siberia. The name “EQUATOR” originates from the intention to EQUATE, or to balance time and frequency domain approaches in airborne electromagnetics, which is why the system was originally designed. To the best of our knowledge, EQUATOR is the only system to collect electromagnetic data both in time and in frequency domains. We further explain the difference between the two methods on some numerical and field examples. Also we describe some advantages of their coupling. In particular, by virtue of our approach, a numerically more robust solution of the one-dimensional electromagnetic inverse problem may be achieved. The recorded full-time measurements are further converted to in-phase, quadrature and off-time responses, as opposed to standard frequency or time domain solutions, which have been widely adapted within the industry. When inverting the data, our main focus is within the top 100 m of the Earth, which are the most relevant for engineering and environmental studies. We emphasize that a combined use of frequency and time domain data gives more detailed information about geological structures in the near-surface. As an example, we present some case studies obtained over a platform (Siberia) and a crystalline shield (Western Africa) setting. We further suggest using these results in such near-surface studies as sediment thickness estimation, soil state analysis, groundwater search, and geological structural analysis.

Frequency and time domain analyses of sensor signals in drilling—I. Correlation with drill wear

Automatic speech recognition (ASR) systems have been widely deployed in modern smart devices to provide convenient and diverse voice-controlled services. Since ASR systems are vulnerable to audio replay attacks that can spoof and mislead ASR systems, a number of defense systems have been proposed to identify replayed audio signals based on the speakers' unique acoustic features in the frequency domain. In this paper, we uncover a new type of replay attack called modulated replay attack, which can bypass the existing frequency domain based defense systems. The basic idea is to compensate for the frequency distortion of a given electronic speaker using an inverse filter that is customized to the speaker's transform characteristics. Our experiments on real smart devices confirm the modulated replay attacks can successfully escape the existing detection mechanisms that rely on identifying suspicious features in the frequency domain. To defeat modulated replay attacks, we design and implement a countermeasure named DualGuard. We discover and formally prove that no matter how the replay audio signals could be modulated, the replay attacks will either leave ringing artifacts in the time domain or cause spectrum distortion in the frequency domain. Therefore, by jointly checking suspicious features in both frequency and time domains, DualGuard can successfully detect various replay attacks including the modulated replay attacks. We implement a prototype of DualGuard on a popular voice interactive platform, ReSpeaker Core v2. The experimental results show DualGuard can achieve 98% accuracy on detecting modulated replay attacks.

BackgroundIn investigations of the human motor system, two approaches are generally employed toward the identification of common modulating drives from motor unit recordings. One is a frequency domain method and uses the coherence function to determine the degree of linear correlation between each frequency component of the signals. The other is a time domain method that has been developed to determine the strength of low frequency common modulations between motor unit spike trains, often referred to in the literature as 'common drive'.MethodsThe relationships between these methods are systematically explored using both mathematical and experimental procedures. A mathematical derivation is presented that shows the theoretical relationship between both time and frequency domain techniques. Multiple recordings from concurrent activities of pairs of motor units are studied and linear regressions are performed between time and frequency domain estimates (for different time domain window sizes) to assess their equivalence.ResultsAnalytically, it may be demonstrated that under the theoretical condition of a narrowband point frequency, the two relations are equivalent. However practical situations deviate from this ideal condition. The correlation between the two techniques varies with time domain moving average window length and for window lengths of 200 ms, 400 ms and 800 ms, the r2 regression statistics (p < 0.05) are 0.56, 0.81 and 0.80 respectively.ConclusionsAlthough theoretically equivalent and experimentally well correlated there are a number of minor discrepancies between the two techniques that are explored. The time domain technique is preferred for short data segments and is better able to quantify the strength of a broad band drive into a single index. The frequency domain measures are more encompassing, providing a complete description of all oscillatory inputs and are better suited to quantifying narrow ranges of descending input into a single index. In general the physiological question at hand should dictate which technique is best suited.

Physiological signal is readings or measurements that collect from the human body through various sensors. These signals are easily contaminated by noise and usually contain both nonperiodic and periodic components. As a new transform analysis method, wavelet transform can automatically adapt to the requirements of time-frequency signal analysis to focus on any details of the signal. This paper takes ECG as an example to discuss the application of wavelet transform to physiological signal analysis. Also, the experimental results show that the Gaussian wavelets family is suitable for physiological signal analysis.

Influence of water activity on acoustic emission of flat extruded bread

An improved mathematical model describing acoustic emission (AE) signals generated by different types of partial discharges (PD) that occur in electric power transformer insulation system is presented in the paper. AE signals are analyzed within the AE method as applied for power transformer failure detection due to occurrence of PD. There are several types of basic defects, which are characterized by different types of PD. The mathematical model presented here is crucial for numerical analyses and simulations, where it acts as the function describing the acoustic source in an acoustic model of power transformer insulation system. The regression procedure was performed based on empirical AE signals, registered in a laboratory experiment. The AE signals are described by a mathematical model being a multi-parameter function, which involve both the time domain and the frequency domain. Goodness of the model was evaluated based on analysis of 480 data samples in the time, frequency and time-frequency domains. Also coherence between the registered and modeled signals was calculated. It was stated that the improved model fits very well to the real data, although, due to high level of noise embodied in signals registered in experiments, the coherence values remain low. Moreover, analyses of the estimated data were performed and some example results are presented in this paper. Based on the achieved outcomes a collection of parameter values was prepared for each of the eight considered PD basic types. One can simple use it now in a numerical model for simulation of AE signal source generated by specified type of PD, what corresponds to a particular power transformer insulation system failure. Furthermore, the regression procedure presented in this paper can be easily transferred to any other types of AE sources including processes of compression, tension and cracking.

Accurately assessing the driver's mental workload is of great significance to reduce the traffic accidents caused by the driver's mental overload. This study aims to evaluate drivers' mental workload in simulated typical driving scenarios, with <italic>N</italic>-back cognitive tasks used to manipulate varied levels of task difficulty. We collect data on multi-modal physiological signals including electroencephalogram (EEG), electrocardiogram (ECG), and electrodermal activity (EDA) signals, and subjective mental load of the National Aeronautics and Space Administration task load index (NASA_TLX) during the task completion process of the driver in the experiment, and propose a series of mental workload classification models based on feature analysis and pattern recognition of the multi-modal physiological signals. These classification models are verified by machine learning algorithms of random forest, decision tree and <italic>k</italic>-nearest neighbor models. The results show that the accuracy of classification models varies with different modalities of physiological signals. EEG-based classification models yield the highest accuracy among single-modal classification models, followed by EDA-based and ECG-based models. Multi-modal-based classification models generally perform better than single-modal classification models. The random forest classification algorithm based on three-modal physiological signals of EEG, ECG and EDA has the highest classification accuracy.

In this article, theoretical modeling and simulations are introduced to explore the contact failure characteristics for connectors both in time and frequency domains. The equivalent models are developed to describe the impedance performances of un‐degraded and degraded connectors with the time domain and frequency domain, respectively. The experiments using a Network Analyzer for time and frequency domains analyses are conducted to verify the proposed models. The measured results agree well with the simulation results in the time and frequency domains.

We study here three topics in Ultra-Wideband Antennas. First, we consider a standard for characterizing antenna performance in the time domain, We develop a single time domain function, called antenna impulse response, which fully describes antenna performance with equations that are as simple as possible in both the frequency and time domains. Next, we survey the available large UWB antennas, primarily consisting of variations of Impulse Radiating Antennas. These consist of a reflector and a wideband feed, and are capable of nearly two decades of bandwidth; or a 100:1 band ratio. Finally, we review the status of time domain UWB antenna ranges, which can be used to characterize both wideband and narrowband antennas in both the time and frequency domains. Such systems also measure the impulse response of an antenna.

The clinical environment is filled with various types of physiological signals, and with the current rapid pace of advances in medical technology, there is a demand for an organized way to analyze these signals. Physiological signals have evolved from just periodic recording of absolute values from the patient. Signals now include predictive trends and clinical decision support, waveform analysis, and continuous monitoring. There are numerous physiological signals needing to be recorded from one patient, and just organizing how to record the data is only the first step. A meaningful physiological signal database needs to also be created and cannot contain just “data dumps” but needs to be organized in a robust manner for ease of future retrieval and clinically significant analysis. The appropriate understanding and management of physiological signals is necessary for future research purposes as well as the quality and efficiency of modern healthcare.

Epilepsy is a serious chronic neurological disorder and it can be detected by analyzing an Electroencephalogram acquired from non-invasive methods. Different strategies have been used for the identification of frequencies in EEG signals and the detection of an epileptic seizure, and also for the analysis in the time domain. This paper presents a comparative review of three of the most widely used methods for the analysis of EEG signals in the time and frequency domain: Fourier Transform, Wavelet Transform, and Hilbert Huang Transform. The results presented are obtained from real databases of patients diagnosed with epilepsy.