Quantum dots printing paste for display backlights: Preparation, characterization, and applications

In this study, white organic light-emitting diodes (OLEDs) consisting of red quantum dots (RQD) and green quantum dots (GQD) were investigated. These are the most exciting new lighting technologies that have grown rapidly in recent years. The white OLED development processes used consisted of the following methods: (a) fabrication of a blue single-emitting layer OLED, (b) nanoimprinting into QD photoresists, and (c) green and red QD photoresists as color conversion layers (CCL) excited by blue OLEDs. To fabricate the blue OLED, the HATCN/TAPC pair was selected for the hole injection/transport layer on ITO and TPBi for the electron transport layer. For blue-emitting material, we used a novel polycyclic framework of thermally activated delayed fluorescence (TADF) material, ν-DABNA, which does not utilize any heavy metals and has a sharp and narrow (FWHM 28 nm) electroluminescence spectrum. The device structure was ITO/HATCN (20 nm)/TAPC (30 nm)/MADN: ν-DABNA (40 nm)/TPBi (30 nm)/LiF (0.8 nm)/Al (150 nm) with an emitting area of 1 cm × 1 cm. The current density, luminance, and efficiency of blue OLEDs at 8 V are 87.68 mA/cm2, 963.9 cd/m2, and 1.10 cd/A, respectively. Next, the bottom emission side of the blue OLED was attached to nanoimprinted RQD and GQD photoresists, which were excited by the blue OLED in order to generate an orange and a green color, respectively, and combined with blue light to achieve a nearly white light. In this study, two different excitation architectures were tested: BOLED→GQD→RQD and BOLED→RQD→GQD. The EL spectra showed that the BOLED→GQD→RQD architecture had stronger green emissions than BOLED→RQD→GQD because the blue OLED excited the GQD PR first then RQD PR. Due to the energy gap architectures in BOLED-GQD-RQD, the green QD absorbed part of the blue light emitted from the BOLED, and the remaining blue light penetrated the GQD to reach the RQD. These excited spectra were very close to the white light, which resulted in three peaks emitting at 460, 530, and 620 nm. The original blue CIE coordinates were (0.15, 0.07). After the excitation combination, the CIE coordinates were (0.42, 0.33), which was close to the white light position.

This work presents a multiphase multilamp driving system for liquid crystal display (LCD) back light The driving system adopts a multiphase inverter to drive cold cathode fluorescent lamps (CCFL) to reduce input current ripple. Furthermore, to prevent current imbalance among lamps a multiphase transformer is introduced in the proposed system. Compared with the conventional single-phase driving system, the proposed one can have the merit of requiring less number of transformers. A three-phase driving system with current balancing transformer has been built, from which experimental results have verified the feasibility of the proposed multiphases driving system.

This paper proposes high performance control of light emitting diode(LED) drive system for liquid crystal display(LCD) backlight. The CCFL(cold cathode fluorescent lamp)was used to a conventional LCD backlight. Due to improvement on luminous efficiency, long life and wide color gamut, LED has gradually substituted for CCFL as backlight. The backlight using LED is necessary to use many LED. For that reason, the LED backlight is using a lot of LED driving circuits. The many LED driving circuit is generated a current deviation between LED. Eventually, it is caused brightness deviation between LED. Therefore, this paper improves the current deviation using transformer and balancing capacitor to solve this problem. Also, for accurate and uniform brightnesss control, this paper is applied the artificial intelligent control to a dimming control. This paper is compared with conventional system, and validity of this paper proves through that result.

Quantum dot materials have the characteristics of narrow luminescence spectrum, adjustable luminescence wavelength and high fluorescence quantum yield. The quantum dot LEDs have more potential in improving color gamut. In this paper, a method of white light generation by blue LED excited CdSe red and green quantum dots is introduced. The ratio of red and green quantum dots to glue was (1:60) and (1:10), and the test range of glue content was 1.4 μL~2.2 μL and 3.0 μL~5.0 μL. The samples were prepared by traditional method and layered structure. The absorption and conversion ratio of blue light in the range of glue amount were tested. The function relationship between glue amount and absorption and conversion was obtained by Matlab fitting. When taking the dots (0.34, 0.3) in white light region formed in the above test glue amount range, the red and green quantum dots were calculated with glue amount of 1.9 μL and 4.55 μL, and the corresponding theoretical spectrum was established according to the spectral calculation formula. According to the above glue amount, the verification samples were made and tested the color coordinates (0.3409, 0.2992) and the homologous spectra were basically coincident with the theoretical spectra.

Thermal effects were investigated in a liquid crystal display (LCD) backlight unit (BLU) that was composed of light emitting diode (LED) arrays. The driving power for a single LED in a BLU is determined by the desired brightness of the LCD panel and the pitch distance between adjacent LEDs. As the pitch distance increases, individual LEDs need to be driven by a higher power in order to maintain the same brightness. Since the junction temperature of an LED plays an important role in LED performance, such as optical efficiency, intensity degradation, and lifetime, the maximum driving power for an LED should be limited by a critical level of the junction temperature. A guideline for designing LED BLU panels taking account of the junction temperature is presented using various parameters of LED arrays.

Quantum dot-based diabetic foot mapping for diagnosing osteomyelitis and Charcot neuroarthropathy

In this paper, a novel hardware-oriented adaptive local dimming backlight control algorithm is proposed for very large-scale integration implementation. The proposed algorithm includes a novel dimming algorithm to save energy of the liquid crystal display (LCD) backlight module and a novel contrast enhancement algorithm to compensate the dimming of brightness in displaying images. In order to improve the power-saving rates and image quality, a block-based model and a Gaussian distribution model were added. After obtaining a clipped point by the Gaussian distribution model, a pixel compensator was used to compensate the brightness value of each pixel to satisfy the human vision. In the meantime, a power width modulation module produced power control signal for the LCD backlight module. To meet the performance standards for displaying video in real time, the proposed algorithm was implemented by an eight-stage pipelined architecture. In addition, a new color-space YEF transform composed of integer adders and shifters was used to realize the grayscale converter to replace floating point multipliers. Moreover, the high-complexity operations, such as square root, multiplication, and division, required for the Gaussian distribution model were simplified by using a lookup table technique, which could reduce the hardware cost of the proposed design efficiently. This design was fabricated by a TSMC 0.18-μm CMOS process, and the chip area is 630 105 μm2. Compared with previous local dimming backlight control algorithms, this work improved the average peak signal to noise ratio by 6.89 dB and saved 7.61% more backlight power consumption than previous studies.

Luminescent thermal stability and electronic structure of narrow-band green-emitting Sr-Sialon:Eu2+ phosphors for LED/LCD backlights

This work reported on synthesis of highly efficient, color-pure green- and red-emitting non-Cd InP/ZnS core/shell quantum dots (QDs) and their utilization as color converters for the fabrication of display backlighting QD-based white light-emitting diode (LED). Green and red QD emitters were first individually embedded into a transparent polymeric matrix of polyvinylpyrrolidone and the resulting two free-standing QD composite plates were then physically combined into a bilayered form. White QD-LED was fabricated by remotely loading the bilayered QD plate of a red-on-green configuration onto blue LED chip. This remote-type white device generated a spectrally well-resolved, tricolored electroluminescent spectrum, and exhibited luminous efficacies of 8.9−16.7 lm/W, depending on forward currents of 20−100 mA, and a high color gamut of 87%.

This paper experimentally shows how the center wavelength and spectral power distribution (SPD) of displayed color is related to chromostereopsis. Chromostereopsis - a visual illusion whereby the impression of depth is conveyed in two-dimensional color images - can be applied to glassless binocular stereopsis by controlling color saturation even when a commercial liquid crystal display (LCD) is used to display a two-dimensional image. We conducted evaluations of stereoscopic visual effects among monochrome images using an LCD panel and three monochrome backlights whose SPD had a single peak. The center wavelength and full width at half maximum (FWHM) of the SPD for the backlight were varied. The experimental results show that chromostereopsis does not occur strongly when the FWHM of a backlight is larger than 100 nm. We also suggest that the impression of the depth for monochrome images depends on the center wavelength and FWHM of the color, which indicates chromostereopsis can be expressed by the chromatic aberration.

A highly luminescent and photostable quantum dot-silica monolith (QD-SM) substance was prepared by preliminary surface exchange of the QDs and base-catalyzed sol-gel condensation of silica. The SM was heavily doped with 6-mercaptohexanol exchanged QDs up to 12 vol % (26 wt %) without particle aggregation. Propylamine catalyst was important in maintaining the original luminescence of the QDs in the SM during sol-gel condensation. The silica layer was a good barrier against oxygen and moisture, so that the QD-SM maintained its initial luminescence after high-power UV radiation (∼1 W) for 200 h and through the 150 °C LED encapsulant curing process. Green and red light-emitting QD-SMs were applied as color-converting layers on blue LEDs, and the external quantum efficiency reached up to 89% for the green QD-SM and 63% for the red one. A white LED made with a mixture of green and red QDs in the SM, in which the color coordinate was adjusted at (0.23, 0.21) in CIE1931 color space for a backlight application, showed an efficacy of 47 lm/W, the highest value yet reported.

Switching the liquid crystal display (LCD) backlight of a portable multimedia device to a low power level saves energy but results in poor image quality especially for the low-luminance image areas. In this paper, we propose an image enhancement algorithm that overcomes such effects of dim LCD backlight by taking the human visual property into consideration. It boosts the luminance of image areas below the perceptual threshold while preserving the contrast of the other image areas. We apply the just noticeable difference theory and decompose an image into an HVS response layer and a background luminance layer. The boosting and compression processes, which enhance the visibility of the low-luminance image areas, are carried out in the background luminance layer to avoid luminance gradient reversal and over-compensation. The contrast of the processed image is further enhanced by exploiting the Craik-O'Brein-Cornsweet visual illusion. Experimental results are provided to show the performance of the proposed algorithm.

When the size of a liquid crystal display (LCD) increases, the light guiding plate (LGP) as the main part of the LCD must adopt a wedge-shaped plate to reduce its weight (the thickness of the LGP decreases because of this) and guide the light to the LCD screen. Micro-injection molding (MIM) is commonly used to manufacture LGPs. During the filling phase of MIM, the entire entering polymer melt front of the LGP should reach the end of the mold cavity at the same time. In this way, there will be no shrinkage or warpage of the LGP in its subsequent application, but it is difficult for the wedge-shaped LGP to meet these requirements. Therefore, the authors hoped to investigate MIM process parameters to change this situation. Otherwise, the LGP is easily deformed during the manufacturing process. Flow characteristics of LGPs were investigated during the filling phase of MIM in this study. Experimental and 3D numerical simulations were used to analyze the hysteresis, i.e., the advance of the polymer melt front of the LGP in MIM. Study results showed that a low injection speed caused a hysteresis effect of the plastic melt front, the solution was to increase the injection speed to improve the situation and an injection speed of 10 cm/s could achieve uniformity of the melt front in MIM. The research results showed that the filling situation of the LGP of MIM in the experiment was very close to that of the 3D numerical simulation.

The display contrast and efficiency of power consumption for LCDs (Liquid Crystal Displays) continue to attract attention from both industry and academia. Local dimming approaches for direct-type backlight modules (BLMs, also referred to as backlight units, BLUs) are regarded as a potential solution. The purpose of this study is to explore how to optimize the local dimming method of LCD to achieve higher contrast and lower power consumption through deep learning techniques. In this paper, we propose a local dimming approach with dual modulation for LCD-LED displays based on VGG19 and UNet models. Experimental results have shown that this method not only reconstructs the input image into an HDR (High Dynamic Range) image but also automatically generates a control image for the backlight module and LCD panel. In addition, the proposed method can effectively improve the contrast and reduce the power consumption of the LCD in the absence of a public training dataset. Our method can achieve the best performance in MSE and HDR-VDP-2 among eight different combinations of mask and pre-training. Using deep learning techniques, this study has successfully optimized the local dimming approach of LCDs and demonstrated its benefits in improving contrast and reducing power consumption.

We propose two polarization interference filters (PIF1 and PIF2) used in the backlight unit of a liquid crystal display (LCD) to achieve a wide color gamut. Both PIF1 and PIF2 consist of two polarizers and two 720° super twisted nematic liquid crystal polymer (LCP) layers, where two polarizers are crossed in PIF1, and two polarizers are parallel in PIF2. The PIFs can eliminate unwanted cyan and yellow parts in the output spectrum, which can improve the color gamut of LCD. In our calculation, when the PIF1 is employed in the LCD with normal color filter and QD-LED backlight, the color gamut increases from 107.3% NTSC to 124.6% NTSC, which is 13.7% NTSC larger than that of the LCD with high-performance color filter. When the PIF2 is employed in the LCD with normal color filter and QD-LED backlight, the color gamut of LCD with a normal color filter is improved by 6.8% NTSC larger than that of LCD with high-performance color film, and the transfer efficiency is close to that of the LCD with high-performance color film. We define the color gamut enhancement ratio (CGER) to compare the influence of PIFs and the high-performance color filter on the color gamut enhancement performance of LCD. Compared with the high-performance color filter, the two kinds of PIFs have a higher CGER. The PIFs have a great potential for achieving a wide color gamut.