RadarPDR: Radar-Assisted Indoor Pedestrian Dead Reckoning

Pedestrian Dead Reckoning (PDR), which comes with many sensors integrated into widely available smartphones, is known as one of the most popular indoor positioning techniques. Sensors such as accelerometers, gyroscopes, and magnetometers are used to determine three important components in PDR: step detection, step length estimation, and heading estimation. Among them, the last component is the most challenging since a small heading error accumulates to produce a very large positioning error, especially when the pedestrian holds the smartphone in unconstrained styles such as swinging the phone freely along the pedestrian’s walking direction or putting the phone into the pants’ front pockets. The research proposes an adaptive heading estimation method to deal with heading errors caused by smartphone holding styles. The novelties are described as follows. Firstly, the proposed method attempts to classify the four basic smartphone holding styles using a machine learning algorithm based on simple features of acceleration values to give pedestrians more freedom during the walking period. Secondly, the proposed method adaptively combines the two heading estimation methods, which are calculated from the integrated sensors, to determine the walking direction for different smartphone holding styles. The experimental results show that the proposed heading estimation method achieves average heading errors of less than 30 degrees when testing in two different walking paths with the smartphone held in dynamic styles. It helps to reduce the heading errors by more than 15% compared to previous heading estimation methods.

In recent years, the demand for location based service has promoted the rapid development of pedestrian navigation and positioning technology. Among them, Pedestrian Dead Reckoning (PDR) based on inertial sensor can greatly improve the robustness of indoor and outdoor pedestrian navigation system due to its environment-friendly. This paper designs a robust PDR algorithm based on smart phone. This paper constructs multi-level constraints based on INS algorithm and establishing observation equation needed by EKF using the mutually complementary relationship among sensors, such as gyroscope accelerometer and magnetometer, and human dynamic model. The cumulative error of the system is less than 2% of the traveling distance when using different intelligent terminals, holding on hand both in indoor and outdoor test.

Substations are critical infrastructures in modern power systems, requiring accurate and reliable personnel positioning to ensure operational safety and inspection efficiency. Pedestrian dead reckoning (PDR) technology has emerged as a preferred solution for real-time seamless positioning due to its autonomous, anti-jamming and passive characteristics. However, in practical applications, the PDR algorithm faces challenges such as the inability to provide absolute positioning due to unknown starting points and cumulative errors over time. To address these challenges, this paper proposes a head-mounted pedestrian positioning system (HPPS) integrating fisheye camera/real-time kinematic (RTK)/PDR based on factor graph optimization (FGO). First, a skyward-facing fisheye camera identifies non-line-of-sight (NLOS) signals caused by architectural obstructions, improving the absolute positioning accuracy of RTK. Next, an adaptive pedestrian gait detection and step length estimation algorithm based on head-mounted inertial measurement units (IMU) is developed to enhance PDR robustness. Finally, the FGO framework integrates the inputs of the fisheye camera, RTK, and PDR to achieve seamless indoor-outdoor positioning. Experimental results demonstrate that the proposed system achieves horizontal root mean square error (RMSE) values of less than 0.42 m and 0.35 m in two distinct outdoor substation environments and less than 1.36 m in indoor-outdoor scenarios. This work highlights the integration of precise positioning technologies within the Internet of Things (IoT) framework, advancing smart grid applications and enabling effective location tracking in complex environments.

WiFi-based indoor positioning is widely exploited thanks to the existing WiFi infrastructure in buildings and built-in sensors in smartphones. The techniques for indoor positioning require the high-density training data to archive high accuracy with high computation complexity. In this paper, the approach for indoor positioning systems which is called the maximum convergence algorithm is proposed to find the accurate location by the strongest receiver signal in the small cluster and K nearest neighbours (KNN) of other clusters. Also, the K-mean clustering is deployed for each access point to reduce the computation complexity of the offline databases. Moreover, the pedestrian dead reckoning (PDR) method and Kalman filter with the information from the received signal strength (RSS) and inertial sensors are applied to the WiFi fingerprinting to increase the efficiency of the mobile object's position. The different experiments are performed to compare the proposed algorithm with the others using KNN and PDR. The recommended framework demonstrates significant proceed based on the results. The average precision of this system can be lower than 1.02 meters when testing in the laboratory environment with an area of 7x7 m using three access points.

In recent years pedestrian dead reckoning (PDR) has been a popular indoor localization technique that takes advantage of inertial navigation sensors (INS) of smartphones due to its availability. Despite the convenience of INS, noise has been a recurring problem in PDR which encourages many researches on noise filtering. This paper proposes a model that utilizes empirical mode decomposition (EMD) as the noise filter. EMD is an unconventional filter being applied in PDR to remove noise by processing the raw signal before implementing step counts, step lengths and heading estimation. The experiment made using the proposed model was able to perform the standard PDR technique without overlaps in heading estimation.

The use of wearable foot-based inertial measurement units (IMUs) incorporated in a navigation system can address the problem of single-person location tracking in situations and environments where GPS signals may be unavailable or inconsistent; e.g., in buildings. This Pedestrian Dead Reckoning (PDR) approach, which enables standalone personal tracking, is an idea that has been attempted many times with varying degrees of success. There are two main approaches to solve this difficult problem: the first is to use inertial measurement units (IMUs) in a filter to apply stride-length, heading correction, and zero-velocity updates to a Kalman filter to get a position solution, while the other is to use Machine Learning techniques to better identify and classify a person’s movement to achieve an accurate position. This paper continues on the path of the former method by investigating the feasibility of PDR using a pair of low cost IMUs along with a pair of relative position and attitude magnetic sensors connected to an individual’s feet. Laverne, et al., [1] have shown that incorporating a ranging measurement between two IMU-based foot sensors significantly increases the accuracy of the pedestrian dead reckoning (PDR) solution. This work will be utilizing a solution more desirable for wearable PDR applications by incorporating smaller, low cost, commercial grade IMUs. To compensate for this degradation in quality, the ranging sensor is replaced with two small magnetic sensors that provide a 6 degree-of-freedom relative pose estimate between the sensors. In addition to a ranging measurement, this paper will introduce the use of a relative rotation measurement update to assist with drift reduction.

Commonly used Global Navigation Satellite Systems (GNSS) are inappropriate as Location Based Services (LBS) in indoor environment. Therefore research teams are developing different systems, which can be used as a suitable alternative. One of options is to use Inertial Navigation System (INS) which consists of inertial sensors and mathematic procedures. This concept has been known for a long time, but with arrival of Microelectro Mechanical System (MEMS) INS found wide use. Smartphones with inertial sensors, such as accelerometers and gyroscopes, allow us to use them as input devices for Pedestrian Dead Reckoning (PDR). In this paper we present PDR by using smartphone sensors. They can be classified as low-cost Inertial Measurement Unit (IMU), and have been compared with more precise and expensive Xsens IMU. Accuracy of inertial sensors has increased in the past few years, but they still cannot alone provide proper accuracy because of many negative effects, such as heading drift due to gyroscope bias. Particle Filter (PF) has been successfully used with map constraints to increase the accuracy of proposed location system. Presented results show that low-cost smartphone IMU combined with PF can be applicable as proper navigation system.

This paper provides a hybrid approach between Wi-Fi and pedestrian dead reckoning (PDR) for the iPhones in indoor environments, and addresses the following two problems. First, since Apple Inc. no longer provides public information about currently-connected Wi-Fi (e.g., service set identifier, received signal strength and channel), Wi-Fi based pedestrian tracking apps that run on the iPhones are more restricted compared to other ones on the Android platforms. Second, even the PDR approach provides such a great way for self-localization, it suffers from accumulated errors of inertial sensors embedded in the smartphones. We propose a conversion function from a Wi-Fi status value to a proximity for the localization purpose. Then, a mobile iPhone collects mobility information from inertial measurements unit (IMU), inputs to the PDR, and combines with Wi-Fi proximity in order to perform accurate self-localization and tracking. Moreover, we improve the PDR by reducing drifting effects caused by the IMU biases. Experiment results show that the proposed scheme is effective and has low complexity, while bringing the benefits from smartphone IMU.

A Map aided Pedestrian Dead Reckoning (PDR) algorithm is proposed to mitigate the drift errors and step detection limitations of pedestrian dead reckoning algorithm with handheld sensors in indoor and outdoor spaces. Specific to this context is the changing lever-arm between the handheld device and the pedestrian center of mass that introduces a misalignment between the inertial sensors and the walking directions. To address these challenges, an adaptive routing graph is built based on possible pedestrian's motions, which depend on personal mobility profile and surroundings. An adaptive decision process is also developed to fuse map data with GNSS positions and PDR outputs in a particle filter. The performance is assessed with 1km walk experiments. Main contributions are (1) the calibration of the PDR step length model using both GNSS and map data during straight line travels with miss/over-detected steps modeled by the particle filter; (2) the estimation of angular misalignment between the walking and the handheld unit pointing directions in geometrically constrained areas; (3) a dynamic choice of opportune periods and measurements to calibrate the PDR outputs and improve the positioning process.

Recently various indoor positioning techniques have been developed based on smartphone. However, most of them need external signals. In this paper a self-contained approach relying on built-in inertial sensors is implemented. Taking advantage of Pedestrian Dead Reckoning, it updates the current position by measuring the length and the heading of each step. Foremost the whole walking process is divided into segments, in which only straight walking is involved. After that the Feature Vectors are extracted for step detection. Specially, to cope with the instabilities caused by gait change, an equivalent Model Wave is created to substitute the original data. Finally, Particle Filter is employed for map matching. According to a group of experiments, our approach is as accurate as traditional positioning technique but shows more robustness.

Abstract. With the continuous improvement of the hardware level of the inertial measurement unit (IMU), indoor pedestrian dead reckoning (PDR) using an inertial device has been paid more and more attention. Typical PDR system position estimation is based on acceleration obtained from accelerometers to measure the step count, estimate step length and generate the position with the heading received from angular sensors (magnetometers and gyroscopes). Unfortunately, collected signals are very responsive to the alignment of sensor devices, built-in instrumental errors and distortions from the surrounding environment. In our work, a pedestrian positioning method using step detection based on a shoe-mounted inertial unit is arranged and put to the test, and the final results are analyzed. The extended Kalman filter (EKF) provides estimation of the errors which are acquired by the XSENS IMU sensor biases. The EKF is revised with acceleration and angular rate computations by the ZUPT (zero velocity update) and ZARU (zero angular rate update) algorithms. The step detection associated with these two solutions is the perfect choice to calculate the current position and distance walked and to estimate the IMU sensors' collected errors by using EKF. The test with a shoe-mounted IMU device was performed and analyzed in order to check the performance of the recommended method. The combined PDR final results were compared to GPS/Beidou postprocessing kinematic results (outdoor environment) and to a real route which was prepared and calculated for an indoor environment. After the comparison, the results show that the accuracy of the regular-speed walking under ZUPT and ZARU combination in the case of outdoor positioning did not go beyond 0.19 m (SD) and for indoor positioning accuracy did not exceed 0.22 m (SD). The authors are conscious that built-in drift errors coming from accelerometers and gyroscopes, as well as the final position obtained by XSENS IMU, are only stable for a short time period. Based on this consideration, our future work will be focused on supporting the methods presented with radio technologies (WiFi) or image-based solutions to correct all IMU imperfections.

As the global navigation satellite system (GNSS) faces the problems of signals blocked by various objects and absorbed by many materials in indoor environments, many indoor positioning methods based on smartphones' inertial measurement unit (IMU) become increasingly applicable. Pedestrian dead reckoning (PDR) as one of the most universal methods, several algorithms with high accuracy have been proposed based on it. However, many algorithms are only applicable to scenes where pedestrians are in the “going forward” state. When the pedestrian's motions include complex patterns such as sidestepping and walking backward, PDR will not work normally as the estimated result is far from the real trajectory. In this paper, we design a deep learning model assisted PDR algorithm to recognize the pedestrian's complex motion patterns (going forward, walking backward, left sidestepping, right sidestepping) from the smartphones' IMU. We firstly employ one combined model of trained convolution neural network (CNN) and long short-term memory (LSTM) neural network to determine the correction angle for different motion patterns. Then, we estimate the pedestrian's motion direction by adding the correction angle to the attitude estimated by the inertial navigation system (INS) mechanization. Finally, the position can be computed by the estimated stride length and the corrected motion direction. Compared with different algorithms, the experimental results have proved that our algorithm can effectively process data in complex motion patterns.

The demand for pedestrian navigation has increased along with the rapid progress in mobile and wearable devices. This study develops an accurate and usable Step Length Estimation (SLE) method for a Pedestrian Dead Reckoning (PDR) system with features including a wide range of step lengths, a self-contained system, and real-time computing, based on the multi-sensor fusion and Fuzzy Logic (FL) algorithms. The wide-range SLE developed in this study was achieved by using a knowledge-based method to model the walking patterns of the user. The input variables of the FL are step strength and frequency, and the output is the estimated step length. Moreover, a waist-mounted sensor module has been developed using low-cost inertial sensors. Since low-cost sensors suffer from various errors, a calibration procedure has been utilized to improve accuracy. The proposed PDR scheme in this study demonstrates its ability to be implemented on waist-mounted devices in real time and is suitable for the indoor and outdoor environments considered in this study without the need for map information or any pre-installed infrastructure. The experiment results show that the maximum distance error was within 1.2% of 116.51 m in an indoor environment and was 1.78% of 385.2 m in an outdoor environment.

This study presents a smart-phone-based hybrid indoor localisation system (HILS), which integrates two different localisation approaches, i.e., pedestrian dead reckoning (PDR) and Wi-Fi-based localisation to compensate the limits of each other. In PDR, the localisation accuracy degrades continuously when the moving distance increases from the starting reference point. However, Wi-Fi-based trilateration method requires the Wi-Fi signals from at least three access points (APs). In this study, the authors propose a more efficient novel Heron-bilateration-based position determination (HBPD) technique, which requires the Wi-Fi signals from only two APs to locate the mobile device. The proposed HILS utilises the HBPD technique to reset the bias drift errors involved with inertial sensors, and compensate the unavailability of strong Wi-Fi signals from APs using the PDR method. In this work, an experimental testbed is developed to collect the Wi-Fi signals and evaluate the proposed method. The proposed HILS is also compared with five other benchmark methods for two different trajectories and the experimental results show that the mean localisation error is decreased up to 1.68 and 1.96 m, which indicate the improvement by 16.83 and 20.97% for both the trajectories, respectively, in comparison with the best performing method among the benchmark methods.

Smartphone-based indoor localization has attracted considerable attentions in both research and industrial areas. However, the localization accuracy and robustness are still challenging problems due to low-cost noisy devices, especially in those complicated localization environments. Considering that pedestrian dead-reckoning (PDR) devices are widely equipped in recent smartphones, we propose a novel indoor localization fusing algorithm that integrates both wireless fidelity (WiFi) features and PDR features. By formulating the fusing indoor localization as a recursive function approximation problem, a sliding-window-based displacement scheme is designed to generate a time-series-based feature data set. We further apply the long short-term memory (LSTM) network for data fusion and localization on this data set by taking advantage of its benefits in time-series prediction and characterization. To evaluate the performance of the proposed algorithm, we compare it with state-of-the-art filter-based localization algorithms in three typical movements and three postures of holding smartphones. Extensive experiment results demonstrate the accuracy and robustness of the proposed algorithm in indoor localization, even in some extreme environments.