Reconfigurable Intelligent Surface for NLOS Integrated Sensing and Communications

Reconfigurable intelligent surfaces (RIS) have the ability to steer the electromagnetic (EM) waves to a desired direction. This enables the improvement of the wireless link performance by allowing the illumination of receivers otherwise shadowed by buildings or hills. In this paper, a standards-compliant link-level simulator is developed to study the performance improvement offered by a RIS in 5G New Radio (NR) uplink operating at sub-6 GHz bands. At these frequencies the direct channel between the user and base station is rarely completely blocked, but given the stringent power restrictions of devices, the RIS is utilized for enhancing the coverage performance in the uplink direction. In the studied cases, the transmitter (TX) is close to the RIS and a line-of-sight (LoS) path between the TX and RIS is assumed. The channel between the TX and receiver (RX) is modeled as a non-line-of-sight (NLoS) channel with 5G NR clustered delay line A (CDL-A) profile. Both LoS and NLoS channels between the RIS and RX are considered. Under state-of-the-art system settings, the RIS is shown to increase the symbol error rate link performance by 6 dB. When the performance is measured with coded bit error rate, the performance gain in simulated cases is 1 dB. The coverage enhancement is measured with the throughput as a function of the distance between the TX and RX. The distance at which the maximum possible throughput can be achieved is increased about 5%. The coverage can be further extended if a lower than the maximum throughput is accepted.

Optimizing resource allocation for enhanced urban connectivity in LEO-UAV-RIS networks

Recently, a reconfigurable intelligent surface (RIS) that provides alternative wireless propagation paths (by reflecting an electromagnetic wave from a base station in desired directions) has attracted attention as a key facilitating technology for Beyond 5G and 6G wireless communications. This paper presents an improved path-loss model suitable for RIS-aided wireless communications. Unlike previously reported RIS path-loss models, the proposed model considers more practical electromagnetic phenomena (e.g., the incident and reflected gain patterns of the RIS unit cell, the effective received power at the RIS, the reflection phase error of each unit cell, and the specular reflection loss), by applying rigorous analysis. Furthermore, the accuracy of the proposed path-loss model is validated by extensive experimental measurements using our developed RIS prototype. The prototype consists of 576 phase-reconfigurable unit cells operating at 29 GHz, each of which features two PIN diodes. Each PIN diode is independently controlled to produce the desired phase distributions on the RIS. It is shown that the calculated received power in the proposed path-loss model matches the measurement results within a 1 dB margin across various practical test environments.

In this paper, we investigate the employment of reconfigurable intelligent surfaces (RISs) into vehicle platoons, functioning in tandem with a base station (BS) in support of the high-precision location tracking. In particular, the use of a RIS imposes additional structured sparsity that, when paired with the initial sparse line-of-sight (LoS) channels of the BS, facilitates beneficial group sparsity. The resultant group sparsity significantly enriches the energies of the original direct-only channel, enabling a greater concentration of the LoS channel energies emanated from the same vehicle location index. Furthermore, the burst sparsity is exposed by representing the non-line-of-sight (NLoS) channels as their sparse copies. This thus constitutes the philosophy of the diverse sparsities of interest. Then, a diverse dynamic layered structured sparsity (DiLuS) framework is customized for capturing different priors for this pair of sparsities, based upon which the location tracking problem is formulated as a maximum a posterior (MAP) estimate of the location. Nevertheless, the tracking issue is highly intractable due to the ill-conditioned sensing matrix, intricately coupled latent variables associated with the BS and RIS, and the spatial-temporal correlations among the vehicle platoon. To circumvent these hurdles, we propose an efficient algorithm, namely DiLuS enabled spatial-temporal platoon localization (DiLuS-STPL), which incorporates both variational Bayesian inference (VBI) and message passing techniques for recursively achieving parameter updates in a turbo-like way. Finally, we demonstrate through extensive simulation results that the localization relying exclusively upon a BS and a RIS may achieve the comparable precision performance obtained by the two individual BSs, along with the robustness and superiority of our proposed algorithm as compared to various benchmark schemes.

Reconfigurable Intelligent Surface (RIS) has been considered as a promising technology for 6G networks, which is capable of directionally reflecting the incident signal by adjusting phase shift of its reflecting elements, and thus to achieve beamforming. In this paper, we investigate the potential of employing RIS in dual-functional radar-communication (DFRC) vehicular networks. Considering a vehicle-to-infrastructure (V2I) communication in non-line-of-sight(N-LoS) scenario, where RIS is deployed to establish sensing and communication links, we propose a scheme to optimize the beamforming based on the detected vehicle position for the sake of avoiding the relatively large channel estimation overhead. More specifically, we build a codebook to maintain the optimal phase shift of RIS corresponding to each candidate angle offline, which can be used for detecting the direction of vehicle in N-LoS scenario. In addition, the position-based channel state information (CSI) is introduced and used for maximize the downlink rate. Simulation results show that by deploying RIS in DFRC vehicular networks, the base station can detect the vehicle position in N-LoS scenario and provide it with reliable communication rates without channel estimation.

Energy efficiency (EE) has become a key performance indicator in designing future wireless networks. In this regard, we propose a novel two reconfigurable intelligent surfaces (RISs) assisted coordinated multipoint (CoMP) network, where two RISs cooperate to reduce energy consumption by constructing an intelligent radio environment. Aiming to maximize this system’s energy efficiency (EE), the joint optimization problem on the cooperative beamforming among base stations (BSs) and passive beamforming among RISs, subject to each user’s data rate requirement, is formulated. An alternative optimization algorithm is proposed by decoupling it into a cooperative beamforming subproblem among BSs and a cooperative reflective coefficients design subproblem among RISs. Dinkelbach’s transform and complex fractional programming algorithms are also invoked to transform these two subproblems into convex optimization problems and obtain the optimal solution for each sub-problem. Numerical results validate the proposed algorithm’s feasibility, fast convergence, and flexibility. It also shows that the proposed scheme with cooperative beamforming design for both BSs and RISs outperforms that without RIS and that with randomly initialized RISs.

Reconfigurable Intelligent Surface (RIS) is one of the promising techniques for 6G wireless communications, and recently has also been shown to be able to improve secure communications. However, there is a “double fading” effect in the reflection link between base station and user, thus passive RIS only achieves a negligible secrecy gain in typical communications scenarios. In this letter, we propose an active RIS-aided multi-antenna physical layer secrecy transmission scheme, where the active RIS can amplify the signal actively. Our aim is to minimize the transmit power subject to the constraint of secrecy rate. To solve the non-convex optimization problem, a penalty-based alternating minimization (AltMin) algorithm is proposed to optimize both the beamformer at the transmitter and the reflection matrix at RIS. Simulation results show that active RIS can resist the impact of “double fading” effect effectively, and is more energy efficient than passive RIS.

In this paper, we propose a novel computer vision-based approach to aid reconfigurable intelligent surface (RIS) for dynamic beam tracking and implement the corresponding prototype verification system. A camera is attached at the RIS to obtain the visual information about the surroundings, with which RIS identifies the incident beam direction and the desired reflected beam direction, and then adjusts the reflection coefficients according to the pre-designed codebooks. We build a 20-by-20 RIS running at 5.4 GHz and develop a high-speed control board to ensure the real-time refresh of the reflection coefficients. Meanwhile we implement an independent peer-to-peer communications system to simulate the physical link between the base station and the user equipment. The vision-aided RIS prototype system is tested in two mobile scenarios: RIS works in near-field conditions as a passive array antenna of the base station; RIS works in far-field conditions to assist the communication between the base station and the user equipment. The experimental results show that RIS can quickly adjust the reflection coefficients for dynamic beam tracking with the help of visual information.

With the development of the next generation of mobile networks, new research challenges have emerged, and new technologies have been proposed to address them. On the other hand, reconfigurable intelligent surface (RIS) technology is being investigated for partially controlling wireless channels. RIS is a promising technology for improving signal quality by controlling the scattering of electromagnetic waves in a nearly passive manner. Heterogeneous networks (HetNets) are another promising technology that is designed to meet the capacity requirements of the network. RIS technology can be used to improve system performance in the context of HetNets. This study investigates the applications of reconfigurable intelligent surfaces (RISs) in heterogeneous downlink networks (HetNets). Due to the network densification, the small cell base station (SBS) interferes with the macrocell users (MUEs). In this paper, we utilise RIS to mitigate cross-tier interference in a HetNet via directional beamforming by adjusting the phase shift of the RIS. We consider RIS-assisted heterogeneous networks consisting of multiple SBS nodes and MUEs that utilise both direct paths and reflected paths. Therefore, the aim of this study is to maximise the sum rate of all MUEs by jointly optimising the transmit beamforming of the macrocell base station (MBS) and the phase shift of the RIS. An efficient RIS reflecting coefficient-based optimisation (RCO) is proposed based on a successive convex approximation approach. Simulation results are provided to show the effectiveness of the proposed scheme in terms of its sum rate in comparison with the scheme HetNet without RIS and the scheme HetNet with RIS but with random phase shifts.

In this paper, we propose a location-aware channel estimation based on the atomic norm minimization (ANM) for the reconfigurable intelligent surface (RIS)-aided millimeter-wave multiple-input-multiple-output (MIMO) systems. The beam training overhead at the base station (BS) is reduced by the direct beam steering towards the RIS with the location of the BS and the RIS. The RIS beamwidth adaptation is proposed to reduce the beam training overhead at the RIS, and also it enables accurate channel estimation by ensuring the user equipment receives all the multipath components from the RIS. After the beam training, the cascaded effective channel of the RIS-aided MIMO systems is estimated by ANM. Depending on whether the beam training overhead at the BS or at the RIS is reduced or not, the channel is represented as a linear combination of either 1D atoms, 2D atoms, or 3D atoms, and the ANM is applied to estimate the channel. Simulation results show that the proposed location-aware channel estimation via 2D ANM and 3D ANM achieves superior estimation accuracy to benchmarks.

Energy efficiency (EE) is one of the most important metrics for the beyond fifth generation (B5G) and the future sixth generation (6G) wireless networks. Reconfigurable intelligent surface (RIS) has been widely focused on EE enhancement for wireless networks because it is power-saving, programmable, and easy to be deployed. However, RIS is generally passive and thus difficult to obtain corresponding full channel state information (CSI), which severely impacts the EE enhancement of RIS-assisted wireless communications. To solve this problem, in this paper we propose the new single-active-antenna combined RIS transmitter structure, which can replace traditional multiple antennas to reduce hardware cost and power consumption. Based on the single-active-antenna combined RIS structure, we develop the Dumb RIS-Assisted Random Beamforming (Darb)-based Joint RIS-Elements and Transmit-power optimizAtion (Jeta) scheme, where dumb RIS randomly changes its phase shift according to isotropic distribution only depending on the CSI feedback from users to RIS-assisted transmitter. Then, we jointly design the number of RIS elements and optimize the transmit power to maximize the EE of RIS-assisted wireless communications. Simulation results show that compared with the traditional multi-antenna system, our developed Darb-based-Jeta scheme can significantly increase the EE without the full CSI.

A reconfigurable intelligent surface (RIS) reflects incoming signals in different ways depending on the phase-shift pattern assigned to its elements. The most promising use case is to aid the communication between a base station and a user when the user has a line-of-sight (LOS) channel to the RIS but the direct channel is blocked. The main challenge is to estimate the channel with limited resources because non-parametric estimation methods require a pilot length proportional to the large number of RIS elements. In this paper, we develop a parametric maximum likelihood (ML) channel estimation framework for estimating the LOS channel to the RIS. We demonstrate that the proposed algorithm can accurately obtain the channel and preferred RIS configuration using only a few pilots. A key novelty is that the RIS configurations used during pilot transmission are selected to progressively improve the estimation accuracy.

Integrated sensing and communication (ISAC) has emerged as a promising technology for sixth-generation (6G) communication networks. At the same time, ensuring the privacy of targets in ISAC is important in contexts where a malicious sensor is present. In this paper, we investigate a reconfigurable intelligent surface (RIS)-assisted ISAC system designed to protect a sensing region against an adversarial detector (AD), where the base station (BS) has imperfect knowledge of the AD’s location. The RIS consists of both reflecting and absorptive elements (the latter serving as sensing elements), which can be adaptively reconfigured to meet system requirements. Specifically, the system is designed to maximize the jamming power from the BS to the AD by jointly optimizing the transmit beamformer at the BS, the RIS phase-shift matrix, the receive beamformer at the RIS, and the allocation between reflecting and absorptive elements at the RIS while ensuring a minimum sensing signal-to-interference-plus-noise ratio (SINR) at sample points within the sensing region, as well as a minimum communication SINR for each user. To address this challenging optimization problem, we propose an alternating optimization framework combined with a successive convex approximation method tailored for each subproblem. Our results show that the proposed system model offers significant protection of the sensing area compared to the case where the target privacy is not considered. Simulations also confirm that the proposed adaptive RIS partitioning outperforms the fixed RIS partitioning approach.

Thanks to the recent advances in metamaterials, reconfigurable intelligent surface (RIS) has emerged as a promising technology for future 6G wireless communications. Benefiting from its high array gain, low cost, and low power consumption, RISs are expected to greatly enlarge signal coverage, improve system capacity, and increase energy efficiency. In this article, we systematically overview the emerging RIS technology with the focus on its key basics, nine fundamental issues, and one critical problem. Specifically, we first explain the RIS basics, including its working principles, hardware structures, and potential benefits for communications. Based on these basics, nine fundamental issues of RISs, such as ``What's the differences between RISs and massive MIMO?'' and ``Is RIS really intelligent?'', are explicitly addressed to elaborate its technical features, distinguish it from existing technologies, and clarify some misunderstandings in the literature. Then, one critical problem of RISs is revealed that, due to the ``multiplicative fading'' effect, existing passive RISs can hardly achieve visible performance gains in many communication scenarios with strong direct links. To address this critical problem, a potential solution called active RISs is introduced, and its effectiveness is demonstrated by numerical simulations.

This paper studies the coexistence of enhanced mobile broadband (eMBB) and ultra-reliable and low-latency communication (URLLC) services in a cellular network that is assisted by a reconfigurable intelligent surface (RIS). The system model consists of one base station (BS) and one RIS that is deployed to enhance the performance of both eMBB and URLLC in terms of the achievable data rate and reliability, respectively. We formulate two optimization problems, a time slot basis eMBB allocation problem and a mini-time slot basis URLLC allocation problem. The eMBB allocation problem aims at maximizing the eMBB sum rate by jointly optimizing the power allocation at the BS and the RIS phase-shift matrix while satisfying the eMBB rate constraint. On the other hand, the URLLC allocation problem is formulated as a multi-objective problem with the goal of maximizing the URLLC admitted packets and minimizing the eMBB rate loss. This is achieved by jointly optimizing the power and frequency allocations along with the RIS phase-shift matrix. In order to avoid the violation in the URLLC latency requirements, we propose a novel framework in which the RIS phase-shift matrix that enhances the URLLC reliability is proactively designed at the beginning of the time slot. For the sake of solving the URLLC allocation problem, two algorithms are proposed, namely, an optimization-based URLLC allocation algorithm and a heuristic algorithm. The simulation results show that the heuristic algorithm has a low time complexity, which makes it practical for real-time and efficient multiplexing between eMBB and URLLC traffic. In addition, using only 60 RIS elements, we observe that the proposed scheme achieves around 99.99% URLLC packets admission rate compared to 95.6% when there is no RIS, while also achieving up to 70% enhancement on the eMBB sum rate.