Research on Collision Avoidance Systems for Intelligent Vehicles Considering Driver Collision Avoidance Behaviour

Operations in the Next Generation Air Transportation System (NextGen) are planned to have a reduced dependency on primary surveillance radar and use Automatic Dependent Surveillance - Broadcast (ADS-B) to provide aircraft state information to Air Traffic Control (ATC) and onboard collision detection and avoidance systems. With the ongoing integration of Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS), ADS-B is expected to become the main surveillance input to UAS collision avoidance. Traffic Alert and Collision Avoidance System (TCAS) is unable to meet requirements in terms of adaptability to future operations with reduced separation margins, addition of new user groups (e.g., UAS), and support of additional surveillance inputs. Airborne Collision Avoidance System (ACAS X) is being designed to meet these requirements and to increase surveillance, alerting, and resolution performance. The RTCA has released Minimum Operational Performance Standards (MOPS) to provide system and operational performance characteristics that ADS-B must provide. This paper analyzes recorded ADS-B data from test flights that were performed in the Continental U.S. (CONUS) and verifies measured performance with specified operational characteristics in terms of coverage, accuracy, and integrity.

With the development of marine technology, the research of unmanned surface vehicles (USVs) has received wide attention from the world. Designing effective collision avoidance algorithm in dynamic sea environment is necessary for the navigation of USVs. This paper describes a collision avoidance system (CAS) with COLREGs compliance to improve autonomous navigational ability of USV. For small podded propulsion USV, a three-DOFs maneuvering model is established and the parameters of model are determined by the parameter identification method based on field experiments. About the COLREGs rules, the different maneuvering behaviors are summed up according to encounter situation and collision risk assessment. In the CAS, finite control set model predictive control is adopted, and COLREGs rules are taken as an evaluation standard in the quality function. Finally, the system is verified to avoid multiple dynamic obstacles and compliance vessel in the simulation and real environment, and the results of collision avoidance under four encounter situations are described in detail.

Aims: To enhance the safety of intelligent vehicle drivers and help them achieve active collision avoidance. Background: Existing research on intelligent vehicles’ active collision avoidance focuses on reference path optimization and stability tracking control. However, there is relatively little research on collision avoidance in emergency accident scenarios. Longitudinal emergency braking collision avoidance technology has been relatively mature, while steering collision avoidance still needs a long time to develop. The research on joint steering and braking collision avoidance in emergency situations is still limited. Objective: Modeling the longitudinal and lateral safety distances based on the safety conditions of adjacent lanes, two active collision avoidance strategies are designed, namely the steering strategy and combined lateral and longitudinal collision avoidance strategy, with the aim of reducing the risk of collision. Methods: In the steering strategy, five control points are first determined sequentially according to steering collision constraints. Then, a collision avoidance path is established based on the quartic Bezier curve. To enhance the tracking of this path, an LQR path-tracking controller is employed to reduce errors via feed-forward and feedback control. In the case of a combined lateral and longitudinal collision avoidance strategy, the LQR and PID controllers are first adjusted and optimized, and then the collision avoidance path is replanned. Besides, the safety risks associated with braking and steering are taken into consideration, and constraints are set on the braking deceleration accordingly. Results: The effectiveness of the designed steering strategy and combined lateral and longitudinal collision avoidance strategy is verified through simulation results obtained by using CarSIM and Matlab/Simulink. They can effectively avoid collisions in emergency situations. Conclusion: The proposed collision avoidance algorithm can avoid collision in emergency scenarios and enhance the safety of autonomous driving.

With the development of intelligent waterborne transportation, mining collision avoidance patterns based on spatiotemporal and motion data of ships are crucial for the autonomous navigation of intelligent ships, which requires accurate collision avoidance information under various encounter scenarios. Addressing the existing issues of low precision and false detection in data mining algorithms, this paper proposes a collision avoidance behavior mining model considering encounter scenarios. The model is based on the Automatic Identification System (AIS) and the International Regulations for Preventing Collisions at Sea (COLREGs); it firstly identifies ship collision avoidance turning points by analyzing trajectory curvature with turning and recovering factors. Then, by combining AIS data and the specific navigational environment, it matches the ship encounter pairs and determines the encounter scenarios. Comparative experiments show that the model demonstrates superior accuracy in various scenarios compared to traditional algorithm. Finally, the model was applied to AIS data east of the Yangtze River Estuary, recognizing a total of 827 instances of ship collision avoidance behavior under different encounter scenarios. The case study shows that the model can precisely mine collision avoidance information, laying a solid foundation for future research on autonomous collision avoidance decision making for intelligent ships.

Time/frequency technology provides a reliable aircraft collision avoidance system (CAS) that can operate in either synchronous or asynchronous modes. Precision time-ordered techniques of CAS provide both range and range-rate measurements in a one-way sense to all aircraft as well as ground stations within range of transmitted microwave signals. The cooperative system utilizes exact frequency references coupled with precise synchronization: control of frequency to 1 part in 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">8</sup> and time to less than 1 µs. In addition to performing specific functions of protecting aircraft, the time/frequency CAS provides a means for wide dissemination of submicrosecond timing. Flying clocks, which are an integral part of the airborne CAS, have been providing transcontinental and intercontinental transfer of time since 1964. CAS ground stations can serve as depositories of time and frequency derived from flying clocks, satellites, Loran-C and Omega navigation systems, or television transfer referenced to national and international time/frequency standards. Airborne relay of CAS time provides a ready means for local transfer of time to users that are not within line of sight to a ground station. Thus time and frequency can be disseminated for applications other than collision avoidance. In the process of developing the technology and originating CAS, new systems for communication, position determination, navigation, and vehicle surveillance evolved. Such systems can be structured to operate at high data rates, provide improved accuracy and use less RF spectrum than existing techniques.

Numerous researches have been done to develop ASV (Autonomous Surface Vessel) collision avoidance systems. Most of the systems used static methods but did not apply a knowledge base where solutions can be reused and adapted to solve a new case. In this paper, an algorithm of autonomous collision avoidance is proposed considering steering dynamic for ASV. The process of this learning method is to recall the FCBR (Fuzzy Case Base Reasoning) containing basic expert knowledge in the form of stored cases. The solutions will be retrieved from the knowledge base to find a NH (New Heading) command for collision avoidance. Moreover, to execute the NH, a design of adaptive fuzzy ASV heading control system based on command filter is conducted considering the input saturation constraints and external disturbances. T-S fuzzy logic is employed to approximate nonlinear uncertainties existing in the heading control system adopting the MLP (Minimal Learning Parameter) technique. Finally, simulations prove that the method is effective to retrieve the past similar cases for the new collision avoidance situation and give its solution for ASV to track adjusted heading.

In order to effectively deal with collisions in various encounter situations in open water environments, a ship collision avoidance model was established, and multiple constraints were introduced into the velocity obstacle method, a method to determine the ship domain by calculating the safe distance of approach was proposed. At the same time, the ship collision avoidance model based on the ship domain is analyzed, and the relative velocity set of the collision cone is obtained by solving the common tangent line within the ellipse. The timing of starting collision avoidance is determined by calculating the ship collision risk, and a method for ending collision avoidance is proposed. Finally, by comparing the simulation experiments of the improved algorithm with those of the traditional algorithm and the actual ship experiment results of manual ship maneuvering, it is shown that the method can effectively avoid collisions based on safe encounter distances that comply with navigation experience in different encounter situations. At the same time, it has better performance in collision avoidance behavior. It has certain feasibility and practical applicability.

&lt;div class="htmlview paragraph"&gt;Since 1955 the aviation community has been investigating the feasibility of an airborne collision avoidance system. These studies have included analytical and engineering design efforts as well as flight simulation tests and actual flight tests. The majority of the effort expended during these investigations has been devoted to the engineering aspects of the systems. Of equal importance in meeting the overall objective of collision avoidance is the transmission of system information to the crew in a form that can be used effectively in the operational environment. The Boeing Commercial Airplane Company fulfilled a contract for the FAA, using simulation to help determine flight deck display requirements and operational procedures for the traffic alert and collision avoidance system (TCAS II) in commercial transport aircraft.&lt;/div&gt; &lt;div class="htmlview paragraph"&gt;Using the experience gained from these studies, this paper describes the type of efforts required to develop pilot factor characteristics for future collision avoidance systems it addresses man-machine interface requirements to ensure that the system is compatible with the overall aircraft system. It presents some of the functional requirements that the display and control components of the system must meet to accomplish separation assurance. Some of the subjects that are discussed include: a) the impact of the collision avoidance system utilization philosophy on the display requirements; b) the importance of designing the collision avoidance display system so that it can be integrated into the flight deck environment; c) techniques for incorporating realistic human performance estimates into the system performance assumptions; d) the effect on system performance of using natural response patterns; e) techniques that can be used to generate pilot response time commensurate with the situational requirements; f) the role of simulation in the design process; and g) consideration for certification during the development of a collision avoidance system.&lt;/div&gt;

Collision Avoidance Systems (CASs) are attracting a lot of attention as one of the most preferred solutions for advanced driver assistance and autonomous driving. However, scene understanding, which is an essential functionality in CASs, remains a major challenge mainly due to the need for real-time understanding of highly dynamic and complex environment. In this research, a number of robust and low complexity vision based scene understanding techniques for collision avoidance on roadway have been proposed. It has been well recognized in the literature that road surface detection in a dynamic environment is both challenging and computationally intensive. An efficient non-parametric road surface detection algorithm that exploits the depth cue is proposed to overcome the limitations of existing road surface detection methods. Unlike existing methods that attempt to fit the road surface into rigid models, the proposed method results in low computational complexity, mainly due to the reliance on four intrinsic road scene attributes observed under stereo geometry. It has been demonstrated that the proposed method is capable of detecting both planar and non-planar road surfaces. Extensive experimental results using three challenging benchmarks (i.e. enpeda, KITTI stereo/flow, and Daimler) show that the proposed road surface detection algorithm outperforms the baseline algorithms both in terms of detection accuracy (up to 23.12%) and runtime performance (up to 95.00%). Next, robust and low complexity algorithm for computing the ego-vehicle’s motion state is proposed. The proposed method estimates the ego-motion of the vehicle by first employing a novel pruning technique to reduce the computational complexity of the corner feature detection process without compromising on the quality of the extracted corner features. A robust and compute-efficient KLT tracker is proposed to facilitate the generation of the feature correspondences. Finally, an early RANSAC termination condition is introduced to the Gaussian-Newton optimization scheme to achieve rapid convergence of the motion estimation process. Evaluations based on the KITTI odometry benchmark show that the proposed visual odometry method outperforms the baseline algorithms both in terms of accuracy (up to 48.36%) and runtime performance. In addition, the proposed algorithm is placed among the top 15% when evaluated using the well-known KITTI odometry platform. Methods for robust and low complexity stereo-vision based obstacle detection and tracking are proposed. Unlike the works that focus only on the detection of vehicles or pedestrians, the proposed obstacle detection method relies on u-v disparity space to detect all obstacles in the scene. A Space of Interest (SOI) is defined to greatly reduce the search space of obstacles prior to employing adaptive hysteresis thresholding and connected component labeling techniques to segment SOI into sets of obstacles. Method for tracking obstacles across frames is also proposed by constructing a distinctive object appearance model. A number of strategies to further increase the distinctiveness and reduce the computational complexity for constructing the object model are also adopted. Finally, an online multi-object tracking framework is proposed by integrating the obstacle detection and data association modules in a robust way. Evaluations using the KITTI tracking benchmark confirm that the proposed obstacle detection and tracking method outperforms the baseline algorithm in terms of tracking accuracy by up to 51.78%. In addition, compared to the baseline algorithm that achieves about 0.23 frame per second (fps), the proposed method lends well for real-time performance with 20 fps. Finally, an efficient and robust risk assessment framework is proposed by integrating the obstacle detection and tracking, and visual odometry methods proposed in this thesis. The Extended Kalman Filter is customized to enhance the robustness of the predicted trajectory of the obstacles for assessing the collision risk. The robustness of collision prediction has been enhanced by accommodating positioning uncertainty. Evaluations based on the KITTI tracking dataset demonstrate that the proposed method are capable of robust and efficient assessment of the collision risk in diverse traffic scenarios. The proposed vision based scene understanding techniques in this research have paved the way towards realizing a real-time capable collision avoidance system that is both affordable and dependable.

Both ground-based ATC (Air Traffic Control) and airborne CAS (Collision Avoidance Systems) are needed now and in the future to cope with the problem of collision aloft. They should be considered mutually complementary. The limited form of the CAS known as a PWI (Proximity Warning Indicator) is believed not to be sufficient for safety. The two essential elements of a CAS are 1) an indication of the effective maneuver to secure adequate miss distance, and 2) effective means for discovering and assessing the original risk. Miss distance produced by a maneuver never exceeds maneuver displacement. The ratio of the two may be low unless escape time is of the order of 30 seconds or more. In nearly all cases increasing escape time is more effective to insure adequate miss distance than is increasing maneuver severity. The preferred form of CAS would be self-sufficient, but this form appears not to be feasible for basic physical reasons. Cooperative CAS presents many problems, but is believed to have sufficient promise of success to justify careful study and substantial development effort.

Changes of drivers’ visual performances when approaching a signalized intersection under different collision avoidance warning conditions

This work tackles the problem of integrating a pursuit-evasion game (PEG) in a recursive nested behavioral control (RNBC) structure for unmanned aerial vehicles (UAV). The UAV agents’ architecture is the RNBC structure, considering that the collision avoidance, velocity control and attitude control are already implemented behaviors in this structure. The new high-level behaviors pursuit and evasion are introduced, describing the PEG and providing an appropriate reference velocity vector for the underlying layers of the RNBC structure of the pursuer and the evader, respectively. The reference velocities for the agents are determined by solving the pursuit-evasion problem in a game-theoretical manner, while collision avoidance behavior is implemented one level below. The repulsion force approach is used as collision avoidance technique and provides a velocity vector, which is added to the reference velocity vector of the upper level, if there is a collision risk. The resulting reference input is processed by the subjacent layers in the RNBC structure of the UAV. In simulations it is shown that this approach provides a collision-free pursuit-evasion between UAV agents with dynamic constraints in a general three-dimensional environment with previously unknown obstacles.

The effectiveness of auditory forward collision warning alerts

A collision-avoidance (CA) algorithm is developed and implemented that is applicable to many different unmanned aerial systems (UAS), ranging from a single platform with the ability to perform all collision-avoidance functions independently to multiple vehicles performing functions as a cooperative group with collision-avoidance commands computed at a ground station. The algorithm leverages advances in several theoretical fields, including robotics, homing guidance, and airspace management, and considers several approaches to conflict detection and resolution, including the collision cone approach. The collision-avoidance system is exercised and tested by using operational hardware and platforms. Novel developments by using an aggregated collision cone approach allow each unmanned aircraft to detect and avoid collisions with two or more other aircraft simultaneously. The collision-avoidance system is implemented by using a miniature unmanned aircraft with an onboard autopilot. Various simulation and flight test cases are used to demonstrate the algorithm’s robustness to different collision encounters at various engagement angles. The flight test results are compared with ideal, software-in-the-loop, and hardware-in-the-loop tests. The results presented are the first known flight tests of two or more unmanned aircraft systems equipped with the same global, three-dimensional, geometric collision-avoidance system.

Licensed Captains of 80,000 DWT oil tankers were tested on a real time computerized simulator in order to evaluate their collision avoidance behavior in the open sea. Visibility, Traffic density, Navigational aid, and Type of information displayed were manipulated experimentally in order to assess the effects of these variables upon the human's performance in potential collision situations. The findings indicated that a computerized collision avoidance system greatly reduced the danger of collision in poor visibility and in high traffic density whereas the possibility of collision was increased using radar in poor visibility and high traffic density. Furthermore, it was found that a meaningful graphic display of information was responsible for the improved performance as compared to a visual alphanumeric display of target ship information.