Robust model predictive control for robotic manipulators with fully actuated system approach based on learning modelling

Constant-air-volume (CAV) air-conditioning systems consist mainly of two local processes: an air-handling process and a room temperature process. A robust model predictive control (RMPC) strategy was developed for CAV air-conditioning systems, which adopted two uncertain first-order plus time-delay models to describe the dynamics of the local processes and used a linear matrix inequality (LMI)-based optimisation technique to optimise the control law. This paper develops a new control design, which reformulates the prediction models by shifting the uncertainties of the first model into the second one, and then uses the reformulated prediction models in the RMPC strategy. This paper will show that compared with the original design, the new control design can enhance the feasibility of the optimisation of control law, reduce the computational burden of the optimisation and also remove the requirement of a sensor for supply air temperature in the original design. Practical applications: The new design method is a further development of a RMPC strategy presented in Xu et al.13 It inherits the benefits of the original control design for practical application, i.e. uncertainties and constraints can be dealt with simultaneously in the design and the robustness of the controlled system can be enhanced. The new design improves the optimisation feasibility, reduces the computational complexity and does not need to measure the supply air temperature. When the new design is adopted to replace the traditional PI control, there is no necessity to change the existent input structure of the PI control. Hence, the new design can be realised in practice easier than the original design.

To improve the accuracy of tracking unmanned vehicles on known trajectories, two optimised model predictive control (MPC) trajectory tracking control systems are designed based on the adaptive compensation and robust control of a radial basis function (RBF) neural network. Based on the traditional MPC trajectory tracking controller and the local approximation characteristics of the RBF neural network, the proposed RBF compensation–MPC control system is designed to compensate for the inaccuracy in the MPC prediction model arising from modelling errors. The results show that this method can achieve a root mean square error of less than 0.3703 m for the lateral position. Subsequently, to suppress the error generated by the RBF neural network and reduce the degree of vehicle sideslip, the error is considered to be external interference, and the anti-interference characteristic of the RBF robust control is incorporated into the RBF robust-MPC control system. Following the re-optimisation of the RBF robust control, the root mean square error of the lateral position is set within 0.2352 m. The results of a MATLAB/Carsim joint simulation show that using the RBF robust control can improve the tracking accuracy of the traditional MPC controller compared with RBF compensation control, while simultaneously improving the driving stability of the vehicle.

This paper presents a method to design a predictive controller for a single Inverted Pendulum (SIP) system. The design goal is to balance the pendulum in the inverted position in the presence of parameter variations and measurement white noise Using linearization technique, the model of SIP system is transformed to a linear polytopic system. Since we need to estimation of states, a new robust model predictive control (RMPC) strategy is developed for this system with considering white measurement noise. Simulation results are presented to show the robustness of the closed-loop system against parameter variations and measurement white noise.

This paper presents a method to design a predictive controller for a Rotational Inverted Pendulum (RIP) system. The design goal is to balance the pendulum in the inverted position. After linearization, the model of RIP system is transformed to a linear polytopic system with bounded disturbances and a new robust model predictive control (RMPC) strategy is developed for this system. Simulation results are presented to show the robustness of the closed-loop system against parameter variations and disturbances. The proposed method can be considered as a promising way for control of various similar nonlinear systems.

A novel robust model predictive control strategy is presented for a class of discrete-time time-varying system with delays. The modified quadratic Lyapunov-Krasovskii functionals for uncertain discrete-time system with both states and input delays is proposed. A robust model predictive control law is derived such that the closed-loop system is asymptotically stable and a dasiaworst-casepsila infinite horizon performance objective is minimized. A feasible state feedback model predictive control law is obtained by using linear matrix inequalities approach. And then, a convex optimization problem is formulated to design the robust model predictive controller which minimizes the upper bound of the closed-loop performance objective. The robust model predictive controller design is illustrated with numerical examples.

ABSTRACTThis article presents a model predictive control (MPC) strategy that leverages neural ordinary differential equations (NODEs) to address the persistent issue of model mismatch in nonlinear systems. A residual model based on NODEs is employed to capture the differences between the actual system dynamics and conventional models. Simultaneously, an approximate model with an uncertainty upper bound, derived from first principles, is introduced. These two models are integrated into a learning‐based MPC framework, effectively decoupling system safety and performance, leading to more reliable control. To enhance model and controller adaptability, we propose an online dynamic learning framework that continuously refines the accuracy of the dynamic model. Compared to traditional learning‐based MPC, the proposed algorithm significantly reduces memory usage. Furthermore, using the theory of invariant sets, we establish the recursive feasibility and stability of the algorithm. The method's effectiveness is demonstrated through addressing nonlinear problems involving modeling errors and stochastic disturbances.

In this paper, an integrated tube robust iterative learning model predictive control (Tube‐RILMPC) strategy based on the dynamic partial least squares (DyPLS) identified algorithm is proposed. The problems of large amount of online data calculation and input and output variable dimensions disaster in the original variable space are solved. This integrated Tube‐RILMPC strategy enhances the tracking performance and robustness of two‐dimensional (2D) control system. The output trajectories of system are located in the tube the nominal trajectory, which reduces the modelling error caused by the uncertain model. Based on the worst‐case performance index of ellipsoidal uncertainty and polytopic uncertainty, a robust iterative learning control (ILC) strategy is designed. Finally, the superiority of the proposed control algorithm is verified by comparative simulation.

This paper presents an event-triggered model predictive control (MPC) strategy with learning terminal cost for robotic manipulators containing model uncertainty and input constraints. In the proposed MPC structure, an adaptive predictive model for the robotic system is established by radial basis function neural networks (RBFNNs) firstly. Then, a terminal cost adjusted by the global learning mechanism is constructed. Both global steady-state optimization and transient fast convergence are achieved by adding the learning terminal cost to the MPC scheme. After that, a triggering condition of the MPC solving is developed based on the predictive model’s weights and the predictive tracking error. Besides, the condition to avoid Zeno behavior is obtained. The recursive feasibility of the proposed MPC strategy is verified, and the ultimately uniformly boundedness (UUB) of all variables is proved according to the Lyapunov theorem. Finally, experiments based on an xMate7 Pro robot are conducted to demonstrate the effectiveness of the presented method. Note to Practitioners—The tracking control of robotic manipulators is a common and important problem in industrial applications, such as grasping, loading, unloading, et al. There exist some limitations in existing control methods. For example, general control strategies such as adaptive control, sliding mode control neglect the balance between control costs and expected performance; existing optimal control approaches rarely consider global steady-state optimization and transient fast convergence under the influence of model uncertainty. This paper is motivated by these limitations of robotic control design and inspired by model predictive control and optimal control theory. It develops a novel strategy for tracking control of robotic manipulators, which includes three following items: (1) adopt an approximation model constructed by neural networks as the predictive model for estimating the robotic system; (2) introduce a critic network into the terminal cost of the objective function of MPC for learning global optimal solution; (3) establish an event-triggered mechanism for solving of the optimization problem. The proposed method is verified by experimental results. In our future work, the proposed control strategy will be applied to more industrial processes.

Many robust model predictive control (MPC) schemes require the online solution of a computationally demanding convex program. For deterministic MPC schemes, multiparametric programming was successfully applied to move offline most of the computation. In this paper, we adopt a general approximate multiparametric algorithm recently suggested for convex problems and propose to apply it to a classical robust MPC scheme. This approach enables one to implement a robust MPC controller in real time for systems with polytopic uncertainty, ensuring robust constraint satisfaction and robust convergence to a given bounded set

In this paper we propose a stochastic model predictive control (MPC) formulation based on scenario generation for linear systems affected by discrete multiplicative disturbances. By separating the problems of (1) stochastic performance, and (2) stochastic stabilization and robust constraints fulfillment of the closed-loop system, we aim at obtaining a less conservative control action with respect to classical robust MPC schemes, still enforcing convergence and feasibility properties for the controlled system. Stochastic performance is addressed for very general classes of stochastic disturbance processes, although discretized in the probability space, by adopting ideas from multi-stage stochastic optimization. Stochastic stability and recursive feasibility are enforced through linear matrix inequality (LMI) problems, which are solved off-line; stochastic performance is optimized by an on-line MPC problem which is formulated as a convex quadratically constrained quadratic program (QCQP) and solved in a receding horizon fashion. The performance achieved by the proposed approach is shown in simulation and compared to the one obtained by standard robust and deterministic MPC schemes.

Reconfiguration of flow-based networks with back-up components using robust economic MPC

Energy efficient convex-lifting-based robust control of a heat exchanger

A methodology is proposed to design a robust Gain-Scheduled Model Predictive Control (MPC) strategy and to quantify the relative advantages of this controller versus a Linear MPC strategy. For the purpose of analysis and controller design, the process is represented by a nonlinear state-affine model identified from input−output data. This model can be split in linear and nonlinear terms where the linear part is used for controller design and the nonlinear part is accounted for as model uncertainty. Then, robust stability and robust performance tests are formulated based on linear matrix inequalities where the manipulated variables weight of the controllers is tuned to maximize performance. The uncertainty bounds used for the robustness tests are obtained in an iterative fashion by using the frequency response of the manipulated variable with respect to the feedback error. The control strategy performance is quantified by the ratio between the error norm and the disturbance norm. Finally, a case study involving a multiple-input−multiple-output bioreactor is presented. The study is able to predict for which range of operation the Gain-Scheduling MPC surpasses the performance of the Linear MPC.

Data-Driven Prediction and Predictive Control Methods for Eco-Driving in Production Vehicles

One of the main advantages of predictive control approaches is the capability of dealing explicitly with constraints on the manipulated and output variables. However, if the predictive control formulation does not consider model uncertainties, then the constraint satisfaction may be compromised. A solution for this inconvenience is to use robust model predictive control (RMPC) strategies based on linear matrix inequalities (LMIs). However, LMI-based RMPC formulations typically consider only symmetric constraints. This paper proposes a method based on pseudoreferences to treat asymmetric output constraints in integrating SISO systems. Such technique guarantees robust constraint satisfaction and convergence of the state to the desired equilibrium point. A case study using numerical simulation indicates that satisfactory results can be achieved.