Robust orbital-angular-momentum-based underwater acoustic communication with dynamic modal decomposition method.

Traditional wireless links employing OAM (orbital angular momentum) beams make use of their spatial orthogonality in order to increase their spectral efficiency, by carrying a separate data stream on each beam. This requires that the OAM antenna axes are aligned with the line of sight of the link, and are capable of radiating and receiving high-purity orthogonal OAM beams. Due to the deep spatial nulls of these beams (except the zero-order OAM beam) on their axes, the received signal strengths are much lower than from conventional beams of comparable-sized antennas, limiting the signal-to-noise ratio (SNR) and the reach of such links, or requiring very large receive antennas in terms of wavelengths.Here we describe an alternative technique for recovering received OAM beams based on pseudo-Doppler techniques [1]-[3] which avoid the above limitations of traditional OAM links. In this work, the receiving antennas are not aligned with the OAM beam axes, so the received signals are stronger, the receivers and their antennas are fewer and simpler, and the reach is longer than in traditional wireless OAM links. We demonstrate for the first time, by simulations and experiments performed on an outdoor 100m link at 28 GHz, that it is possible to recover 4 independent data streams carried in a common 20MHz channel on 4 co-aperture OAM beams using the technique developed in [1], with only 2 receiver chains. The transmitting OAM antenna radiates all OAM beams with the same cone angles and the 2 receiving antennas are set on their peaks off-axis in the far field, 20cm apart and tangent to the OAM cones, unlike in traditional OAM wireless links [4]. Salient aspects of the pseudo-Doppler OAM recovery algorithm, its simulation in an end-to-end link, and key design features of the demonstration hardware and signal-processing are presented.

As a pathbreaking approach to generate orbital angular momentum (OAM) beam, uniform circular array (UCA) has been extensively researched and applied. However, the impact of the imperfect UCA (IUCA) converted from a UCA with the position of antenna elements on the purity of the generated OAM beam is rarely considered. In order to verify the effect of position deviation on the OAM beam, this letter deduces the analysis model of the IUCA and the OAM mode purity model. The OAM mode purity refers to the weight of the intensity of the "expected OAM mode." Numerical simulation results show that the OAM beam generated by IUCA is a superposition of OAM beams with a series of different modes, and this results in a certain OAM beam received being contaminated. Compared with the radius deviation, the azimuth deviation of antenna elements has more obvious influence on the OAM mode purity. Moreover, low-mode OAM beams are more suitable for long-distance transmission. Properly increasing the antenna array radius can improve the purity of high-order OAM modes.

Vector orbital angular momentum (OAM) beams, described by higher-order Poincaré (HOP) sphere, are generalized forms of waves carrying OAM with an inhomogeneous polarization of wavefronts. We construct all-dielectric metasurfaces with adjustable amplitude, polarization, and phase to generate arbitrary vector OAM beams. The metasurface is composed of two pairs of silicon nanopillars arranged alternately. Using the interference effect of the four meta-atoms related to the circular polarization, combined with the propagation and geometric phases, two OAM beams with controlled amplitude, phase, and equal topological charge but opposite signs can be obtained under the incidence of orthogonally circularly polarized lights. For the x linearly polarized light, arbitrary vector OAM beams on the HOP sphere are generated via the superposition of the above OAM beams. Additionally, the evolution process of the beam on the longitude and latitude of the Poincaré sphere is revealed by changing the amplitude and phase of the two OAM beams. This work provides a simple, effective, and flexible method for realizing vector OAM beams while having potential implications for the generation and manipulation of vectorial light fields at the micro-nano scale.

Orbital angular momentum (OAM) beams have attracted great attention owing to their excellent performances in imaging and communication. In this paper, a dual-arm Archimedean spiral antenna (DASA) is proposed to generate multiple OAM states with positive and negative values by feeding at the inner and outer ends, respectively. The topological charge of radiated vortex waves is reconfigurable by tuning the operating frequency. Dual-mode OAM states are generated at different working frequencies (l = ±1 at 3 GHz, l = ±2 at 4 GHz, and l = ±3 at 4.8 GHz). Both the simulation and measurement results demonstrate that OAM beams can be generated effectively by the DASA. In addition, a conical cavity is used to increase the gain of the proposed DASA for more than 5 dBi in comparison to the traditional cylindrical cavity. Furthermore, the qualities of the generated OAM modes by the proposed DASA have been evaluated at different operating frequencies of 3 GHz, 4 GHz, and 4.8 GHz, respectively. The OAM modes purities of l = −1, −2, −3, 1, 2, and 3 are predominate with the proportion of about 81%, 70%, 74%, 78%, 77%, and 75%, respectively. Our results demonstrate that the proposed DASA has great potentials in OAM multiplexing communication systems.

We experimentally demonstrate turbulence-resilient free-space optical (FSO) coherent communications with multiple multiplexed data channels in different orthogonal domains, including mode, polarization, and wavelength. The turbulence resiliency is enabled by utilizing pilot-assisted optoelectronic mixing of the received beams, wherein one pilot is being mixed with its corresponding beam. By transmitting additional continuous-wave (CW) pilot tones, whose frequencies are offset from the data-carrying beams, and mixing all pilot tones and beams in a single free-space-coupled photodetector (PD) at the receiver, the turbulence-induced modal coupling could be efficiently suppressed. The paper first discusses an experimental demonstration of a turbulence-resilient mode-division-multiplexed (MDM) FSO communication link using two orbital angular momentum (OAM) beams. Each OAM beam carries an independent 2-Gbit/s quadrature-phase-shift-keying (QPSK) data channel. Experimental results indicate that (i) the channel crosstalk under both the weaker and stronger turbulence distortions are measured to be lower than ∼−25.7 dB, (ii) the turbulence-induced OAM modal coupling could be effectively suppressed for the emulated 15 random turbulence realizations, and (iii) the error-vector magnitudes (EVM) of the multiplexed QPSK data channels are measured to be lower than by 17.4% and 19.8% under the relatively weaker and stronger turbulence effects, respectively. The paper subsequently describes an experimental demonstration of a turbulence-resilient FSO link with eight 0.5-Gbit/s QPSK data channels multiplexing two OAM beams ( <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">l</i> = +1 & <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">l</i> = −2), two polarizations, and two wavelengths. The measured bit-error rates (BERs) of all data channels under turbulence effects are below the 7% forward-error-correction (FEC) limit, with power penalties less than ∼3.7 dB.

As the dominant information carrier in water, the acoustic wave is widely used for underwater detection, communication and imaging. Even though underwater acoustic communication has been greatly improved in the past decades, it still suffers from slow transmission speeds and low information capacity. The recently developed acoustic orbital angular momentum (OAM) multiplexing communication promises a high efficiency, large capacity and fast transmission speed for acoustic communication. However, the current works on OAM multiplexing communication mainly appear in airborne acoustics. The application of acoustic OAM for underwater communication remains to be further explored and studied. In this paper, an impedance matching pentamode demultiplexing metasurface is designed to realize multiplexing and demultiplexing in underwater acoustic communication. The impedance matching of the metasurface ensures high transmission of the transmitted information. The information encoded into two different OAM beams as two independent channels is numerically demonstrated by realizing real-time picture transfer. The simulation shows the effectiveness of the system for underwater acoustic multiplexing communication. This work paves the way for experimental demonstration and practical application of OAM multiplexing for underwater acoustic communication.

The Orbital Angular Momentum (OAM) carried by light beams with helical phasefront (vortex beams) has been widely employed in many applications such as optical tweezers, optical drives of micro-machines, atom trapping, and optical communication. OAM provides an additional dimension (diversity) to multiplexing techniques, which can be utilized in addition to conventional multiplexing methods to achieve higher data rates in wireless communication. OAM beams have been thoroughly studied and used in the optical regime but in the mm-wave and THz-wave region, they are still under investigation. In these frequency bands, there are difficulties associated with beam-splitting and beam-combining processes as well as with the use of spiral phase plates and other methods for OAM generation, since the wavelength is much larger compared to those at optical frequencies, leading to higher diffraction losses. The present paper describes the natural generation of high-power OAM modes by gyro-type vacuum electron devices with cylindrical interaction circuit and axial output of the generated rotating higher-order transverse electric mode TEm,n, where m &gt; 1 and n are the azimuthal and radial mode index, respectively. The ratio between the total angular momentum (TAM) JN and total energy WN of N photons is given by m/ω, where ω is the angular frequency of the operating mode, which in a gyrotron oscillator is close to the TEm,n-mode cutoff frequency in the cavity. Therefore, m/ω = Rc/c, where Rc is the caustic radius and c the velocity of light in vacuum. This means that the OAM is proportional to the caustic radius and at a given frequency the same for all modes with the same azimuthal index m. Right-hand rotation (co-rotation with the electrons) corresponds to a positive value of m and left-hand rotation to negative m. The corresponding OAM mode number (topological charge) is l = m – 1. Circularly polarized TE1n modes only possess a Spin Angular Momentum (SAM: s = ±1). TE0n modes have neither SAM nor OAM. This is the result of the photonic (quasi-optical) approach to derive the TAM of modes generated in gyrotrons. The same result follows from the electromagnetic (EM) wave approach for the TAM within a given waveguide volume per total energy of the EM wave in the same volume. Such high-power output beams with very pure higher-order OAM, generated by gyrotron oscillators or amplifiers (broadband) could be used for multiplexing in long-range wireless communications. The corresponding mode and helical wavefront sensitive detectors for selective OAM-mode sorting are available and described in the present paper.

Long-range acoustic communication is crucial to underwater applications such as collection of scientific data from benthic stations, ocean geology, and remote control of off-shore industrial activities. However, the transmission rate of acoustic communication is always limited by the narrow-frequency bandwidth of the acoustic waves because of the large attenuation for high-frequency sound in water. Here, we demonstrate a high-throughput communication approach using the orbital angular momentum (OAM) of acoustic vortex beams with one order enhancement of the data transmission rate at a single frequency. The topological charges of OAM provide intrinsically orthogonal channels, offering a unique ability to multiplex data transmission within a single acoustic beam generated by a transducer array, drastically increasing the information channels and capacity of acoustic communication. A high spectral efficiency of 8.0 ± 0.4 (bit/s)/Hz in acoustic communication has been achieved using topological charges between -4 and +4 without applying other communication modulation techniques. Such OAM is a completely independent degree of freedom which can be readily integrated with other state-of-the-art communication modulation techniques like quadrature amplitude modulation (QAM) and phase-shift keying (PSK). Information multiplexing through OAM opens a dimension for acoustic communication, providing a data transmission rate that is critical for underwater applications.

Artificial intelligence methods for the phase control of laser arrays have been extensively developed in the recent years. To tailor high-power and fast switchable orbital angular momentum (OAM) beams by the coherent combination of laser arrays, complex phase control difficulties arise, and the introduction of deep-learning (DL) methods to learn the mapping from the intensity information to the relative phases of array elements offers a promising solution. In this work, we theoretically propose a DL-based phase control scheme that can customize OAM beams with desirable topological charges from laser array systems, which relies on the acquisition of the optical field information in the view of angular domain. When the system in closed loops, the optical field and phase errors information of laser array are extracted and decoupled in the angular domain perspective by using an OAM demultiplexer. The processed optical field of the coherently combined beam serves the DL-based phase control servo to realize the efficient phase stabilization, thus ensuring the controllable customization of OAM beams. This work could provide a useful reference on the intelligent control of laser array systems for structured light beams customization.

Orbital angular momentum (OAM) beams allow for increased channel capacity in free-space optical communication. Conventionally, these OAM beams are multiplexed together at a transmitter and then propagated through the atmosphere to a receiver where, due to their orthogonality properties, they are demultiplexed. We propose a technique to demultiplex these OAM-carrying beams by capturing an image of the unique multiplexing intensity pattern and training a convolutional neural network (CNN) as a classifier. This CNN-based demultiplexing method allows for simplicity of operation as alignment is unnecessary, orthogonality constraints are loosened, and costly optical hardware is not required. We test our CNN-based technique against a traditional demultiplexing method, conjugate mode sorting, with various OAM mode sets and levels of simulated atmospheric turbulence in a laboratory setting. Furthermore, we examine our CNN-based technique with respect to added sensor noise, number of photon detections, number of pixels, unknown levels of turbulence, and training set size. Results show that the CNN-based demultiplexing method is able to demultiplex combinatorially multiplexed OAM modes from a fixed set with >99% accuracy for high levels of turbulence-well exceeding the conjugate mode demultiplexing method. We also show that this new method is robust to added sensor noise, number of photon detections, number of pixels, unknown levels of turbulence, and training set size.

Orbital angular momentum (OAM) light, combined with the nonlinear process to expand the frequency range, has drawn increasing research interest in recent years. Here, we implement the first, to the best of our knowledge, experimental fourth-harmonic generation of OAM light with two cascaded quasi-phase-matching crystals. A Laguerre-Gaussian beam was transmitted through a duplet crystals system and frequency-doubled twice by two separate second-harmonic generation processes, which transduced the frequency of the OAM beam from telecom band to visible band and then to ultraviolet (UV) band. The topological charge of the OAM beam was increased substantially in the cascaded frequency conversion processes. In this experiment, we verify the OAM conservation by utilizing a specially designed interferometer, and the results correspond well with the numerical simulation. This work provides an effective method for the generation of UV OAM beams with high topological charges.

We propose a new, three-parameter family of diffraction-free asymmetric elegant Bessel modes (aB-modes) with an integer and fractional orbital angular momentum (OAM). The aB-modes are described by the nth-order Bessel function of the first kind with complex argument. The asymmetry degree of the nonparaxial aB-mode is shown to depend on a real parameter c≥0: when c=0, the aB-mode is identical to a conventional radially symmetric Bessel mode; with increasing c, the aB-mode starts to acquire a crescent form, getting stretched along the vertical axis and shifted along the horizontal axis for c≫1. On the horizontal axis, the aB-modes have a denumerable number of isolated intensity zeros that generate optical vortices with a unit topological charge of opposite sign on opposite sides of 0. At different values of the parameter c, the intensity zeros change their location on the horizontal axis, thus changing the beam's OAM. An isolated intensity zero on the optical axis generates an optical vortex with topological charge n. The OAM per photon of an aB-mode depends near-linearly on c, being equal to ℏ(n+cI1(2c)/I0(2c)), where ℏ is the Planck constant and In(x) is a modified Bessel function.

In this paper, a design of circular single-sideband (SSB) time-modulated array (TMA) for generating orbital angular momentum (OAM) beams is proposed. It increases signal bandwidth significantly compared with conventional TMAs for generating vortex waves. Theoretical analysis and simulated results of the proposed SSB TMA modulated by the optimized four-step pulse are reported. Higher harmonic efficiency and total efficiency (98.73% and 64.15%) are achieved simultaneously. And mode 1, 2, and 3 OAM beams with mode purity up to 97.3%, 97.2%, and 79.6% are generated at the first positive harmonic frequency.

Structured light carrying orbital angular momentum (OAM) opens up a new physical dimension for studying light–matter interactions. Despite this, the complex fields created by OAM beams still remain largely unexplored in terms of their effects on surface plasmons. This paper presents a revelation of anomalous plasmon excitations in single particles and plasmon couplings of neighboring nanorods under OAM beams, which are forbidden using non-OAM sources. The plasmon excitation of single nanoparticles is determined both by photon spin angular momentum (SAM) and OAM and influenced by the locations of the nanoparticles. Specifically, when SAM and OAM are equal in magnitude and opposite in direction, a pure plasmon excitation along light propagation direction is achieved. Two plasmon dipoles show end-to-end antibonding coupling and side-by-side bounding coupling, which are the opposite of the typical couplings. Furthermore, we observe Fano resonance with a nanorod dimer: one aligned along light propagation direction acting as the bright mode and the other aligned along the global polarization direction of light acting as the dark mode, which is the opposite of the usual plasmonic Fano resonance. By taking advantage of the unique property of the OAM source, this investigation presents a novel way to control and study surface plasmons, and the research of plasmon behavior with OAM would open new avenues for controlling electromagnetic waves and enriching the spectroscopies with more degrees of freedom.

Free-space optical (FSO) communication holds significant potential for future systems due to its high bandwidth and installation-free advantages. However, FSO faces critical challenges including atmospheric turbulence and security vulnerabilities such as susceptibility to interception. To address these issues, this paper proposes a multi-parameter encrypted FSO communication scheme based on generalized polygonal non diffractive vortex beams (GPNBs). By incorporating multiple structural dimensions with edge count factor, smoothness factor, and topological charge. The system achieves multidimensional information modulation and enhanced encryption capabilities. While a MobileNetV3-Small-based neural network decoder enables high-precision demodulation. Experimental results demonstrate successful transmission of three color images over 1 meter with a bit error rate (BER) of 3.9×10<sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−3</sup> using combinations of 8 orbital angular momentum (OAM) modes, 3 smoothness factors, and 3 edge number factors. The non-diffractive characteristics maintain BER at 5×10<sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">−2</sup> under moderate to high atmospheric turbulence, while the beam's self-healing properties enable recovery from obstructions within 1 meter. This multidimensional encryption mechanism and lightweight neural network decoding strategy provide a promising solution for high-capacity, secure, and robust FSO communication in complex environments.