Route Planning and Tracking Control of an Intelligent Automatic Unmanned Transportation System Based on Dynamic Nonlinear Model Predictive Control

In active collision avoidance, the trajectory tracking controller determines the deviation from the reference path and the vehicle stability. The main objective of this study was to reduce the tracking error and improve the tracking performance in collision avoidance. Unlike the previously proposed model predictive control (MPC) strategies with constant sampling time, an improved MPC controller with varying sampling time based on the hierarchical control framework was proposed in this paper. Compared with the original MPC tracking controller, the improved MPC controller demonstrated better adaptive capability for the varying road adhesion coefficients and vehicle speed on a curved road. The simulation results revealed that the hierarchical control framework generated an optimal trajectory for collision avoidance in real-time by minimizing the potential field energy.

Multi-vector model predictive control of permanent magnet synchronous motor can effectively overcome the shortcomings of conventional single-vector model predictive control such as large motor current ripples and limited control accuracy, but its control performance is more susceptible to the influence of motor parameter perturbation. To improve the robustness of the multi-vector predictive control algorithm under the motor parameter perturbation, a novel nonparametric three-vector model predictive current control method for permanent magnet synchronous motors is proposed in this paper. Through constructing an ultra-local predictive current model based on the input and output signals of the permanent magnet synchronous motor, the influence of motor parameter perturbation on current prediction is avoided, and a disturbance observer is designed to estimate the non-modeled and perturbed parts of the ultra-local model. In addition, the direct calculation method of vector duty cycles based on current error is introduced to suppress the influence of motor parameter uncertainty on the duty cycle calculation link, which further improves the system robustness. Finally, simulations and experiments of the proposed method are demonstrated to compare with the conventional parametric three-vector model predictive current control, and the results show that the proposed control strategy can effectively suppress the disturbances caused by the motor parameters and ensure the steady-state performance during motor operation.

Model predictive control (MPC) as a nonlinear control method, is being studied for a wide variety of power electronics applications targeting various power ranges. The fast dynamic response, robustness under different load conditions, multi-objective control, and simplicity of implementation are the main features of MPC. However, the implementation of finite control set MPC (FCS-MPC) or direct MPC in its basic form for multilevel converters (MLCs) demonstrates the inability to generate the staircase multilevel output voltage waveform in a voltage sourced inverter (VSI) application. Adding a reference evaluation block to the basic FCS-MPC method can significantly improve its multilevel voltage generation capability. In this paper, an enhanced model predictive nearest level control (EMP-NLC) is proposed and implemented on a 5-Level flying capacitor multilevel converter (FCMC). The proposed method is simulated under different load conditions, while a comparison against existing MPC techniques is also presented. Experimental results verified the efficacy of the proposed controller.

Model predictive control (MPC) presents important advantages in the control of the power converter and drives such as, fast dynamic response and capability to include nonlinear constrains. These have positioned MPC as a powerful and realistic control strategy, however, it also has disadvantages such as variable switching frequency and parameter sensitivity. This paper applied a modulated model predictive speed control that guarantees a fix switching frequency and, thanks to disturbance compensation, robustness to parameters variation. The strategy is validated and compared to finite set model predictive speed control through simulation results.

This paper deals with the design and the robustness analysis of a model predictive control (MPC) for the position tracking of primary flight movables driven by electro-mechanical actuators. This study is, in particular, focused on a rotary electro-mechanical actuator (EMA) by UMBRAGROUP, employing a patented mechanical transmission based on a differential ball-screw mechanism characterized by a huge gear ratio. To obtain a baseline reference, conventional PID regulators were initially optimized by using multi-objective cost functions based on tracking accuracy, load disturbance rejection, and power consumption. The position regulator was then replaced by an MPC regulator, designed to balance performance, computational resources, and safety constraints. A nonlinear physics-based simulation model of the EMA, entirely developed in the Matlab–Simulink environment and validated with experiments, was used to compare the two control strategies. The simulation results in both the time and frequency domains highlight that the MPC solution provides faster and more accurate position tracking, improved dynamic stiffness, and reduced power absorption. Finally, the robustness against model uncertainties of the MPC was addressed by imposing random and combined deviations of model parameters from the nominal values (via Monte Carlo analysis). The results demonstrate that the implementation of MPC control laws could enhance the stability and the reliability of EMAs, thus supporting their application for safety-critical flight control functions.

This paper presents a viable approach for incorporating collision avoidance strategies into existing guidance and control systems on marine vessels. We propose a method that facilitates the use of simulation-based Model Predictive Control (MPC) for collision avoidance (COLAV) on marine vessels. Any COLAV strategy to be applied in real traffic must adhere to the international regulations for preventing collisions at sea (COLREGS). The proposed MPC COLAV method does not rely on an accurate model of the guidance system to achieve vessel behaviors that are compliant with the COLREGS. Rather, it depends on transitional costs in the MPC objective for collision avoidance maneuvers that are being executed by the marine vessel. Hence, it is straightforward to implement the MPC COLAV on different vessels without specific knowledge of the vessel's guidance strategy. Moreover, it offers the possibility to switch between different (possibly application specific) guidance strategies on the same vessel while running the same MPC COLAV algorithm. We present results from full scale experiments that show the viability of our method in different collision avoidance scenarios.

This paper presents a distributed solution for the problem of collaborative collision avoidance for autonomous inland waterway ships. A two-layer collision avoidance framework that considers inland waterway traffic regulations is proposed to increase navigational safety for autonomous ships. Our approach allows for modifying traffic rules without changing the collision avoidance algorithm, and is based on a novel formulation of model predictive control (MPC) for collision avoidance of ships. This MPC formulation is designed for inland waterway traffic and can handle complex scenarios. The alternating direction method of multipliers is used as a scheme for exchanging and negotiating intentions among ships. Simulation results show that the proposed algorithm can comply with traffic rules. Furthermore, the proposed algorithm can safely deviate from traffic rules when necessary to increase efficiency in complex scenarios.

Fifty-seven per cent of all water supply systems in the Netherlands are controlled by model predictive flow control; the other 43% are controlled by conventional level-based flow control. The differences between conventional level-based flow control and model predictive control were investigated in experiments at five full-scale water supply systems in the first half of 2011. Quality parameters of the drinking water and energy consumption of the treatment and distribution processes were measured and analysed. The experiments showed that the turbidity values are 12–28% lower, and particle volume values 12–42% lower for the systems which are controlled by model predictive flow control. The overall energy consumption of water supply systems controlled by predictive flow control is 1.0–5.3% lower than conventional level-based flow controlled systems, and the overall energy costs are 1.7–7.4% lower.

The need for cost-effective fuel economy improvements has driven the introduction of automatic transmissions with an increasing number of gear ratios. Incorporation of interlocking dog clutches in these transmissions decreases package space and increases efficiency, as compared to conventional dry or wet clutches. Unlike friction based clutches, interlocking dog clutches require very precise rotational speed matching prior to engagement. Precise engine speed control is therefore critical to maintaining high shift quality. This research focuses on controlling the engine speed during a gearshift period by manipulating throttle position and combustion phasing. Model predictive control (MPC) is advantageous in this application since the speed profile of a future prediction horizon is known with relatively high confidence. The MPC can find the optimal control actions to achieve the designated speed target without invoking unnecessary actuator manipulation and violating hardware and combustion constraints. This research utilizes linear parameter varying (LPV) MPC to control the engine speed during the gearshift period. Combustion stability constraints are considered with a control oriented covariance of indicated mean effective pressure model (COV of IMEP). The proposed MPC engine speed controller is validated with a high-fidelity 0-dimensional engine model with crank angle resolution. Four case studies, based on simulation, investigate the impact of different MPC design parameters. They also demonstrate that the proposed MPC engine controller successfully achieves the speed reference tracking objective while considering combustion variation constraints.

Model predictive control (MPC) is an efficient and growing approach to power converter control. This paper proposes an improved and simplified model predictive current control (MPCC) technique for a four-level nested neutral point clamped (4L-NNPC) converter. Conventional MPCC exhibits better performances as compared to the conventional linear control system such as fast dynamic response, consideration of the system constraints, and nonlinearities. However, the application of the conventional model predictive current control (MPCC) approach on complex systems provokes a significant number of calculations, which is the main hurdle to its practical implementation. To fix this flaw, this paper proposes an effective algorithm to shorten the execution time of the conventional MPCC. In this proposed technique, 216 current predictions of the conventional MPCC are skipped and converted into one required voltage vector (RVV) prediction. With this equivalent reference voltage transformation, the calculation burden of MPCC is significantly reduced, while the output performance is not influenced. The results of the simplified MPCC for the 4L-NNPC converter are analyzed and compared with the conventional MPCC. The computational time is reduced by 19.56% using the simplified MPCC, while keeping an approximately similar error of output currents. The switching frequency and total harmonic distortion (THD) of the proposed method are reduced by 8.16% and 0.07%, respectively, as compared to the conventional technique. These results demonstrate the fact that that the performance of a conventional MPCC is enhanced with the proposed MPCC. The proposed algorithm can be applied to several inverter topologies.

Nowadays, a model predictive control has gained a lot of attractions for power converter. To overcome the defects of the conventional model predictive control and achieve better performance, this article presents a multivector model predictive power control (MV-MPPC) with low computational burden for the grid-tied quasi-Z-source inverter (qZSI). Compared with the conventional model predictive power control (MPPC) that adopts only one vector in one control period, the proposed MV-MPPC applies several vectors including two active vectors, one null vector, and one shoot-through (ST) vector to fulfill the expected performance for the grid-tied qZSI. By calculating the optimal duty ratios of the ST vector, the inductor current ripple can be greatly reduced. To eliminate the weighting factor, a modified sliding-mode control method for simultaneously controlling the capacitor voltage and the inductor current to their setting points is proposed. Furthermore, a quick and effective optimal sector selection method is given, which chooses the optimal sector through a look-up table instead of a bunch of complex calculations. Hence, the computational burden of the proposed MV-MPPC is decreased with significance. Both simulation and experimental results are shown to validate the effectiveness and the advantages of the proposed method.

The research object of this paper is single-phase PWM rectifier, the purpose is to reduce the total harmonic distortion (THD) of the grid-side current. A model predictive current control (MPCC) with fixed switching frequency and dead-time compensation is proposed. First, a combination of an effective vector and two zero vectors is used to fix the switching frequency, and a current prediction equation based on the effective vector’s optimal action time is derived. The optimal action time is resolved from the cost function. Furthermore, in order to perfect the established prediction model and suppress the current waveform distortion as a consequence of the dead-time effect, the dead-time’s influence on the switching vector’s action time is analyzed, and the current prediction equation is revised. According to the experimental results, the conclusion is that, firstly, compared with finite-control-set model predictive control, proportional-integral-based instantaneous current control (PI-ICC) scheme and model predictive direct power control (MP-DPC), the proposed MPCC has the lowest current THD. In addition, the proposed MPCC has a shorter execution time than MP-DPC and has fewer adjusted parameters than PI-ICC. In addition, the dead-time compensation scheme successfully suppresses the zero-current clamping effects, and reduce the current THD.

Recently, the increase of burden to operators and lack of skilled operators are the issue in the work of the hydraulic excavator. These problems are expected to be improved by autonomous control. In this paper, we present experimental results of hydraulic excavators using model predictive control (MPC) which incorporates servo mechanism. MPC optimizes digging operations by the optimal control input which is calculated by predicting the future states and satisfying the constraints. However, it is difficult for MPC to cope with the reaction force from soil when a hydraulic excavator performs excavation. Servo mechanism suppresses the influence of the constant disturbance using the error integration. However, the bucket tip deviates from a specified shape by the sudden change of the disturbance. We can expect that the tracking performance is improved by combining MPC and servo mechanism. Path-tracking controls of the bucket tip are performed using the optimal control input. We apply the proposed method to the Komatsu- made micro hydraulic excavator PC01 by experiments. We show the effectiveness of the proposed method through the experiment of digging soil by comparing servo mechanism and pure MPC with the proposed method.

Model predictive control (MPC) has drawn a considerable amount of attention in automotive applications during the last decade, partially due to its systematic capacity of treating system constraints. Even though having received broad acknowledgements, there still exist two intrinsic shortcomings on this optimization-based control strategy, namely the extensive online calculation burden and the complex tuning process, which hinder MPC from being applied to a wider extent. To tackle these two drawbacks, different methods were proposed. Nevertheless, the majority of these approaches treat these two issues independently. However, parameter tuning in fact has double-sided effects on both the controller performance and the real-time computational burden. Due to the lack of theoretical tools for globally analyzing the complex conflicts among MPC parameter tuning, controller performance optimization, and computational burden easement, a look-up table-based online parameter selection method is proposed in this paper to help a vehicle track its reference path under both the stability and computational capacity constraints. matlab-carsim conjoint simulations show the effectiveness of the proposed strategy.

This paper presents a model predictive voltage control method for single-inductor multiple-output (SIMO) DC/DC converters operating in the continuous conduction mode (CCM). The state-space model for a SIMO DC/DC converter system is formulated and a Model Predictive Control (MPC) strategy, which has the capability to track the reference voltage automatically and reduce the impact of cross regulation problem, is proposed to regulate the system. Considering that the switches in the converter only have ON/OFF modes, the quadratic programming algorithm is employed to obtain the MPC's solution. Simulation studies are conducted in MATLAB/Simulink to verify the performance of the proposed method.