Secure Transmission in Wireless Sensor Networks via Reconfigurable Intelligent Surface

Optimizing resource allocation for enhanced urban connectivity in LEO-UAV-RIS networks

This letter investigates an active reconfigurable intelligent surface (RIS)-aided mobile edge computing (MEC) system. Compared with passive RIS, the active RIS is equipped with active reflective amplifier, which can effectively circumvent the “double path loss” attenuation. We propose a joint computing and communication design to minimize the maximum computational latency (MCL), subject to both the phase shift constraints and the edge computing capability constraints. Specifically, the original problem is decoupled into four subproblems, and then the block coordinate descent (BCD) method and the successive convex approximation (SCA) method are applied to alternately optimize the subproblems. The simulation results show that with the same power budget, the performance gain achieved by the active RIS is much larger than that by the passive RIS.

This letter investigates symbol-level security design for a discrete reconfigurable intelligent surface (RIS) enhanced dual-functional radar-communication (DFRC) system. To improve the radar sensing performance, we formulate an optimization problem that jointly addresses the design of space-time transmission waveforms, receiving filters, and discrete reflecting coefficients. The goal is to maximize the minimum radar signal-to-interference-plus-noise ratio (SINR) while ensuring security against eavesdropping. The formulated problem turns out to be intractable due to the practical waveform design restrictions, the discrete RIS coefficient constraints, and the coupling of the optimization variables. To address these issues, we apply the block coordinate descent (BCD) method, incorporating the successive convex approximation (SCA), penalty technique, and the alternating direction method of multipliers (ADMM) algorithm. Simulation results demonstrate the effectiveness of the proposed scheme and show that 2-bit resolution RIS can achieve both satisfactory communication and radar performance close to that achieved with higher resolutions.

International audience

In this paper, energy efficiency (EE) is maximized for the reconfigurable intelligent surface (RIS) aided millimeter-Wave (mmWave) networks with non-orthogonal multiple access (NOMA) and multiple mobile devices. To this end, we first propose the EE optimization, under the constraints of maximum power, minimal rate of devices and constant modulus of beamforming (BF) vectors. Then, the joint resource allocation scheme of power allocation (PA) and BF is designed. Specifically, given PA, an effective iterative algorithm based on the majorizationminimization, concave-convex procedure and block coordinate descent (BCD) is presented to obtain closed-form solutions of suboptimal passive BF (PBF) and analog BF (ABF) for each iteration. Then, given PBF and ABF, an effective iterative algorithm based on the successive convex approximation, BCD and Dinkelbach methods is derived to achieve suboptimal closedform PA for each iteration. By incorporating these two algorithms into the BCD method, a joint optimization algorithm for EE maximization is presented. As a result, joint resource allocation of PA, PBF and ABF is attained. Besides, the convergence and complexity of the algorithms are analyzed. For comparison, the benchmark scheme based on the multidimensional search method and artificial bee colony algorithm is also presented. Simulation results show that the proposed joint scheme is effective and higher EE can be obtained with lower complexity.

Reconfigurable Intelligent Surface (RIS) is an emerging technology that can improve the spectrum and energy efficiency of next-generation wireless networks. However, attaining accurate channel state information (CSI) for the cascaded RIS channel is particularly challenging. Imperfect CSI is a major bottleneck to achieving the spectral efficiency benefit of RIS-assisted networks. Rate splitting (RS), a promising multiple access technology, has been shown to be able to achieve an improved spectrum efficiency and be robust to channel uncertainties. This paper investigates the interplay between RIS and RS by considering a RIS-assisted RS beamforming problem. Active beamforming at the base station (BS) and passive beamforming at the RIS are jointly considered to maximize the minimum user rate under both the perfect CSI case and the imperfect CSI case. A block coordinate descent (BCD) algorithm is developed to solve this non-convex problem. Compared with the conventional semi-definite relaxation (SDR) approach, the proposed method does not require that the covariance matrix of the common beamforming vector be rank-one. Moreover, we present theoretical results to help reveal the impact of the system parameters and explain the performance gain resulting from the integration of RIS and RS. Extensive simulation results are also provided to show that RIS-assisted RS can improve the max-min rate performance significantly compared with conventional multiple access technologies, such as non-orthogonal multiple access (NOMA) and space division multiple access (SDMA) with/without RIS, especially in overloaded systems. With the proposed method, RS shows great potential in combating realistic CSI errors in RIS-assisted networks.

In this paper, we investigate a reconfigurable in-telligent surface (RIS)-based uplink massive multi-input multi-output symbiotic radio system, where each RIS, as an IoT device, enhances the primary transmission from a nearby user to the base station (BS) and simultaneously transmits its own infor-mation to the BS by backscattering modulation. By embedding environmental sensors on the RISs, the proposed system enables the IoT transmission of locally collected environmental data to the BS while assisting the primary transmission. Assuming imperfect channel state information (CSI), we jointly design the active beamforming at the BS and the passive beamforming at the RISs to maximize the weighted sum-rate of both the primary and IoT transmissions. An algorithm based on the block coordinate descent method is proposed to solve it. Simulation results show that the proposed system achieves significant performance gain compared with different baseline schemes. Besides, when the channel estimation error is small, the performance loss due to imperfect CSI is insignificant.

This article investigates the resource allocation of a reconfigurable intelligent surface (RIS)-aided joint communication and sensing (JCAS) system in a coal mine scenario. In the JCAS system, an RIS is implemented at the corner of the zigzag tunnels to improve the complicated wireless environment, where ground obstacles frequently block direct links. In addition, a wireless backhaul base station with a limited energy budget is deployed in the depth of the mine to sense the target area and provide Internet of Things (IoT) services and communication services for users. Furthermore, a data center is placed on the ground to analyze the obtained data and route the communication data. Under this deployment, a joint optimization problem of RIS phase-shift matrix, RIS element switches, and area sensing time is proposed. We aim to maximize the successful sensed bits under total completion time, and maximum transmit power constraints. In order to solve this problem, an iterative algorithm is proposed. The successive convex approximation (SCA)-based algorithm is used for the RIS phase-shift matrix optimization subproblem. For the sensing time optimization subproblem, the quadratic approximation method is proposed to optimize the number of area perceptions. The coordinate descent method is utilized to optimize the RIS element switches. Simulation results show that the energy efficiency is improved by up to 38%, and 7% increases the specific data size compared with the benchmark solutions.

With the development of the next generation of mobile networks, new research challenges have emerged, and new technologies have been proposed to address them. On the other hand, reconfigurable intelligent surface (RIS) technology is being investigated for partially controlling wireless channels. RIS is a promising technology for improving signal quality by controlling the scattering of electromagnetic waves in a nearly passive manner. Heterogeneous networks (HetNets) are another promising technology that is designed to meet the capacity requirements of the network. RIS technology can be used to improve system performance in the context of HetNets. This study investigates the applications of reconfigurable intelligent surfaces (RISs) in heterogeneous downlink networks (HetNets). Due to the network densification, the small cell base station (SBS) interferes with the macrocell users (MUEs). In this paper, we utilise RIS to mitigate cross-tier interference in a HetNet via directional beamforming by adjusting the phase shift of the RIS. We consider RIS-assisted heterogeneous networks consisting of multiple SBS nodes and MUEs that utilise both direct paths and reflected paths. Therefore, the aim of this study is to maximise the sum rate of all MUEs by jointly optimising the transmit beamforming of the macrocell base station (MBS) and the phase shift of the RIS. An efficient RIS reflecting coefficient-based optimisation (RCO) is proposed based on a successive convex approximation approach. Simulation results are provided to show the effectiveness of the proposed scheme in terms of its sum rate in comparison with the scheme HetNet without RIS and the scheme HetNet with RIS but with random phase shifts.

Deep Feedforward Neural Networks' (DFNNs) weights estimation relies on the solution of a very large nonconvex optimization problem that may have many local (no global) minimizers, saddle points and large plateaus. As a consequence, optimization algorithms can be attracted toward local minimizers which can lead to bad solutions or can slow down the optimization process. Furthermore, the time needed to find good solutions to the training problem depends on both the number of samples and the number of variables. In this work, we show how Block Coordinate Descent (BCD) methods can be applied to improve performance of state-of-the-art algorithms by avoiding bad stationary points and flat regions. We first describe a batch BCD method ables to effectively tackle the network's depth and then we further extend the algorithm proposing a \textit{minibatch} BCD framework able to scale with respect to both the number of variables and the number of samples by embedding a BCD approach into a minibatch framework. By extensive numerical results on standard datasets for several architecture networks, we show how the application of BCD methods to the training phase of DFNNs permits to outperform standard batch and minibatch algorithms leading to an improvement on both the training phase and the generalization performance of the networks.

Wireless sensor networks (WSNs) are widely applied in battlefield surveillance, where the data collection (e.g. target tracking or contention zone observation) employed by local sensor nodes needs to send to military bases for tactical decisions. Since data transmissions are susceptible to malicious attacks, jammers of adversaries can successfully block their victim’s communications by transmitting interfering signals to legitimate transmissions. Nowadays, owing to the ability to reconfigure the wireless propagation medium, reconfigurable intelligent surface (RIS) is regarded as an effective tool to enhance transmission performance, especially in the jamming context. This paper considers the anti-jamming communication tactical scenario of a solar-powered RIS network, in which the RIS is used to improve the uplink transmission performance between a wireless device (WD) and a base station (BS). We investigate the long-term anti-jamming communications of the WD powered by a solar energy harvester. Our objective is to jointly assign the optimal amount of transmission energy and the RIS phase shifts to maximize the data rate of the system in the long run. To this end, we formulate an anti-jamming communication optimization problem as a Markov decision process (MDP) framework and then design a deep Q network (DQN)-based algorithm to generate an optimal policy. As a result, the optimal resource allocation is achieved through trial-and-error interactions with environment by observing the predefined rewards and the network state transition. The Python simulation results conducted by averaging 10⁴ time slots show that the proposed algorithm is not only able to learn from environment, but also yields better performance than baseline schemes under network changes. Moreover, the performance of RIS communication schemes is verified to be superior to that of without-RIS communication schemes in the jamming context.

With the wide application of unmanned aerial vehicles (UAVs) in the military and civilian fields, the physical layer security of UAV-assisted communication has attracted more and more attention in recent years. Reconfigurable intelligent surface (RIS) is a revolutionizing and promising technology that can improve spectrum efficiency through intelligent reconfiguration of the propagation environment. In this paper, we investigate the physical layer security of RIS and UAV-assisted communication systems. Specifically, we consider the scenario of multiple eavesdroppers wiretapping the communication between the base station and the legitimate user and propose a secure mechanism that deploys the RIS on a dynamic UAV for security assistance. In order to maximize the average secrecy rate of the system, we propose a joint optimization problem of joint UAV flight trajectory, RIS transmit phase shift, and base station transmit power. Since the proposed problem is non-convex, it is difficult to solve it directly, so we propose a joint optimization algorithm based on block coordinate descent and successive convex optimization techniques. Simulation results verify the effectiveness of our proposed design in improving the secrecy performance of the considered system.

Reconfigurable intelligent surface (RIS) has the potential to significantly enhance the network secure transmission performance by reconfiguring the wireless propagation environment. However, due to the passive nature of eavesdroppers and the cascaded channel brought by the RIS, the eavesdroppers’ channel state information is imperfect at the base station. Under channel uncertainty, the optimal phase-shift, power allocation, and transmission rate design for massive antennas and reflecting elements secure transmission are challenging to solve due to the outage probabilistic constraint with coupled variables. To fill this gap, this paper formulates a problem of energy-efficient secure transmission design with the probabilistic outage constraint. By leveraging the exponential distribution property of the received signal power, the stochastic resource allocation is equivalently transformed into a deterministic one, and the secure energy efficiency maximization problem can be iteratively solved via low complexity first-order algorithms under the alternating maximization (AM) framework. However, due to the nonsmooth problem, the convergence of the objective function value and nature of the converged solution under AM iteration are uncertain. Therefore, the convergence properties with respect to the objective function value and sequence of solutions are further established. Simulation results corroborate the convergence results of the first-order algorithms and show that the proposed algorithm achieves identical performance to the conventional method but saves at least two orders of magnitude in computation time. Moreover, the resultant RIS aided secure transmission significantly improves the energy efficiency compared to baseline schemes of random phase-shift, fixed phase-shift, and RIS ignoring CSI uncertainty.

The following paper presents a reconfigurable intelligent surface (RIS)-aided integrated sensing and communication (ISAC) system model scenario, where a base station communicates with a user, and a bi-static sensing unit, i.e. the passive radar (PR), senses targets using downlink signals. Given that the RIS aids with communication and sensing tasks, this paper introduces new interfering paths that can overwhelm the PR with unnecessarily high power, namely the path interference (PI), which is itself a combination of two interfering paths, the direct path interference (DPI) and the reflected path interference (RPI). For this, we formulate an optimization framework that allows the system to carry on with its ISAC tasks, through analog space-time beamforming at the sensing unit, in collaboration with RIS phase shift and statistical transmit covariance matrix optimization, while minimizing the PI power. As the proposed optimization problem is non-convex, we tailor a block-cyclic coordinate descent (BCCD) method to decouple the non-convex sub-problem from the convex one. A Riemannian conjugate gradient method is devised to generate the RIS and PR space-time beamforming phase shifts per BCCD iteration, while the convex sub-problem is solved via off-the-shelf solvers. Simulation results demonstrate the effectiveness of the proposed solver when compared with benchmarking ones.

Reconfigurable intelligent surface (RIS)-aided mmWave communication offers a promising approach to overcome the issue of severe signal blockage that limits the data rate of mmWave networks. However, joint base station beamforming and RIS phase shift (BF-PS) design presents great challenges not only because of the intricate relationship between the beamforming and phase shift matrices in determining the network sum-rate, but also due to the lack of accurate channel estimation when the number of RIS elements gets large. In this work, we study learning-based BF-PS design for RIS-aided mmWave networks under sparse channel estimation. Our main finding is that, under the practical constraint of pilot overhead for RIS channel estimation, learning-based BF-PS design can yield superior performance to that achieved by the conventional block-coordinate-descent (BCD) algorithm. This work provides an initial study of learning-based BF-PS design under the compressed-sensing framework for mmWave channel estimation. The proposed BF-PS design adopts an enhanced four-stage neural-network architecture that improves upon the existing two-stage design by utilizing outputs from earlier stages to form new features for later stages. The new four-stage design using hybrid beamforming (HBF) outperforms those of the two-stage design using either HBF or fully digital beamforming (DBF).