Secure UHF RFID Authentication With Smart Devices

Passive UHF (ultra high frequency) RFID (radio frequency identification) is a promising technology for products tracking in logistics or routing packages in supply chain. However, passive UHF RFID tag suffers a lot when it is placed on conductive plane or water surface. Many designs like microstrip antenna and ferrite antenna have been used to solve this metal-water problem. But their use is limited by narrow bandwidth and low antenna gain. The electromagnetic band gap (EBG) material which exhibits a unique forbidden band gap at certain frequency offers a potential solution to solve the problem of backside objects effects. Previous research paper indicated that the dipole RFID antenna above three-layer mushroom like EBG material exhibited a good antenna gain and long read range. However, the complicated structure and high material cost greatly limit the application of tag. In this paper, we developed a new type of EBG material which uses ferrite film to reduce size and lower forbidden frequency. A commercial ferrite film which has a high permeability is applied to form two-layer mushroom like EBG material for UHF RFID. This two-layer mushroom like EBG material is a two-layer structure with a ground plane. The design of EBG material for UHF RFID which operates at 915 MHz was discussed in this paper. An EBG tag on metal with a gain of 7 dBi was achieved in simulation. The simulation results showed that the RFID tag still could be read on EBG substrate with a good gain (~7 dBi).

In this paper, the simulation of radiation pattern of the proposed RFID C-slot tag antenna on a coated metallic cylindrical surface is presented. It is found that the radiation pattern in the shadow zone (behind the product) from the proposed RFID tag is stronger than that from the electric current source case (electric tag). Thus, the proposed C-slot tag antenna is useful for the RFID application especially for the curved metallic surface product.

This paper describes the development of four different ultra-high frequency (UHF) radio frequency identification (RFID) tag antenna using polycarbonate material or transparent paper as the substrate and aluminum tape as the radiating element. The main advantage of the method is that the materials are easy to obtain where it can be found in any hardware stores or in any general online shop. Plus, the antennas are designed in such a way that a meander line is traced along the shape of a bowtie antenna so that the antenna would operate at UHF band. The results of all four of the tag antenna designs are discussed and compared using graph obtained from Computer Simulation Technology (CST) simulation results and measurement results obtained from a portable Vector Network Analyzer (VNA) for the reflection coefficient, S 11 , and measurement results taken from VNA in chamber room for the radiation pattern. Finally, the results show that the measured results are in agreement with the simulated result and that the UHF RFID tag antennas are able to operate at UHF RFID band.

Passive UHF (Ultra High Frequency) RFID (Radio Frequency Identification) is a promising technology for products tracking in logistics or routing packages in supply chain. Usually, the UHF RFID antenna is made by etched copper, or aluminum. These etching process introduce chemical wastes during the etching process. Recently, printing silver paste becomes popular due to its environmental friendly manufacturing process. However, there are two drawbacks on printed silver paste RFID antenna. One is low conductivity compared to metal and the other is the high material cost. In this paper, we exam the effects of printing thickness on the performance of UHF RFID tags and summarize the optimized thickness for different read range requirements. A commercial conductive silver paste is printed on PET film as RFID tag antennas. Both finite element simulations and experiments are conducted to evaluate the effects of printed thickness. The simulation results presents that the 10 um thick RFID antenna exhibits relatively good radiation efficiency. The results indicate that 10 um thick RFID tag antenna presents the minimum turn-on power of 18 dBm to 22 dBm which is enough for most applications. The simulation and measurement results present that thinner printed silver paste RFID tag antenna is a potential solution for low cost UHF RFID tags. The cost of these tags could be lower than current etched Al/Cu RFID tags because of material saving.

ABSTRACTIn this research, two low profile metal mountable patch antenna designs for passive ultra-high frequency (UHF) radio frequency identification (RFID) tag are proposed. The complex impedance matching between the antenna and the referenced microchip, Alien-Higgs 3 whose impedance , is realized through an inductively coupled loop feed structure where it provides the needed reactance for the tag antenna. To enhance the bandwidth of the antenna, multiple co-planar radiating patches are employed to excite several resonant modes for worldwide use. The wide impedance bandwidth also compensates for fabrication inaccuracy which could shift the operating frequency of the final antenna design. The final dimensions of the antennas are 87 × 45 × 1.6 mm3 and 130 × 63 × 1.6 mm3. The measured impedance bandwidths of the proposed antennas when mounted on a metal plate are 155 MHz (RL ≥ 3 dB), which is from 830 to 985 MHz, and 117 MHz (RL ≥ 6 dB), which is from 850 to 967 MHz, respectively. The maximum simulated gains are −7 and −11 dB at the operating frequency of 915 MHz. Based on the measurement results, it is expected that the proposed antenna would be able to provide a reasonable read range of at least 2 m throughout the entire UHF RFID band when being attached on metal objects.

This paper discusses the fabrication and wireless performance of 3D-printed graphene-based passive UHF (ultra high frequency) RFID (radiofrequency identification) tags on two different cardboard packaging substrates. Our results confirm that the low-cost and eco-friendly graphene-based RFID tags achieve high performance with attainable read ranges of 3.2–3.8 meters. These results are superior to those of previously reported RFID tags with graphene antennas.

In a pioneering effort, this research presents a distinctive transformation of the Government College University Faisalabad (GCUF) logo into an RFID tag antenna using characteristic mode analysis (CMA), which resonates at the entire ultra-high frequency (UHF) radio frequency identification (RFID) band for IoT applications. The logo of GCUF is simulated in a computer simulation technology (CST) microwave studio to execute its four characteristic modes at 900 MHz. With the implementation of minor changes in the GCUF logo, optimal conjugate impedance matching with the RFID chip has been achieved. The impedance, reflection coefficient, and far-field pattern are examined through CST. The logo tag antenna is fabricated using a Rexin substrate (artificial leather) coated with conductive paint and a passive UHF RFID Alien Higgs H3 chip attached to the logo for impedance matching. The proposed design has been simulated with a human body model. The read range of the fabricated prototype is tested on different objects, like a notebook, T-shirt, and bag. The measured read range demonstrates the robustness of the proposed logo design across various distances: 3 m for a notebook and bag, and 2 m for a T-shirt, with RSSI values of −61 dB, −59 dB, and −62 dB, respectively.

This paper presents the design of ultra-high frequency (UHF) radio frequency identification (RFID) reader antenna using low dielectric constant of microwave substrate. An RFID reader antenna emits electromagnetic signals to the microchip in the tag, and the microchip will be energized by modulating the wave and returns to the reader antenna. The process of wave emitting is known as backscattering due to the presence of tag been detected by the reader. High-dielectric constant substrate, for example flame-retardant-4 (FR4) which is commonly used for microstrip patch antenna, is high in dielectric constant and dielectric loss. Thus, this will lead to low gain and directivity properties of the antenna. To overcome this matter, low-dielectric constant substrate which is Taconic TLY-5 was proposed to be utilized for microstrip patch antenna design. The TLY-5 microstrip substrate thickness used is 1.6 mm, dielectric constant of 2.2, and loss tangent of 0.019. A high-conductivity metal which is typically a conductive copper is been used for the two layers of dielectric substrate, the top radiating patch layer and bottom ground layer where the copper thickness is 0.035 mm. Microstrip feed line is used for this UHF RFID reader antenna. The width of the feed line was tuned to obtain impedance matching of 50 Ω. The proposed antenna which is fork-shaped patch antenna was simulated using Computer Simulation Technology (CST) and Microwave Studio software at resonant frequency of 910 MHz with the outcome results of 7.985 dB gain and −11.11 dB return loss. Nevertheless, the typical value obtained for VSWR is less than 2.

Oilfield tubulars (typically metallic pipes) and other types of oilfield equipment are typically stored in outdoor areas and may be scattered around the field. Managing these types of inventory is challenging and costly, as it requires significant labor resources. Therefore, inventory inaccuracy is common, and data-driven decisions may not be possible in a timely manner. We propose the use of radio frequency identification (RFID) for tracking oilfield tubulars and similar, outdoor-stored, equipment. Our proposed application utilizes passive ultra-high frequency (UHF) RFID technology that enables capturing unique serial identification numbers that are attached to inventory items from a distance of several meters. Passive UHF RFID tags require no batteries to operate. Typical tag cost is low. Each tag is placed on an inventory item and corresponds to a database entry containing specific information about this item. The tag communicates its serial number using power provided by an RFID reader radio transmission. The RFID reader is securely mounted to the underside of a UAV flown over the field. Captured RFID tags are either stored locally and retrieved once the UAV lands, or are wirelessly transmitted to a constantly updating inventory database. In addition to tag ID, the captured data typically includes time and date stamp, as well as location data. This research project included the design and manufacturing of an enclosure to house a RFID reader system which includes a host computer, embedded reader, antenna, power source, and necessary components for user interface. Specialized mounts were designed and manufactured to attach the enclosure and antenna to the UAV. The project incorporated the development of "middleware", specialized software installed on the host computer to communicate with the reader. The reader handles low-level communication with the antenna. To reduce network traffic, event management and data filtering are efficiently performed. The results of several UAV flights in experimental areas are presented and discussed. Various brands of passive RFID tags for oilfield applications were tested. Particular attention was given to population density of the items, stacking configuration, vertical altitude distance between reader and tags, and time to collect inventory data for a given area of surveillance. As RFID applications are increasing in the oil, gas, solar, and other sectors of the energy production industries, UAVs can effectively be used to get important operational and inventory data. UAV use is particularly appealing in inaccessible and remote locations.

The design of an ultrahigh-frequency (UHF) radio-frequency identification (RFID) reader antenna covering an electrically large near-field area is challenging for near-field UHF RFID applications. In such a design, magnetic field distribution on a large coverage area is required to be as uniform as possible. For some specific UHF near-field RFID applications, given radiation pattern characteristics are expected. A fragment-type wire structure is quite suitable for these demands because uniform magnetic field distribution and given patterns could be generated through optimizing the fragmented wires in a designated electrically large area to obtain corresponding current distribution. In this article, the concept of a fragment-type structure as well as some design guidelines are reviewed and summarized. Then, two omnidirectional fragment-type wire antennas with different cell size and two directional fragment-type wire antennas are designed. Both simulation and experiment results show that there is no reading null within an electrically large near-field zone having a perimeter of four operating wavelengths at 915 MHz (i.e., 320 mm x 320 mm). The omnidirectional designs are promising in the applications of UHF near-field RFID tag detection in self-confined volumes, and the directional designs are potential in the systems of UHF near-field/far-field RFID.

Radio frequency identification (RFID) provides great potential for different Internet of Things (IOT) applications. In the future, material choices in these IOT devices will have a huge effect on the environment and thus use of renewable materials is a growing trend. In this paper, passive ultra high frequency (UHF) RFID tags were inkjet-printed directly on wood, paper, and cardboard substrates, and their performance was evaluated by measuring two key properties: threshold power and theoretical read range. According to our measurements, the tags on wood showed read ranges of 7 - 8 meters, the tags on cardboard exhibited read ranges of 4 - 7 meters, and the tags printed on paper showed read ranges of 2 - 7 meters through the global UHF RFID band. According to these results, the performance of these inkjet-printed UHF RFID tags is sufficient for many IOT devices and potential applications e.g. in construction and packaging industry.

This paper presents a 2-D localization system based on phase-of-arrival evaluation of passive ultrahigh frequency (UHF) radio frequency identification (RFID) transponders. To handle the ambiguity caused by phase evaluation, several tags are arranged to form a uniform linear array. A multiple input multiple output system, where sequentially each frontend is configured to work as transmitter, while the remaining frontends serve as receivers, is used to enable position estimation. For proof of concept, a local position measurement system demonstrator was built comprising conventional passive EPCglobal Class-1 Gen-2 UHF RFID tags, one commercial off-the-shelf RFID reader, several transceiver frontends, baseband hardware, and signal processing. Measurements were carried out in an indoor office environment, where the $3.5~{\rm m} \times 2.5$ m measurement zone was surrounded by drywalls and concrete floor and ceiling, and the experimental results showed robust and accurate localization with a root-mean-square deviation of 0.011 m and a maximum error of 0.032 m. These experimental results were confirmed by simulations, which were performed to determine the limits of the system accuracy.

ABSTRACTThis article investigates the effects of the environment on ultrahigh frequency (UHF) radio frequency identification (RFID) tags in both the near‐field and far‐field. Item‐level tagging has always been challenging due to the negative impact of metals on RFID. Full‐scale RFID item‐level tagging has always been difficult to integrate in retail (department) stores. This UHF RFID feasibility research examines the technical differences between near‐field and far‐field coupling by testing theoretical hypotheses through empirical experiments. These experiments are based on a specific case‐study, where a distributor wants to tag multimedia objects. Based on the results obtained, we found that metal had less effect on the RFID tags in the near‐field than in the far‐field. In both cases the RFID tag was not readable, when placed directly onto metal. When the multimedia object itself was tagged, the reading range decreased to around half the free‐space reading range in near‐field and far‐field. We can conclude that the RFID implementation in the retail store is feasible, but depends to a large extent on the product and its environment. © 2014 Wiley Periodicals, Inc. Microwave Opt Technol Lett 56:718–727, 2014

A compact loop antenna is presented for mobile ultrahigh frequency (UHF) radio frequency identification (RFID) application. This antenna, printed on a 0.8 mm thick FR4 substrate with a small size of 31 mm × 31 mm, achieves good impedance bandwidth from 897 to 928 MHz, which covers USA RFID Band (902–928 MHz). The proposed loop configuration, with a split-ring resonator (SRR) coupled inside it, demonstrates strong and uniform magnetic field distribution in the near-field antenna region. Its linearly polarized radiation pattern provides available far-field gain. Finally, the reading capabilities of antenna are up to 56 mm for near-field and 1.05 m for far-field UHF RFID operations, respectively.

This research is concerned with a multiple loop antenna applicable to near field ultra-high frequency (UHF) radio frequency identification (RFID). The proposed multi-loop antenna is configured to induce the robust and even magnetic field distributions in the Hx, Hy, and Hz orientations so as to achieve the enhanced readability performances in all directions (i.e., x, y, and z). Simulations were carried out using CST Microwave Studio to determine the impedance bandwidth (|S11|<−10 dB) in the frequency range of 920–925 MHz (i.e., Thailand's UHF RFID standard) and to investigate the Hx-, Hy-, and Hz-oriented magnetic field distributions. A prototype antenna of 14 cm × 16 cm × 0.6 mm (W × L × H) in overall dimension was subsequently fabricated on an FR4 substrate connected to a coaxial cable. In this research, the Hx-, Hy-, and Hz-oriented magnetic field distributions of the prototype antenna were measured in the x-axis, y-axis, and x–y plane and are in good agreement with the simulation results. The measured readability performances in the x-, y-, and z-directions in which seven near field UHF RFID tags were deployed unobstructed (i.e., in open air) are respectively 25.27%, 31.73%, and 85.43%. Furthermore, the performances on the antenna readability with the tags attached to the microcentrifuge tubes are 30.55%, 25.90%, and 69.09% for the x-, y-, and z-directions. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:402–417, 2016.