Selection between Radio Frequency and Visible Light Communication Bands for D2D

In order to counteract the explosive escalation of wireless tele-traffic, the communication spectrum has been gradually expanded from the conventional radio frequency (RF) band to the optical wireless (OW) domain. By integrating the classic RF band relying on diverse radio techniques and optical bands, the next-generation heterogeneous networks (HetNets) are expected to offer a potential solution for supporting the ever-increasing wireless tele-traffic. Owing to its abundant unlicensed spectral resources, visible light communications (VLC) combined with advanced illumination constitute a competent candidate for complementing the existing RF networks. Although the advantages of VLC are multi-fold, some challenges arise when incorporating VLC into the classic RF HetNet environments, which may require new system architectures. The user-centric (UC) design principle for VLCVLC environments constitutes a novel and competitive design paradigm for the super dense multi-tier cell combinations of HetNets. The UC concept may be expected to become one of the disruptive techniques to be used in the forthcoming fifth-generation era. This paper provides a comprehensive survey of visible-light-aided OW systems with special emphasis on the design and optimization of VLC networks, where the radically new UC design philosophy is reviewed. Finally, design guidelines are provided for VLC systems.

In this paper, we consider a cooperative device-to-device (D2D) communication system, where the D2D transmitters (DTs) act as relays to assist the densified cellular network users (CUs) for transmission quality of service (QoS) improvement. The proposed system achieves a win-win situation, i.e. improving the spectrum efficiency of the CUs that cannot meet their rate requirement while providing spectrum access for D2D pairs. Unlike previous works, to reduce the overhead, we design a novel two-timescale resource allocation scheme, in which the pairing between CUs and D2D pairs is decided at a long timescale and transmission time for CU and D2D pair is determined at a short timescale. Specifically, to characterize the long-term payoff of each potential CU-D2D pair, we investigate the optimal cooperation policy to decide the transmission time based on the instantaneous channel state information (CSI). We prove that the optimal policy is a threshold policy which can be achieved via binary search. Since CUs and D2D pairs are self-interested, they are paired only when they agree to cooperate mutually. Therefore, to study the cooperation behaviors of CUs and D2D pairs, we formulate the pairing problem as a matching game, based on the long-term payoff achieved by the optimal cooperation policy of each possible pairing. Furthermore, unlike most previous matching models in D2D networks, we allow transfer between CUs and D2D pairs to improve the performance. To solve the pairing problem, a distributed algorithm is proposed, which converges to an ϵ-stable matching. We show that there is a trade-off between the optimality and the computational complexity of the algorithm. We also analyze the algorithm in terms of the robustness to the unilateral deviation of D2D pairs. Finally, the simulation results verify the efficiency of the proposed matching algorithm.

Recently, visible light communication (VLC) system has gained attention due to its higher data rate, wider spectrum, higher security, lower weight, extensive lifespan of LEDs, smaller sizes of apertures and lower power consumption, lower cost, and no health issues etc. The VLC is used to strengthen the radio frequency (RF) communication and it also improves the communication performance in short range such as homes, offices, corridors, hospitals, aircrafts etc. The VLC provides dual functionality, that is, illumination and communication through the same LED simultaneously. It needs fast switching of LED (which is not detectable by human eyes) along with some appropriate modulation schemes for VLC to provide communication and illumination simultaneously. Meanwhile, LED should be powered on for the duration of communication, which conversely creates two challenges. First, the LED would consume more electrical power, which makes the system expensive. Second, LED can also be used in a dimming mode to save the power. Dimming of LED decreases the data rate. The data rate is inadequate due to modulation bandwidth of high brightness LED. The power and the data rate can be achieved by using different modulation schemes or line encoding schemes. There are a number of other factors such as interference of sun light, reflection of mirror or other fluorescent or candescent light disturbing the communication due to visible light usage in communication, interference to other VLC devices, integration of VLC with existing architecture of communication system, that is, Wi-Fi. The rest of the chapter is organized as follows. Section 1.1 gives an overview of VLC, followed by the brief discussion on the VLC system architecture in Section 1.2. Section 1.3 highlights the applications of the VLC. The general modulation schemes are given in Section 1.4. Then, Section 1.5 discusses the power efficient techniques, spectral efficient techniques are covered in Section 1.6, and Section 1.7 demonstrates the interference cancellation techniques. This chapter also discusses a comparison of different modulation techniques in terms of power efficiency, spectral efficiency, and interference cancellation and concludes with the best suited technique for power, spectrum, and interference.

In a device-to-device (D2D) underlaid cellular network, there exist two types of co-channel interference. One type is inter-layer interference caused by spectrum reuse between D2D transmitters and cellular users (CUEs). Another type is intra-layer interference caused by spectrum sharing among D2D pairs. To mitigate the inter-layer interference, we first derive the interference limited area (ILA) to protect the coverage probability of cellular users by modeling D2D users’ location as a Poisson point process, where a D2D transmitter is allowed to reuse the spectrum of the CUE only if the D2D transmitter is outside the ILA of the CUE. To coordinate the intra-layer interference, the spectrum sharing criterion of D2D pairs is derived based on the (signal-to-interference ratio) SIR requirement of D2D communication. Based on this criterion, D2D pairs are allowed to share the spectrum when one D2D pair is far from another sufficiently. Furthermore, to maximize the energy efficiency of the system, a resource allocation scheme is proposed according to weighted graph coloring theory and the proposed ILA restriction. Simulation results show that our proposed scheme provides significant performance gains over the conventional scheme and the random allocation scheme.

Visible light communication (VLC) reuses illumination devices, particularly light-emitting diodes (LEDs), for communication purposes. It has great potential to alleviate the strain on radio-frequency spectrum in indoor environments. VLC-enabled LED luminaries form VLC attocells that carry downlink data traffic to indoor mobile or stationary terminals. While one of the advantages of indoor VLC is low interference due to natural cell boundaries such as walls, multiple VLC attocells within a room would interfere. This is because illumination requirements often mandate a rich overlap of emissions of luminaries in a room. In this paper, we suggest the coordination of multiple VLC attocells (i.e., VLC-enabled LED luminaries) to turn the problem of overlap and thus interference into an advantage. We stipulate that this coordination can be accomplished through power line communication, which has been considered before as a means to transport data to VLC transmitters. Borrowing from concepts developed for radio-frequency wireless communications, we develop several precoding schemes for the new coordinated VLC broadcasting architecture. These include designs for the case of imperfect channel knowledge at the VLC transmitter, since channel information is usually provided through a low-rate feedback channel. The performance advantages for VLC transmission due to the proposed coordination and precoding designs are demonstrated based on a set of numerical results.

The proposed Q-learning optimized Internet of Things (IoT) integrated VLC system is highly suitable for indoor environments where electromagnetic interference (EMI), device density and real-time data transmission are critical challenges. Visible Light Communication (VLC) serves as an effective alternative to traditional RF communication by utilizing existing LED lighting infrastructure for dual-purpose illumination and data transmission. In such indoor settings the system enables real-time monitoring and secure transmission of vital information such as environmental data to an IoT-based cloud platform. The use of VLC in the visible light spectrum eliminates EMI making it ideal for environments where Radio Frequency (RF) communication is either restricted or unreliable. To adapt to dynamic indoor conditions such as human movement or changing light intensities the system employs Q-learning to continuously optimize transmission parameters like modulation index and power levels. This reinforcement learning approach ensures enhanced link reliability, reduced Bit Error Rate (BER) and stable communication under fluctuating indoor conditions. Additionally, the incorporation of Enhanced Asymmetrically Clipped Duty-Cycled Optical OFDM (EACDO-OFDM) improves spectral efficiency and power utilization thus making the solution energy-efficient and scalable for large-scale indoor IoT deployments. By integrating adaptive machine learning techniques with VLC and IoT the system delivers robust, intelligent and energy-conscious communication, well-suited for smart building automation, indoor sensing and real-time monitoring applications.

Patient health monitoring technology presents great potential for future healthcare applications and Radio Frequency (RF) communication is the most popular medium for its implementation. This paper presents a static indoor patient monitoring scheme using uplink Visible Light Communication (VLC) suitable for hospital environments. VLC is considered instead of RF communication because of health concerns regarding continuous RF exposure to patients for health monitoring. The proposed scheme is designed for transmitting uplink patient data using VLC through On-Off Keying (OOK) modulation. Experiments were conducted with several body-sensors data transmitted using predefined headers. The experiment results show that the proposed VLC based patient monitoring scheme can offer accurate monitoring data transmission with minimal interference with the help of space diversity.

The quest to meet diverse services and applications that are emanating from the increasing inter-connected devices including machine-to-human communication has brought about consideration of massive deployment of small cells for fifth generation (5G) and Beyond network. With densification of small cells, mm-wave and THz frequencies play significant role in delivering mobile services. Consequently, supporting radio frequency (RF) communication with visible light communications (VLC) link exhibits potentials to ameliorate the challenges of RF communication especially bandwidth limitations and interference. Capitalising on the strength of VLC, we propose a basic end-to-end system to experimentally evaluate the suitability of VLC as fronthaul using real-time mobile traffic. Successful downlink (DL) transmission was achieved via VLC. To investigate the performance of the VLC link, transmission signal-to-noise ratio (SNR) and throughput of the VLC and RF Links are measured and compared. The light emitting diodes (LEDs) and Photo-diodes (PD) have shown to have significant effects on the performance of the VLC link. However, the results establish a fundamental premise for the suitability of VLC as fronthaul for small cell network.

The dual property of LEDs to facilitate illumination and Communication concurrently has driven Visible Light Communication (VLC) as an emerging technology and a promising alternative to Radio Frequency (RF) Communication. The primary objective of VLC is to increase the data rates and to have better performance of the networks especially for indoor applications. In this juncture, for the purpose of increasing the Information Spectral Density (ISD), Fast Optical Orthogonal Frequency Division Multiplexing (FOOFDM) can be exploited. In this work, the performance of FOOFDM is evaluated by employing various channel estimation algorithms and Probability of Error expression is derived for the developed system models. In addition, investigations on channel estimation in DC Biased Optical OFDM (DCO-OFDM) is carried out where, the result analysis emphasize that, FOOFDM is superior in terms of both power efficiency and spectral efficiency when compared to DCO-OFDM. Employing a real-valued transform and its simple one dimensional modulation, makes FOOOFM to exhibit lower computational complexity when compared with hermitian symmetry imposed optical OFDM (DCO-OFDM).

Simultaneous Wireless Information and Power Transfer (SWIPT) technique is introduced in Radio Frequency (RF) communication to carry both information and power in same medium. In this approach, the energy can be harvested while decoding the information carries in an RF wave. Recently, the same concept applied in Visible Light Communication (VLC) namely Simultaneous Light Wave Information and Power Transfer (SLIPT), which is highly recommended in an indoor applications to overcome the problem facing in RF communication. Thus, SLIPT is introduced to transmit the power through a Light Emitting Diode (LED) luminaries. In this work, we compare both SWIPT and SLIPT technologies and realize SLIPT technology archives increased performance in terms of the amount of harvested energy, outage probability and error rate performance.

We consider a cooperative device-to-device (D2D) communication system, where the D2D transmitters (DTs) act as relays to assist cellular users (CUs) in exchange for the opportunities to use the licensed spectrum. To reduce the overhead, we propose a novel two-timescale resource allocation scheme, in which the pairing between CUs and D2D pairs is decided at a long timescale and time allocation factor for CU and D2D pair is determined at a short timescale. Specifically, to characterize the long-term payoff of each potential CU-D2D pair, we investigate the optimal cooperation policy to decide the time allocation factor based on the instantaneous channel state information (CSI). We prove that the optimal policy is a threshold policy. Since CUs and D2D pairs are self-interested, they are paired only when they agree to cooperate mutually. Therefore, to study the behaviors of CUs and D2D pairs, we formulate the pairing problem as a matching game, based on the long-term payoff of each possible pairing. Furthermore, unlike most previous matching model in D2D networks, we allow transfer between CUs and D2D pairs to improve the performance. Besides, we propose an algorithm, which converges to an epsilon-stable matching.

For device-to-device (D2D) communication under laid in a cellular network with uplink resource sharing, both cellular and D2D pairs may cause significant inter-cell interference (ICI) at a neighboring base station (BS). In this paper, under optimal BS receive beamforming, we jointly optimize the power of a cellular user (CU) and a D2D pair for their sum rate maximization, while satisfying minimum SINR requirements and worst-case ICI limit in multiple neighboring cells. We solve this non-convex joint optimization problem in two steps. First, the necessary and sufficient condition for the D2D admissibility under given constraints is obtained. Finally, we consider joint power control of the CU and D2D transmitters. We propose a power control algorithm to maximize the sum rate. Depending on the severity of ICI that D2D and CU may cause, we categorize the feasible solution region into five cases, each of which may further include several scenarios based on minimum SINR requirements. The proposed algorithm is optimal when ICI to a single neighboring cell is considered. For multiple neighboring cells, we provide an upper bound on the performance loss by the proposed algorithm and conditions for its optimality. We further extend our consideration to the scenario of multiple CUs and D2D pairs, and formulate the joint power control and CU-D2D matching problem. We show how our proposed solution for one CU and one D2D pair can be utilized to solve this general joint optimization problem. Simulation demonstrates the effectiveness of our power control algorithm and the nearly optimal performance of the proposed approach in the setting of multiple CUs and D2D pairs.

For visible light communication (VLC), the light signals are transmitted without optical fibers or any sort of wave-guiding. Due to the inherent broadcast nature, physical-layer security emerges as a promising method to protect information delivery from eavesdropping. As for the secrecy capacity of VLC channel, there exist two features. In one way, the limited optical power makes the common capacity expressions in radio-frequency (RF) communication unapplicable for VLC. In another way, several correlated geometrical parameters directly alters the Lambertian model of indoor VLC channel, which gives the secrecy capacity more meanings. However, the issue considering both aspects has not been studied recently. In this paper, from the practical scenarios, we extract a typical geometrical model to reveal the mobility principles of the legitimate receiver and the eavesdroppers. Then, we character two typical distributions of the geometrical parameter. Correspondingly, we derive the upper and lower bounds on the average secrecy capacity, which have the closed forms. Finally, simulation results show that our upper and lower bounds are tight at high optical signal-to-noise rates (OSNRs). Moreover, the geometrical features of VLC systems and distribution parameters of the receiver mobility are effectively reveal by the bounds.

The paper focuses on the need for optical communication in future eras. Spatial reprocess cannot meet the present conditions with increasing traffic demand in Radio Frequency (RF) communication. The frequency spectrum in traditional methods of wireless communication has been saturated. Visible Light Communication (VLC) and Internet-of-Things (IoT) integration will open up many indoor applications in the near future. Light Emitting Diodes (LEDs) and Photodetectors (PDs) in VLC support reliable uplink and downlink for Device-to-Device communication indoors. There is emergence of the energy-efficient variant of the VLC due to the shortage of energy budget in the upcoming era. The VLC works well in low illuminance. Energy conservation is supportedby consuming much lower energy through the usage of LEDs in VLC.This can be achieved through the hybrid of single and multicarrier modulation. The work is about to discuss dimming techniques that support VLC in low illuminance and multicarrier modulation, which supports high data rate transmission.

Visible Light Communication (VLC) has emerged as an attractive alternative to radio frequency (RF) communication, due to cost-effectiveness and being license free. It has also proved its applicability in automotive applications, as an alternative and/or a complement to the traditional RF-based communications. We investigate the suitability of VLC in Intelligent Transportation Systems (ITS) and discuss its advantages in terms of safety enhancement and improved efficiency of the ITS. In this thesis, a VLC-based Vehicle-to-Vehicle (V2V) system in practical environments, considering both Line-of-Sight (LOS) and Non-Line-of-Sight (NLOS) paths are presented. The thesis investigates robust communication between a Light Emitting Diodes (LEDs) based VLC emitter and Photodiodes (PDs) based VLC receiver. For consideration of a V2V communication system, we consider transmitter on vehicle headlights and receivers on taillight making 2 _ 2 Multiple-Input-Multiple-Output (MIMO) communication link. A closed-form expression of the Channel Impulse Response (CIR) is derived and the effect of various channel parameters is analyzed. Optical-Orthogonal Frequency Division Multiplexing (O-OFDM) with adaptive modulation schemes is proposed for system improvement. Its performance is evaluated in terms of Inter Symbol Interference (ISI) mitigation, and data rate improvement. Moreover, the effect of sunlight on the V2V-VLC Two denoising schemes are proposed and evaluated as a solution to combat the effect of the solar irradiance on the VLC signal. Firstly, we use a differential receiver for denoising purposes followed by k-Nearest Neighbour (kNN) based adaptive _ltering algorithm, which is a supervised Machine Learning (MLE) technique. The shadowing effect is also studied. Moreover, an application of VLC in Foglet based ITS is described. The simulation validation of the VLC-based V2V system is performed under various environmental conditions and scenarios. Obtained results emphasize the suitability of VLC technology for automobile applications,.