Self-sustained pulsation in vertical-cavity surface-emitting lasers under external optical feedback

This work focuses on the effects of external feedback on the transient response of antiresonant reflecting optical waveguide (ARROW) vertical cavity surface emitting lasers (VCSELs). The study uses a self-consistent system, which is incorporated by the field transfer matrix method, laser rate equations and the reflective index change model, to simulate the dynamics of the VCSELs under optical feedback.

This study introduces an accurate non-linear distortion analysis for vertical cavity surface emitting lasers (VCSELs) based on Volterra series approach in directly modulated scheme. Closed-form expressions of the optical response of VCSELs in terms of modulation response, harmonic distortions, and second- and third-order intermodulation distortions are derived. The impact of external optical feedback on the VCSEL's response and intermodulation distortion is investigated. Moreover, the suggested non-linear model avoids the numerical solution of laser rate equations and provides in detail a non-linear distortion analysis of VCSELs.

Random source is important for the security of key distribution. In this paper, a novel secure key distribution scheme based on unidirectional injection of vertical cavity surface emitting laser (VCSEL) system is proposed. In the proposed scheme, a chaotic signal without time delay signature is generated by a VCSEL subject to unidirectional optical injection, which is regarded as a master laser. The chaotic signal generated by the master VCSEL is further injected into two slave VCSELs to obtain synchronized bandwidth-enhanced chaotic signals. After that, by sampling, quantizing and XOR operation on the two synchronized chaotic signals, two key streams can be obtained. Based on the well-known spin-flip model, the time delay signature of chaotic signals generated by master VCSEL and the synchronization performance between the master VCSELs and two slave VCSELs are numerically investigated in detail. It is shown that by the unidirectional injection, the chaotic outputs can be achieved in the master VCSEL in a wide range of frequency detuning and coupling strength. More importantly, no time delay signature can be observed in the auto correlation function of the chaotic intensity time series generated by the master VCSEL. Besides, we find that high quality synchronization is achieved between the bandwidth-enhanced chaotic signals generated by two slave VCSELs under the common driving of master VCSEL. The synchronization coefficient between two slave VCSELs increases up to 0.99, and the synchronization coefficient between master VCSEL and salve VCSEL is only 0.74. Note that such a high quality synchronization between two slave VCSELs while relatively low quality synchronization between the master and slave VCSEL is conducible to ensuring the security of key distribution. In addition, the effects of tunable parameters on key bit error rate are considered, and two quantization methods are employed for comparison. Numerical simulation results show that the key bit error rate between two legitimate users is as low as 1%, and the key bit error rate between legitimate user and eavesdropper is higher than 10% in the single-threshold case; the bit error rate can even be as low as 10-6 in the double-threshold case. The influence of parameter mismatch on key bit error rate is also discussed, and it is suggested that two salve VCSELs should be finely matched to ensure low bit error rate. Finally, NIST randomness test is performed for the generated key streams. Hence, the proposed scheme enhances the security of key distribution, which is valuable for further developing the chaos communication systems.

We numerically investigate how polarization properties of vertical cavity surface emitting lasers (VCSELs) are affected by optical feedback from an extremely short external cavity. In order to do it we use a two modes rate equation model that accounts for infinite round trips in the external cavity. With it we perform maps of bistability finding out a modulation of the polarization switching currents when increasing the external cavity length with a period equal to half the wavelength of operation of the device. When the external mirror reflectivity is high enough there is a region within each period of modulation where the VCSEL polarization is stable at any injected current within the operation range. Moreover, using polarized feedback the map of bistability is channelled and the bistable region is almost suppressed. A preliminar study of the effects of temperature variations on the map of bistability is also carried out and presents polarized feedback as a more robust technic to obtain polarization stabilization. An experimentally obtained map of bistability supports the model showing very good agreement with it.

Remarkable progress made in performance characteristics and reliability of high-speed (> 10 GHz) 850-nm multi-mode (MM) oxide-confined vertical cavity surface emitting lasers (VCSELs) during the last decade has led them to find applications in space satellite systems. The main advantage of deploying high-speed VCSELs in space satellites over directly modulated 850-nm edge emitting lasers is the absence of COMD (catastrophic optical mirror damage). In recent years, leading VCSEL manufacturers introduced higher speed (~ 20 GHz or 25 Gbps) VCSELs with encouraging characteristics. However, little has been reported on reliability and failure modes of these state-of-the-art VCSELs although it is crucial to understand failure modes and degradation mechanisms in these VCSELs through physics of failure investigation and subsequently develop VCSELs that exceed lifetime requirements for space satellite systems. For the present study, we performed short-term and long-term accelerated life-tests on 25 Gbps oxide-confined MM VCSELs to study reliability of these devices. Our goal is to extract credible reliability model parameters (thermal activation energy and current exponent factor) from these life-tests to determine suitability of these lasers for future space satellite systems. We also performed failure mode analysis on VCSELs at different stages of degradation using various techniques. We employed nondestructive techniques including optical beam induced current (OBIC) and electron beam induced current (EBIC) techniques as well as destructive techniques including focused ion beam (FIB) and high-resolution TEM techniques. Our detailed reliability and failure mode analysis results are reported along with our understanding on the physical origin of degradation in high-speed VCSELs with strained InGaAs quantum wells.

Vertical cavity surface emitting laser (VCSEL) is an important laser source for their evident plentiful applications in optical communication. The present investigation reports a comparison of the modeling and optimization of long wavelengths 1310 nm and 1550 nm high speed short cavity VCSEL for continuous wave operation at various temperature (283-3230K) for various diameters. The continuous wave lasing is demonstrated for the device diameter from 2 to 5 μm with threshold current of 1.07-1.33 mA with threshold power consumption of 1.86-2.57 mW for 1310 nm and threshold current of 0.94-1.24 mA and threshold power consumption 1.67-2.1 mW for 1550 nm VCSEL. The results demonstrate that the threshold current, peak emitted power and power consumption increases with the increase in device diameter. The results confirm that VCSELs with 2 μm diameter is most suitable to achieve energy-efficient operation. Although rollover current increases with the diameter, but, due to the advantage of lower threshold current and power consumption, VCSEL having smaller diameter is best suited. The power conversion efficiency for proposed long wavelength VCSELs is approximately 50% which is extremely useful for low power applications. The proposed VCSELs are suitable for very short reach (<2 m) optical interconnects such as chip-to-chip and board-to-board communication in high performance computers.

Improved carrier confinement and stimulated recombination rate in GaN-based vertical-cavity surface-emitting lasers with buried p-AlGaN inversion layer

We introduced the vertical cavity surface emitting laser (VCSEL) as the laser diode in tour external cavity system. Because VCSELs are now commercially available, and the External cavity diode laser (ECDL) systems using them are expected to improve their frequency stability, we have replaced a Fabry-Perot type laser diode with a VCSEL, and examined its oscillation-frequency stability. Therefore we were able to expect that the VCSELs with our double optical feedback system have good oscillation frequency stability. The obtained VCSEL's oscillation-frequency stability, i.e., the square root of Allan variance &sigma; was 4&times;10^-10, at an averaging time of &tau;=1 sec.

High-performance 808 nm double and triple-junction vertical cavity surface emitting lasers (VCSELs) are designed and investigated. The light-current-voltage (L-I-V) characteristics of 808-nm single, double, and triple-junction VCSELs are compared. In the paper, the double-junction VCSELs with two oxide apertures exhibit a very high slope efficiency (SE) of 2.32 W/A at 25 °C, and the peak SE of 2.51 W/A is achieved at 10 °C. The power conversion efficiency (PCE) of 53.14% is achieved for double-junction individual VCSEL emitter. The peak SE of the triple-junction VCSELs reach 3.40 W/A with the PCE of 53.02% for individual VCSEL emitter. Under narrow pulse test conditions (400 Hz, 60 ns pulse width), the peak output powers of the designed double-junction and triple-junction VCSEL arrays reach 216.11 W and 325.77 W under the injection current of 80 A, respectively. Such high-performance multi-junction 808-nm VCSELs are very important for pumping solid state lasers and medical aesthetics.

Multimode VCSEL(Vertical Cavity Surface Emitting Laser) coupling into MMF (Multimode Optical Fiber) and its influence on MMF link has been numerically studied. Considering the transverse misalignment between VCSEL and MMF, coupling efficiency between VCSEL higher-order modes and modes of MMF is calculated and the Mode Power Distribution in the MMF is obtained. Simulation of MMF link with multimode VCSEL indicates that the higher-order VCSEL modes lead to decreasing of the eye opening of received signal. The transverse misalignment of VCSEL between MMF greatly deteriorates the eye opening. With 300m OM3-MMF link , the EOP (eye-opening-penalty) is greater than 14dB when the misalignment between VCSEL and MMF is lager than 5&mu;m.

This paper is going to review the state-of-the-art of the high-speed 850/940-nm vertical cavity surface emitting laser (VCSEL), discussing the structural design, mode control and the related data transmission performance. InGaAs/AlGaAs multiple quantum well (MQW) was used to increase the differential gain and photon density in VCSEL. The multiple oxide layers and oxide-confined aperture were well designed in VCSEL to decrease the parasitic capacitance and generate single mode (SM) VCSEL. The maximal modulation bandwidth of 30 GHz was achieved with well-designed VCSEL structure. At the end of the paper, other applications of the near-infrared VCSELs are discussed.

High electro-optical conversion efficiency is one of the most distinctive features of semiconductor lasers as compared to other types of lasers. Its further increase remains a significant objective. Further enhancing the efficiency of edge-emitting lasers (EEL), which represent the highest efficiency among semiconductor lasers at present, is challenging. The efficiency of vertical cavity surface emitting lasers (VCSELs) has always been relatively low compared to EEL. This paper, combining modeling with experiments, demonstrates the potential of multi-junction cascaded VCSELs to achieve high efficiency beyond that of EELs, our simulations show, that a 20-junction VCSEL can achieve an efficiency of more than 88% at room temperature. We fabricated VCSEL devices with different numbers of junctions and compared their energy efficiency. 15-junction VCSELs achieved a maximum efficiency of 74% at room temperature under nanosecond driving current, the corresponding differential quantum efficiency exceeds 1100%, being the largest electro-optical conversion efficiency and differential quantum efficiency reported until now for VCSELs.

We present a transmission method to determine the polarization axis fluctuations for VCSEL (Vertical Cavity Surface Emitting Laser). The research is focused mainly on commercial lasers operatingat 780 nm, designed forlaser spectroscopy. The angle fluctuation of the laser linear axis polarization iselaborated to be less than 150 mrad. Measurement errors of this method are studied and calculated. The measurement uncertainty is ?1,4 mrad andthis is equivalent to ? 5? of arc.Changes of the linear polarization axis depending on the laser current and temperaturearepresented. Full Text: PDF References T. Ohtoshi et al., "Dependence of optical gain on crystal orientation in surface?emitting lasers with strained quantum wells", Appl. Phys. Lett.63, 1886 (1994). CrossRef K. Tateno et al., "Growth of vertical-cavity surface-emitting laser structures on GaAs (311)B substrates by metalorganic chemical vapor deposition", Appl. Phys. Lett.70, 3395 (1997). CrossRef O. Tadanaga et al., "An 850-nm InAlGaAs strained quantum-well vertical-cavity surface-emitting laser grown on GaAs (311)B substrate with high-polarization stability", IEEE Photon. Tech. Lett.12, 942 (2000) CrossRef K. Choquette, R. Leibenguth, "Control of vertical-cavity laser polarization with anisotropic transverse cavity geometries", IEEE Photon. Tech. Lett. 6, 40 (1994) CrossRef B. Weigl et al., "High-performance oxide-confined GaAs VCSELs", IEEE J. Sel. Top.Quantum Electron. 3, 409 (1997) CrossRef P. Dowd et al., "Complete polarisation control of GaAs gain-guided top-surface emitting vertical cavity lasers", Electron. Lett. 33, 1315 (1997) CrossRef M. Grabherr et al., "Volume production of polarization controlled single-mode VCSELs", Proc. SPIE,6908, 690803 (2008) CrossRef R. Roy et al., "First-Passage-Time Distributions under the Influence of Quantum Fluctuations in a Laser", Phys. Rev. Lett.45, 1486 (1980) CrossRef J. Martin-Regalado et al., "Polarization switching in vertical-cavity surface emitting lasers observed at constant active region temperature", Appl. Phys. Lett. 70, 3350 (1997) CrossRef M. B. Willemsen et al., "Polarization Switching of a Vertical-Cavity Semiconductor Laser as a Kramers Hopping Problem", Phys. Rev. Lett. 82, 4815 (1999) CrossRef M. B. Willemsen et al., "Anatomy of a Polarization Switch of a Vertical-Cavity Semiconductor Laser", Phys. Rev. Lett. 84, 4337 (2000) CrossRef T. Mukaihara et al., "Excess intensity noise originated from polarization fluctuation in vertical-cavity surface-emitting lasers", IEEE Photon. Technol. Lett. 7, 1113 (1995) CrossRef

Vertical Cavity Surface Emitting Lasers (VCSELs) with isotropic optical feedback are studied especially in the so-called low frequency fluctuations regime. Correlation properties between linear polarizations are analyzed both analytically and numerically. The RF spectrum shows a double peak structure close to the external cavity frequency which can be predicted by our adapted Spin-Flip Model (SFM). We provide here numerical evidence of the interplay between modes and anti- modes which are solutions of the stability analysis of the VCSEL with feedback and demonstrate that this interplay is responsible for the double peak structure.

The laser's threshold properties gradually evolve from the macroscopic to the nanoscopic scale through the mesoscale, whose best examples are the Vertical Cavity Surface Emitting Lasers (VCSELs). We show how the latter contribute to the understanding of the evolution of laser physics as the cavity volume is reduced thanks to favourable conditions: sufficient photon flux for a complete characterization with current instrumentation, coupled to physical characteristics which already approach those of nanodevices. A further reduction in cavity volume is nowadays possible in VCSELs, bringing within reach the nanoscale on the basis of mature technology. This will speed up both the fundamental investigations on the physics of nanolasers and open up the field for shorter-term applications in terms of nanosources- e.g., for optical chips- thanks to the possibility of coupling the VCSEL output into waveguides. Finally, we present an overview of results we have obtained on the physical characterization of the lasing transition in currently available, electrically-pumped VCSEL devices.