Semi-automatic true orthophoto production by using LIDAR data

The detailed representation of the topography is an important aspect when dealing with any flood simulation model. A Digital Surface Model (DSM) with fine spatial resolution can capture topographic object boundaries with a high level of detail. Light detection and ranging (LiDAR) is a technology that can rapidly collect elevation data of a relatively large topographic area with fine spatial resolution (< 0.5m ∼1m). Information about physical objects on the DSM is critical for storm water management as the propagation of flood water is influenced by both the terrain and the objects on the terrain. The processing of LiDAR data is an important task for generating an accurate DSM suitable to running a flood simulation model. Filtering is the first step in processing LiDAR data. In the LiDAR community, the term “filtering” means the task of separating LiDAR data into ground (bare earth) and non-ground points (buildings and trees). However, the choice of appropriate filtering algorithm is crucial in order to detect micro objects such as boundary walls, fences, and thin embankments that have significant impact on the surface flow pattern. This study offers an innovative approach for developing a LiDAR filtering algorithm that is flexible in nature and able to detect not only buildings and trees but also the micro objects. The filtering algorithm is applied to two study areas, and the output suggests close correspondence to reality.

ABSTRACTLandslides are a pervasive natural disaster, resulting in severe social, environmental and economic impacts worldwide. The tropical, mountainous landscape in South-West Mexico is predisposed to landslides because of frequent hurricanes and earthquakes. The main goal of this study is to compare landslide susceptibility maps in Guerrero derived using high-resolution LIDAR (light detection and ranging) data from both a manual landslide event inventory and an automated landslide inventorying algorithm. The paper also highlights the importance of applying LIDAR data in landslide inventorying and susceptibility mapping.We mapped landslides based on two approaches: (1) manual mapping using satellite images and (2) automatic identification of landslide morphology employing the Contour Connection Method (CCM). We produced a landslide susceptibility map by computing the probability of landslide occurrence from statistical relationships of inventoried landslides detected with LIDAR digital terrain models (DTMs) and derived landslide-causing factors using the logistic regression method.Our results suggest that the automated inventory derived through the CCM algorithm with LIDAR DTMs effectively minimizes the time-consuming and subjective manual inventorying process. The high overall prediction accuracy (up to 0.83) from logistic regression demonstrates the validity and applicability deriving reliable landslide susceptibility maps from an automated inventory; however, LIDAR data are required.

Civil engineering includes a wide range of applications that require three-dimensional (3D) information. With the advent of LiDAR (Light Detection And Ranging) technology, obtaining 3D terrain information accurately in a cost and time effective manner became more popular. In this paper, three case studies demonstrate the roles and applications of airborne LiDAR data including highway, transmission line and hydropower dam development projects. In first case study, the highway alignment was considerably changed after the initial design stage. LiDAR data was able to do the re-alignment survey quickly, allowing for prompt changes in design. In the next case study, a comparison is made between conventional transmission route alignment design and the design using PLS-CADD with LiDAR data. Utilizing the LiDAR data in PLSCADD allows transmission line engineers to model the construction costs of several alignments options effectively and efficiently compared to the conventional method. The last case study uses LiDAR for obtaining the necessary information for proposed dam. Using LiDAR data maximizes topological accuracy and volume measurements while minimizing survey time and costs. Furthermore, utilizing the multi-temporal LiDAR data can reveal valuable information such as topography changes. LiDAR survey technology has proven that it is the best method to capture accurate data from the earth surface which provides maximum density of topographical &amp; digital imagery information for various applications.

Digital elevation models (DEMs) resulting from LIDAR (light detection and ranging) surveys are now more available in the hydrology and hydraulics (H&H) community, not only for hydraulic applications in small areas close to river networks but also for hydrologic applications in whole basins. Several questions arise when trying to combine LIDAR data and hydrologic models. Despite the long processing time, LIDAR-derived DEMs can provide more accurate information that is useful for basin hydrogeomorphic characterization, in comparison with DEMs at resolutions commonly used in hydrologic applications (cell size 20-30 m). Of particular focus here are river network properties and the instantaneous unit hydrograph (IUH) framework. Two case studies, one in Italy and the other in the USA, are presented in which three DEMs are analyzed with differing resolutions as follows: "standard," i.e., a resolution commonly used in hydrologic applications (cell size 20-30 m), LIDAR (cell size 1-2.5 m), and LIDAR-resampled at the same resolution as the "standard" DEM. Results suggest that the higher spatial resolution LIDAR-derived data are preferable and can introduce more detailed information about basin hydrogeomorphic behavior.

Exploring LiDAR data for mapping the micro-topography and tidal hydro-dynamics of mangrove systems: An example from southeast Queensland, Australia

Light Detection and Ranging (LiDAR) is a technology that has been used for years with the variety of applications including the production of digital terrain models (DTMs), and high-accuracy mapping. LiDAR offers a very detailed collection of 3-D point clouds of the earth surface which can be used in generating orthophotos. Traditional orthophoto production based on the DTM has to accept that buildings and other objects above ground are not correctly placed in the orthophoto. These deficiencies can be overcome by simply taking the digital surface model (DSM) into account. In this paper, the literature reviews on the quality of true orthophoto production by fusing the digital aerial photos and LiDAR DSM done by former researchers are investigated. The results of the true orthophoto will be assessed by comparing the output and achievement gained by the researchers on the same field of study.

Foresters are increasingly interested in remote sensing data because they provide an overview of landscape conditions, which is impractical with field sample data alone. Light Detection and Ranging (LiDAR) provides exceptional spatial detail of forest structure, but difficulties in processing LiDAR data have limited their application beyond the research community. Another obstacle to operational use of LiDAR data has been the high cost of data collection. Our objectives in this study were to summarize, at the stand level, both LiDAR- and Landsat (satellite)-based predictions of some common structural and volume attributes and to compare the cost of obtaining such summaries with those obtained through traditional stand exams. We found that the accuracy and cost of a LiDAR-based inventory summarized at the stand level was comparable to traditional stand exams for structural attributes. However, the LiDAR data were able to provide information across a much larger area than the stand exams alone.

Airborne light detection and ranging (LIDAR) system uses in many field such as military, agriculture, geology and transportation. LIDAR data acquisition consumes several gigabytes from the storage capacity of the system. So, it's necessary to reduce the on board storage capacity as well as its transmission rate. Compression of LIDAR data means reducing the amount of data required to represent the digital data acquired by LIDAR system. This is done by removing data redundancies to achieve compression. In this paper we explain LIDAR system theory and component, compare between lossy and lossless compression techniques then we discuss LIDAR data compression techniques in order to choose a suitable one for LIDAR system that gives high compression ratio with suitable processing time. In most LIDAR data compression techniques classification of LIDAR data is an important issue as a preprocessing step to simplify the data. Using more than one compression algorithms increase the compression ratio but increase the processing time as well.

Automated feature extraction based on prototypes is only partially successful when applied to remotely sensed imagery of natural scenes due to the complexity and unpredictability of the shape and geometry of natural features. Here, a new method is developed for extracting the locations of treetops by applying GIS (Geographical Information System) overlay techniques and morphological functions to high spatial resolution airborne imagery. This method is based on the geometrical and spatial properties of tree crowns. Airborne data of the study site in the New Forest, UK included colour aerial photographs, LIDAR (Light Detection And Ranging) and ATM (Airborne Thematic Mapper) imagery. A DEM (Digital Elevation Model) was generated from LIDAR data and then subtracted from the original LIDAR image to create a Canopy Height Model (CHM). A set of procedures using image contouring and the manipulation of the resulting polygons was implemented to extract treetops from the aerial photographs and the CHM. Criteria were developed and threshold values were set using a supervised approach for the acceptance or rejection of features based on field knowledge. Tree species were mapped by classifying the ATM data and these data were co‐registered with the treetop layer. For broadleaved deciduous plantations the success of treetop extraction using aerial photographs was 91%, but was much lower using LIDAR data. For semi‐natural forests, the LIDAR produced better results than the aerial photographs with a success of 80%, which was considered high, given the complexity of these uneven aged stands. The methodology presented here is easy to apply as it is implemented within a GIS and the final product is an accurate map with information about the location, height and species of each tree.

With the increasing number of remote sensing (RS) data sources, the joint utilization of multimodal data in Earth observation tasks has become a crucial research topic. As a typical representative of RS data, hyperspectral images (HSIs) provide accurate spectral information, while rich elevation information can be obtained from light detection and ranging (LiDAR) data. However, due to the significant differences in multimodal heterogeneous features, how to efficiently fuse HSI and LiDAR data remains one of the challenges faced by existing research. In addition, the edge contour information of images is not fully considered by existing methods, which can easily lead to performance bottlenecks. Thus, a joint classification network of HSI and LiDAR data based on Mamba (HLMamba) is proposed. Specifically, a gradient joint algorithm (GJA) is first performed on LiDAR data to obtain the edge contour data of the land distribution. Subsequently, a multimodal feature extraction module (MFEM) was proposed to capture the semantic features of HSI, LiDAR, and edge contour data. Then, to efficiently fuse multimodal features, a novel deep learning (DL) framework called Mamba, was introduced, and a multimodal Mamba fusion module (MMFM) was constructed. By efficiently modeling the long-distance dependencies of multimodal sequences, the MMFM can better explore the internal features of multimodal data and the interrelationships between modalities, thereby enhancing fusion performance. Finally, to validate the effectiveness of HLMamba, a series of experiments were conducted on three common HSI and LiDAR datasets. The results indicate that HLMamba has superior classification performance compared to other state-of-the-art DL methods. The source code of the proposed method will be available publicly at <uri xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">https://github.com/Dilingliao/HLMamba</uri>.

Good forest management requires comprehensive and reliable inventory data spanning large areas. Forest management has increasingly relied on remote sensing, specifically light detection and ranging (LiDAR). However, due to the high costs associated with data collection and processing, wall-to-wall LiDAR data is rarely obtained for forests. In contrast, multispectral imagery from optical sensors often covers large extents but they fail to capture detail below the forest canopy and do not directly measure structural attributes. To take advantage of the complementary benefits of different sensors, active LiDAR and passive optical sensors have been combined and applied to problem-solving in a forestry context for over a decade. A review of the literature shows that fusion of different sensors has resulted in superior performance relative to individual sensors for classifying and delineating forest areas (up to 20 % accuracy improvement), identifying species (up to 21 % accuracy improvement), and estimating forest volume and biomass (up to 55 % accuracy improvement). In contrast, sensor fusion achieved only minor improvements for tree or forest height estimation (1–7 % accuracy improvement); this is likely because LiDAR alone is already so effective. This review was unable to draw conclusions on the performance of sensor fusion for forest age and productivity assessment due to the limited number of studies. The lack of results in these areas presents an opportunity for future research. The literature clearly demonstrates the utility of integrating LiDAR and optical data for many aspects of forest description. Perhaps the greatest challenge moving forward will be to operationalise the research such that forestry companies and governments can take advantage of the benefits of data fusion.

Automatically extracting land use information from remotely sensed imagery is an active yet challenging topic. As the urban unit that is related most closely to the spatial distribution of population, the buildings for residential land uses are of special interests for broad applications. This paper presents a three-step approach to identify residential buildings using light detection and ranging (LiDAR) data, aerial photographs, and road maps. A multidirectional ground-ltering algorithm rst separates ground from LiDAR data to produce a digital surface model, a digital terrain model, and the height of objects above ground. Then, a morphology-based buildingdetection method extracts buildings by gradually removing other objects (especially trees) based on the difference in the rst and last returns of LiDAR data, building height, vegetation indexes from aerial photograph, and the morphological characteristics of building footprints. Finally, residential buildings are separated through the classication based on seven land use indicators: area, height and compactness of buildings, the distance to major roads, the percentage of green space and parking space surrounding a building, and building density within a block. The method was tested in an area in Austin, Texas. The results showed that the method successfullyCONTENTS7.1 Introduction ................................................................................. 170 7.2 An object-oriented approach to identify residential buildingsfrom LiDAR and aerial photographs ............................................ 171 7.2.1 Multidirectional ground ltering from LiDAR data .......... 172 7.2.2 Morphology-based building detection .............................. 174 7.2.3 Object-oriented building land use classication ................. 1767.3 Method validations and performance ........................................... 180 7.4 Conclusion .................................................................................... 180 Acknowledgments ................................................................................. 182 References ............................................................................................. 182extracted buildings from LiDAR and aerial photographs and identied 81.1% of the residential buildings.

Airborne Laser scanning systems with light detection and ranging (LIDAR) technology is one of the fast and accurate 3D point data acquisition techniques. Generating accurate digital terrain and/or surface models (DTM/DSM) is the main application of collecting LIDAR range data. The LIDAR technique facilitates the rapid production of models which contain ground and above surface objects in 3D (Jaafar et al., 1999). Today automatic / semi-automatic generation of 3D digital building models and other city furniture from LIDAR data is a very active area of scientific research (Elaksher and Bethel, 2002) indicates that manual surface reconstruction is very costly and time consuming, and the development of automated algorithms is of great importance. Currently with this LIDAR data in place, it is possible to derive models and information (e.g. the heights of the buildings).This paper focuses on and explains our efforts on automatically checking Buildings’ Zoning Regulation Compliance by integrating geometric information derived from 3D LIDAR data and semantic information acquired from 2D Implementation Development Maps

Hyperspectral image classification has been an active topic of research. In recent years, it has been found that light detection and ranging (LiDAR) data provide a source of complementary information that can greatly assist in the classification of hyperspectral data, in particular when it is difficult to separate complex classes. This is because, in addition to the spatial and the spectral information provided by hyperspectral data, LiDAR can provide very valuable information about the height of the surveyed area that can help with the discrimination of classes and their separability. In the past, several efforts have been investigated for fusion of hyperspectral and LiDAR data, with some efforts driven by the morphological information that can be derived from both data sources. However, a main challenge for the learning approaches is how to exploit the information coming from multiple features. Specifically, it has been found that simple concatenation or stacking of features such as morphological attribute profiles (APs) may contain redundant information. In addition, a significant increase in the number of features may lead to very high-dimensional input features. This is in contrast with the limited number of training samples often available in remote-sensing applications, which may lead to the Hughes effect. In this work, we develop a new efficient strategy for fusion and classification of hyperspectral and LiDAR data. Our approach has been designed to integrate multiple types of features extracted from these data. An important characteristic of the presented approach is that it does not require any regularization parameters, so that different types of features can be efficiently exploited and integrated in a collaborative and flexible way. Our experimental results, conducted using a hyperspectral image and a LiDAR-derived digital surface model (DSM) collected over the University of Houston campus and the neighboring urban area, indicate that the proposed framework for multiple feature learning provides state-of-the-art classification results.

Improving classification accuracy of airborne LiDAR intensity data by geometric calibration and radiometric correction