Signal Interference between GPS and Wide Area Augmentation System

In urban road environments, global navigation satellite system (GNSS) signals may be interrupted due to occlusion by buildings and obstacles, resulting in reduced accuracy and discontinuity of combined GNSS/inertial navigation system (INS) positioning. Improving the accuracy and robustness of combined GNSS/INS positioning systems for land vehicles in the presence of GNSS interruptions is a challenging task. The main objective of this paper is to develop a method for predicting GNSS information during GNSS outages based on a long short-term memory (LSTM) neural network to assist in factor graph-based combined GNSS/INS localization, which can provide a reliable combined localization solution during GNSS signal outages. In an environment with good GNSS signals, a factor graph fusion algorithm is used for data fusion of the combined positioning system, and an LSTM neural network prediction model is trained, and model parameters are determined using the INS velocity, inertial measurement unit (IMU) output, and GNSS position incremental data. In an environment with interrupted GNSS signals, the LSTM model is used to predict the GNSS positional increments and generate the pseudo-GNSS information and the solved results of INS for combined localization. In order to verify the performance and effectiveness of the proposed method, we conducted real-world road test experiments on land vehicles installed with GNSS receivers and inertial sensors. The experimental results show that, compared with the traditional combined GNSS/INS factor graph localization method, the proposed method can provide more accurate and robust localization results even in environments with frequent GNSS signal loss.

A sparse global navigation satellite system (GLONASS) signal acquisition method based on compressive sensing and multiple measurement vectors is proposed. The nonsparse GLONASS signal can be represented sparsely on our proposed dictionary which is designed based on the signal feature. Then, the GLONASS signal is sensed by a normalized orthogonal random matrix and acquired by the improved multiple measurement vectors acquisition algorithm. There are 10 cycles of pseudorandom codes in a navigation message, and these 10 pseudorandom codes have the same row sparse structure. So, the acquisition probability can be raised by row sparse features theoretically. A large number of simulated GLONASS signal experiments show that the acquisition probability increases with the increase in the measurement vector column dimension. Finally, the practical availability of the new method is verified by acquisition experiments with the real record GLONASS signal. The new method can reduce the storage space and energy loss of data transmission. We hope that the new method can be applied to field receivers that need to record and transmit navigation data for a long time.

The traditional measurement of signal bandwidth using single-carrier frequency sweeping is not suitable for global navigation satellite system (GNSS) signal. A new analysis technique of signal bandwidth with digital signal processing technique has been developed. After the GNSS signal is highly sampled, the spectrum of the actual GNSS signal and the ideal signal generated locally are evaluated in digital domain. The bandwidth of GNSS signal can be calculated. Simulation has been done for the proposed measurement technique using spectrum evaluation algorithm of the Periodogram and the Welch respectively. The simulation results shows that the GNSS signal bandwidth can be accurately estimated after the ideal and actual signal spectrum are evaluated and calculated using the Welch. The simulation results show that The estimating accurate of signal bandwidth can be higher than 99.9% in the case of the proper parameters have been set for Welch.

People have to move between indoor and outdoor frequently in city scenarios. The global navigation satellite system signal cannot provide reliable indoor positioning services. To solve the problem, this article proposes a seamless positioning system based on an inverse global navigation satellite system signal, which can extend the global navigation satellite system service into the indoor scenario. In this method, a signal source is arranged at a key position in the room, and the inverse global navigation satellite system signal is transmitted to the global navigation satellite system receiver to obtain a preset positioning result. The indoor positioning service is continued with the inertial navigation system after leaving the key position. The inverse global navigation satellite system seamless positioning system proposed in this article can unify indoor and outdoor positioning using the same receiver. The receiver does not need to re-receive navigation information when the scene changes, which avoids the switching process. Through the design of signal layer coverage, the receiver is in a warm start state, and the users can quickly fix the position when the scenario changes, realizing quick access in a true sense. This enables the ordinary commercial global navigation satellite system receiver to obtain indoor positioning capability without modification, and the algorithm can perform accurate positioning indoors and outdoors without switching.

The Global Navigation Satellite System (GNSS) signals are often blocked or interfered in complex geographical or electromagnetic environments, which may make GNSS receivers unable to provide satisfying navigation and positioning services. There have been many ground-based or space-based GNSS augmentation systems to improve the resilience of GNSS positioning, of which most of them rely on additional infrastructures. In this study, a smartphone-based tightly-coupled positioning method was developed using the images from a build-in monocular camera and GNSS signals. In this method, the feature points with the known coordinates are regarded as 'visual pseudolite' and the distance between the camera and the feature points was calculated according to the photogrammetry approaches and used to estimate the user positioning with GNSS signals. The experimental results showed the feasibility of the tightly-coupled positioning algorithm and reached the positioning accuracy of ±5.56 m (1?), which is significantly higher than that of GNSS-only and vision-only positioning solutions.

Implementing the International GNSS Service 2021+ Strategic Plan: Vision and Use Cases

Due to the low signal power, the Global Navigation Satellite System (GNSS) signal is vulnerable to interference and even cannot be captured or tracked in harsh environments. As an alternative, the Low Earth Orbit (LEO) satellite has been widely used in the navigation field due to the advantages of low cost and strong signals. It is becoming a significant component of the new combined navigation system with GNSS. The combination of an LEO Doppler signal and GNSS observables can improve the positioning accuracy and high-precision positioning convergence time of the GNSS receiver. However, the GNSS signal receiving capability cannot be improved from this data fusion level. We propose a novel assisted structure where GNSS signal acquisition and Doppler tracking are assisted by LEO Doppler positioning. The receiver uses the LEO signal to achieve Doppler positioning firstly. Then, the coarse position with the GNSS navigation messages received from LEO, as well as the estimated clock information, is used to assist in the acquisition and tracking of GNSS. In this way, the GNSS receiver’s sensitivity can get the benefit from this integrated system. The paper presents the structure of the assisted receiver and analyzes the assisted GNSS signal acquisition and carrier tracking performance in detail. Simulation experiments of this assisted structure are carried out to verify its superiority of acquisition and tracking sensitivity in comparison with standalone GNSS receivers. Theoretical analysis and experimental results show that the proposed acquisition method can achieve 90% detection probability at a carrier-to-noise ratio (C/N0) of 15 dB-Hz, which is about 8 dB higher than the conventional acquisition method without assistance; the proposed tracking method can track weak signals of 5 dB-Hz, which is about 4 dB higher than the conventional method. Therefore, this novel LEO-assisted receiver has significantly improved weak signal acquisition and tracking sensitivity.

The study of climate change is an important field of research. Monitoring of atmospheric variability especially the tropospheric precipitable water vapor (PWV) is a powerful way to investigate climate change. Global navigation satellite systems (GNSS) provide a good tool for studying atmospheric parameters as GNSS signals along its path from the satellites to the ground based receivers suffer a significant delay due to the refractivity of earth’s atmosphere. GNSS signals are not only delayed but also refracted in the neutral atmosphere. The zenith wet delays (ZWD) caused by the troposphere can be estimated during the geodetic processing of GNSS signals. Since the ZWD is tightly correlated to the PWV, GNSS observations can be used to study the changes of PWV. In this study GNSS data from the Egyptian permanent GNSS network (EPGN), International GNSS Service (IGS), EUREF Permanent Network (EPN) and Scripps Orbit and Permanent Array Center (SOPAC), for the years 2013 and 2014, were used. These GNSS stations provided a good geometrical coverage over the respective region. All GNSS data were processed using Bernese V 5.2 software. The needed product from GNSS data processing is the tropospheric zenith total delay (ZTD) over each GNSS site. The ZTD is divided based on physical parameters into zenith hydrostatic delay (ZHD) and zenith wet delay (ZWD). The ZWD is the basic observable used to calculate PWV. The values of the PWV were calculated and its variation over the study area was investigated. The quality of calculated PWV values from GNSS data evaluated against traditional Radiosonde (RS) measurements. The results of GNSS PWV showed good agreement with RS PWV when the PWV values were low, but this agreement became worse at high PWV values as the differences between the two techniques increased. The correlation coefficient between RS PWV and GNSS PWV varied from 0.31 to 0.84. Standard deviation of the differences between RS PWV and GNSS PWV ranged from 2.369 to 5.973 mm. The PWV estimated from GNSS observations had annual cycle, and its cycle in 2013 was different from that in 2014. The PWV differences between the 2 years clarified that the water vapor content over the east Mediterranean in most of 2014 days was higher than that in 2013. Furthermore, PWV variations were noted on both temporal and spatial scales. The highest temporal variation value was 25.41 mm whereas the maximum value of the spatial variation was 19.67 mm. The present study illustrated the importance of using geodetic networks to provide atmospheric information.

It is well known that the presence of unintentional or intentional Radio Frequency Interference (RFI) signals in the Global Navigation Satellite Systems (GNSS) frequency bands can cause severe positioning performance degradation and even a complete service unavailability. Moreover, with the development of Software Defined Radio (SDR) GNSS signal generators and the popularization of low-cost SDR front-ends, the spoofing of the GNSS civil service turns out to be a real threat for GNSS receivers. Complementary to time and frequency-domain mit-igation techniques, antenna-array based receivers can benefit from spatial domain processing. An antenna array receiver can also discriminate between legitimate GNSS signals from these being broadcasted by the spoofer. In this work, we present an evolution of a receiver-independent GNSS smart antenna architecture for a real-time, automatic and autonomous, simultaneous anti-jamming and anti-spoofing spatial filtering for GNSS bands. The novel spoofer detection and mitigation algorithm is able to detect the spoofer and protect the receiver even in a scenario where the spoofer is transmitted in combination with a strong jammer to force the receiver to lose the legitimate GNSS signal lock. A prototype is also presented, implemented using Commercial Off The Shelf (COTS) components. The proposed smart antenna can be connected to any conventional single-antenna GNSS receiver. The paper includes both the theory of operation, the implementation details and its performance analysis in an extended measurement campaign.

The global navigation satellite system (GNSS) signal modulation type plays a crucial role in determining the performances of positioning, navigation and timing (PNT) services. Currently, the binary offset carrier (BOC) modulation signal and binary coded symbol (BCS) modulation signal are both bipolar signals, which greatly restrict the room of improving the GNSS signal performance. Therefore, multi-level coded symbol (MCS) modulation has received great attention in the field of GNSS signal design. The MCS modulation is the most extensive step-coded symbol modulation mode, where BOC modulation and BCS modulation are its special cases. Since the waveform symbol of the MCS modulation signal can be arbitrarily valued, the optimal GNSS signal can be designed. However, like the BOC modulation signal, the MCS modulation signal also has the problem of ambiguous tracking, and then results in a large pseudo range measurement error, which is unacceptable for the new generation GNSS with high accuracy. In recent years, the unambiguous tracking of GNSS signals has become a hot research subject in the navigation signal processing domain and many methods are presented, and those methods can be divided into three categories:BPSK-like method, bump jump (BJ) method, and side-peak cancellation (SC) method. However, these methods are designed for BOC signal, and they are not suitable for MCS signal. Therefore, in this paper we propose a general unambiguous tracking algorithm based on the pseudo correlation function (PCF), which is suitable for MCS modulated signals. Firstly, the unitary expression of MCS modulated signal based on waveform value vector is given, then the unitary formula of cross-correlation function for MCS signal is derived and the definition of PCF is given. Then the constraint condition which should be satisfied to realize unambiguous tracking is analyzed in depth, and the universal constructing method of two reference signals and the relationship between each other are derived according to this constraint condition, which brings great convenience for solving the specific MCS signal. The code tracking loop model of GNSS receiver based on the proposed method is illustrated. It is observed that the proposed method can receive different MCS signals under the same receiver loop framework, and can simplify the design of the receiver while eliminating the tracking ambiguous problem. Finally, as a special case of MCS signal, the applications of the proposed method in four kinds of BOC signals are discussed respectively, and then the waveform value vector of the reference signal and the unitary expression of code discriminator are derived. Simulation results show that the proposed method can effectively solve the ambiguous tracking problem of MCS signal, which has good performance and broad application prospect.

The reflected GNSS signals at the L-band is significantly advantageous in soil moisture monitoring as they are sensitive to the dielectric properties determined by the volumetric water content of topsoil, and they can penetrate vegetation, except in very dense forests. The Global Navigation satellite system Occultation Sounder (GNOS-II) with a reflectometry technique onboard the Fengyun-3E (FY-3E) satellite, launched on 5 July 2021, is the first mission that can receive reflected Global Navigation Satellite System (GNSS) signals from GPS, BeiDou and Galileo systems. This paper presents the soil moisture retrieval results from the FY-3E GNOS-II mission using 16 months of data. In this study, the reflectivity observations from different GNSS systems were firstly intercalibrated with some differences analyzed. Observations were also corrected by considering vegetation attenuation for 16 different land cover classifications. Finally, an empirical model was constructed for volumetric soil moisture (VSM) estimation, where the reflectivity of GNOS-II was linearly related to the SMAP reference soil moisture for each 36 km ease grid. The overall root-mean-square error of the retrieved soil moisture is 0.049 compared with the SMAP product, and 0.054 compared with the in situ data. The results of the three GNSS systems show similar levels of accuracy. This paper, for the first time, demonstrates the feasibility of global soil moisture retrieval using multiple GNSS signals.

With the ever-increasing number of small satellites launched into space, on-board orbit determination is becoming more and more important. Precise satellite positions are needed for constellation maintenance, formation flying, communication optimization, collision avoidance and Earth observation. In addition, accurate time information is required for the functioning of the instruments on board. Low-cost off-the-shelf Global Navigation Satellite System (GNSS) receivers and antennas, adapted to the small size and weight of the satellite, allow precise on-board orbit determination and time synchronization for even the smallest satellites.We analysed more than one year of on-board navigation solutions (NAVSOL) from 8 Astrocast CubeSats, which are equipped with our multi-GNSS single-frequency payload. Based on the residuals from a dynamic orbit fitting, we found that the quality of the NAVSOL from the Astrocast satellites varies strongly both over time and between satellites, with an RMS ranging from a few meters to several tens of meters.In this study, we focus on three main effects that influence the quality of the NAVSOL from the Astrocast satellites: (1) The orbit-fit residuals show a positive radial offset in the range of about 6 m to 15 m, which is caused by ionospheric refraction. Our data show that GNSS signals at negative elevations are very strongly affected by the ionospheric refraction and thus account for the major part of the radial offset. (2) Discrepancies between the NAVSOL positions and velocities, and simulations with a GNSS signal generator show a once-per-revolution periodicity in the out-of-plane component, with amplitudes of 2 m and 5 cm/s in position and velocity, respectively. This effect is probably due to an inappropriate dynamic model used in the real-time navigation algorithm of the GNSS receiver. (3) Depending on the location of the GNSS antenna on board the satellite, the noise level varies by a multiple. This is assumed to be due to the antenna orientations, interference of the GNSS signals with electromagnetic waves coming from the satellite platform, signal attenuation during the transmission from the antenna to the receiver and differences in the soldering or tuning of the individual GNSS antennas.These findings help us refine hardware configurations and firmware settings in preparation for future Astrocast satellites or other nanosatellite missions. By eliminating or minimizing the mentioned effects, we expect to consistently achieve an accuracy on the level of a few meters for the real-time navigation solution of commercial off-the-shelf single-frequency GNSS receivers in space.

This paper presents one of the solutions to the problem of multipath propagation and effects on Global Navigation Satellite Systems (GNSS) signals in urban canyons. GNSS signals may reach a receiver not only through Line-of-Sight (LOS) paths, but they are often blocked, reflected or diffracted from tall buildings, leading to unmodelled GNSS errors in position estimation. Therefore in order to detect and mitigate the impact of multipath, a new ray-tracing model for simulation of GNSS signals reception in urban canyons is proposed - based on digital 3D maps information, known positions of GNSS satellites and an assumed position of a receiver. The model is established and validated using experimental, as well as real data. It is specially designed for complex environments and situations where positioning with highest accuracy is required - a typical example is navigation for blind people.

Ground-based GNSS ZTD/IWV estimation system for numerical weather prediction in challenging weather conditions

Detecting and processing Global Navigation Satellite System (GNSS) signals indoors and in urban canyons, have gained a great deal of attention due to the problems of very weak signals and hostile environments. The detection of GNSS signals is generally based on the application of a statistical test, derived from the maximum likelihood theory. The work presented here considers a new approach to the detection of weak GNSS signals using a Bayesian technique within a scenario where the search space size is already reduced to a few tens of cells using some kind of assisted information. The search space cells are considered as candidate cells, where each candidate cell is associated with a code delay and a Doppler frequency. For each candidate cell, a posteriori probability is propagated for a fixed number of operation cycles. At the end of the process, the maximum a posterior (MAP) criterion is used to select the correct cell. Simulation results are presented indicating that the proposed method provides a significant performance advantage over other reference schemes. They include a noncoherent integration scheme and another scheme which also utilizes the posterior probabilities as decision statistics but differs in the mechanism of probability propagation.