Simple design approach for asymmetric resonant inductive coupled WPT systems using J-inverters

It is well known that the power transfer efficiency (PTE) of a two-coil wireless power transfer (WPT) system is maximized at critical coupling under fixed system parameters. However, the two-coil WPT system is critical-coupled with a relatively short distance between the coils. To overcome the problem, a multicoil WPT system has been studied. In this paper, we review the impedance characteristics of the critical-coupled two-coil WPT system and reveal that the conventional three-coil WPT system cannot have the same impedance characteristics as critical coupling. Based on the impedance matching conditions with critical coupling of the two-coil WPT system, we propose a design method of a three-coil WPT system in which the free resonant frequencies of all resonators are changed. The proposed design method is successfully implemented at the operating frequency of 6.78 MHz. The experimental results are in good agreement with the simulated PTEs and show that by changing the free resonant frequencies, a higher PTE can be effectively achieved in comparison to the conventional two-coil and thee-coil WPT systems.

This paper presents a novel design concept for near-field wireless power transfer (WPT) systems that leverages the seamless integration of metamaterials (MTMs) into slotted resonators. This approach enhances magnetic field ( $$\textbf{B}$$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mi>B</mml:mi> </mml:math> ) distribution, strengthens evanescent wave coupling, and hence improves overall WPT performance. An MTM structure exhibiting negative permeability at the operating frequency of 433 MHz was designed and incorporated into a square-slot-based resonator. Electromagnetic (EM) analysis revealed increased current density and subsequently enlarged $$\textbf{B}$$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mi>B</mml:mi> </mml:math> around the resonator. Additionally, impedance matching, key parameter extraction, and equivalent circuit (EC) modeling were performed using the effective J-inverter method. The developed WPT system, with compact dimensions of 30 $$\times$$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mo>×</mml:mo> </mml:math> 30 $$^{\text {2}}$$ <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML"> <mml:mmultiscripts> <mml:mrow/> <mml:mrow/> <mml:mtext>2</mml:mtext> </mml:mmultiscripts> </mml:math> , achieved a power transfer efficiency of 82% at 33 mm. The design was experimentally validated, showing excellent agreement among EM simulations, EC modeling, and measurement results. Finally, performance comparison with other reported systems confirmed the superiority and practical effectiveness of the proposed design in enabling compact and highly efficient WPT systems.

The magnetic fields (MF) generated in close proximity to high power wireless power transfer (WPT) systems generally exceed exposure limits and might also violate basic restrictions (BR). However, there are as yet no available standards describing methods to measure the MF generated by WPT systems. In this study, a new method for demonstration of compliance with the BR in the close proximity to sources at frequencies from 3 kHz to 10 MHz is proposed. This approach mitigates overestimation by incident field assessment in strong field gradients close to WPT systems. The spatial peak MF amplitude and gradient generated by WPT systems are measured with a field gradient probe at the closest location to the source. The induced fields and absorbed power are then calculated on the basis of specific transformation functions for testing of compliance with the BR of all international safety guidelines.

A wireless power transfer (WPT) system via magnetic resonance coupling method is attracting attention to high convenience. A WPT system has problems such as power transmitting loss and output voltage fluctuation due to the change in the coupling coefficient and the load state. In previous method, sliding mode control system as a tracking controller considering nonlinearity and uncertainty has been proposed, but the output of this control system had bias and chattering. This paper proposes operator-based nonlinear sliding mode control system to reduce chattering and bias simultaneously for a WPT system using buck converter. First, the model of the WPT system using rectifier and buck converter is explained and dynamics formulas are derived. Next, the proposed operator-based nonlinear sliding mode control system design for the WPT system is described and tracking performance is confirmed. Finally, the result of simulation of constant voltage control and comparison with the previous method is shown.

Polyphase wireless power transfer (WPT) systems can achieve much higher surface power densities (kW/m<sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup>) and specific power levels (kW/kg) compared to the conventional circular single phase WPT systems. Therefore, polyphase WPT systems can reduce the size, weight, volume, and cost of the WPT systems and can simplify the electric vehicle integration with less demand for space. This study presents the high-performance and compact 100-kW WPT development using polyphase electromagnetic coupling coils with rotating magnetic fields.

A Wireless Power Transfer (WPT) system, known for its contactless power delivery, is extensively used for power supply in spacecraft applications. Achieving efficient and stable power transfer necessitates the integration of DC/DC converters on both the primary and secondary sides of WPT systems for power conversion and control. Traditional efficiency optimization methods primarily focus on impedance matching within the wireless power resonance network, often neglecting the overall efficiency optimization of multi-stage DC-DC and WPT systems. This oversight results in suboptimal overall system efficiency despite optimal efficiency in the wireless transmission segment. Additionally, the time-varying nature of mutual inductance and load parameters during power transmission in WPT systems presents challenges for maximum efficiency tracking and power control. This paper introduces a multi-level coordinated control efficiency optimization method for WPT systems utilizing the particle swarm optimization (PSO) algorithm. This method takes into account the transmission losses across all power conversion units within the WPT system, establishing a mathematical model for the joint optimization of overall system transmission efficiency and power. The PSO algorithm is then employed to solve this optimization model using estimated mutual inductance and load values. By adjusting the DC/DC converters on both sides, the method ensures optimal overall system efficiency and consistent power transmission. Experimental results indicate that under varying load and mutual inductance conditions, a Series–Series (SS) compensated WPT system using this method achieves a 200 W power output with maximum efficiency tracking, a power output error of 0.63%, and an average transmission efficiency of 86.2%. This demonstrates superior power transmission stability and higher efficiency compared to traditional impedance matching methods.

ABSTRACTThis paper proposes a new method to increase the transfer efficiency of a wireless power transfer (WPT) system, having a source coil, a sprial transmitter (Tx) coil, a load coil and a ground plane, by utilizing the ground plane itself. The creation of cross slits at the ground center and employment of a lumped capacitor on the ground plane transform the ground plane into an additional resonator, which makes the original WPT system work as a 4‐coil WPT system, producing a higher efficiency. By experiment, with an optimized capacitor on the ground plane of C = 2180 pF, the measurement of transfer efficiency shows a maximum improvement of 10% at a transfer distance of 40 cm, compared to the case without the ground plane. The transfer efficiency of the proposed system at transfer distance of 15 cm is 46%. Circuit theory and electromagnetic simulations are employed to analyze the proposed WPT system, giving results consistent with the measured ones. The operating frequency of the proposed system is 6.78 MHz. © 2017 Wiley Periodicals, Inc. Microwave Opt Technol Lett 59:514–521, 2017

Many researches have been carried out by previous researchers to get better performance of a wireless power transfer (WPT) system. This research uses a partitioned shielding made of metallic material to protect WPT system from electromagnetic interference (EMI). Also, a shielding material is connected to ground, so that it can reduce occurrence of stray/parasitic capacitance between electrodes of electronic components. Both the electromagnetic interference and the stray/parasitic capacitance can deteriorate performance of WPT system. In this research, the WPT system works at voltage 14.7V, frequency 56,298 Hz, distance coil to coil is 0 till 5 cm. The efficiency of WPT system is achieved until 14.9 % (without shielding) and until 17.9% (with partitioned shielding).

A highly efficient wireless power transfer (WPT) system is required in many applications to replace the conventional wired system. The high temperature superconducting (HTS) wires are examined in a WPT system to increase the power-transfer efficiency (PTE) as compared with the conventional copper/Litz conductor. The HTS conductors are naturally can produce higher amount of magnetic field with high induced voltage to the receiving coil. Moreover, the WPT systems are prone to misalignment, which can cause sudden variation in the induced voltage and lead to rapid damage of the resonant capacitors connected in the circuit. Hence, the protection or elimination of resonant capacitor is required to increase the longevity of WPT system, but both the adoptions will operate the system in nonresonance mode. The absence of resonance phenomena in the WPT system will drastically reduce the PTE and correspondingly the future commercialization. This paper proposes an open bifilar spiral coils based self-resonant WPT method without using resonant capacitors at both the sides. The mathematical modeling and circuit simulation of the proposed system is performed by designing the transmitter coil using HTS wire and the receiver with copper coil. The three-dimensional modeling and finite element simulation of the proposed system is performed to analyze the current density at different coupling distances between the coil. Furthermore, the experimental results show the PTE of 49.8% under critical coupling with the resonant frequency of 25 kHz.

In previous researches, an operator-based sliding mode control design to achieve high power transfer efficiency of a wireless power transfer (WPT) system via magnetic resonance coupling were shown. However, it is difficult to reduce the steady-state error by using SMC-based tracking controller. In this paper, an operator-based integral sliding mode control method is adopted to reduce the steady-state error in the WPT system. Moreover, high power efficiency should be achieved in the WPT system by using an impedance matching control. The effectiveness of the proposed method is verified by simulation results.

The wireless power transfer (WPT) system based on parity-time (PT) symmetry has the advantages of robustness, stable, and efficient power transmission. However, the region of PT symmetry is limited, which cannot satisfy some practical requirements. Multiple transmitting coils have been shown to improve the misalignment tolerance of WPT systems. Towards this end, a parity-time-symmetric-based WPT (PT-based WPT) system with double-transmitting coil is presented in this article. First, an approximate equivalent circuit model of this PT-based WPT system was developed. Second, compared with the conventional single transmitting coil PT-based WPT system, the proposed system expands the PT symmetry region and provides higher output power and transmission efficiency. Furthermore, the mutual inductance between two transmitting coils can be designed to meet the requirements of different scenarios, which improves the freedom of system design. Finally, a 30 W prototype is designed to evaluate the proposed WPT system. Experimental results show that the critical coupling coefficient is reduced by about 12.5% at <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">k</i> <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">12</sub> = 0.51, which implies a longer transmission distance. Moreover, the maximum output voltage fluctuation in the strongly coupled region is only 3.5%, while the transfer efficiency is approximately constant, which implies stable and efficient power transfer.

An investigation of a resonant reactive shielding coil for wireless power transfer (WPT) systems is presented in this work. The shielding coil attenuates the magnetic field above and to the side of air-core WPT coils. A parameterized coil model is used to allow arbitrary circular winding geometry and current direction. Detailed modeling and mathematical calculations are provided, and an optimized design algorithm is proposed. The design method is validated using an experimental prototype shielding coil applied to a 3.03 MHz electric vehicle (EV) WPT system operating at 500 W output power. Experimental results show that the peak flux density on the top-center area of the coil is suppressed from 105 μT to 50 μT, and the magnetic field to the side of the vehicle is maintained well below the safety standard. In addition, effect of the shielding coil in WPT systems with metal and ferrite plates is investigated.

Analog-to-digital converter (ADC) is becoming of utmost importance in an automotive environment. With the increased number of magnetic field sources near the ADC that can alter its behaviors significantly, we need to model how magnetic field affects the performance of the ADC. Therefore, in order to accurately evaluate the practical performance of the ADC and the considerable off-chip and on-chip effects that are highly complex, the chip-printed circuit board (PCB) comodeling, cosimulation, and coanalysis are required. In this study, a comodel of the magnetic field effects on an ADC is proposed. The proposed comodel includes three separate submodels: a model of the magnetic field coupling from the wireless power transfer (WPT) system input to the PCB integrated with ADC, a model of the noise coupling from the PCB to the ADC input, and a model of the ADC behavior from the ADC input to the ADC outputs. Considering the magnetic field coupling from the magnetic field source to the PCB, a new inductive transmission line model (I-TLM) method is developed. This method achieves fast, precise, and broadband estimation of the magnetic field effects in comparison to previous estimation methods. To validate the proposed comodel, an ADC is fabricated using a 0.13-μm complementary metal-oxide semiconductor process and is wire-bonded to the designed PCB for ADC. A PCB-level WPT system is designed and built as the magnetic field source. The performance factor of the ADC is measured by sweeping the WPT system input frequency from 100 kHz to 1 GHz to find out the critical WPT system frequency for the designed ADC with the chip-PCB hierarchical structure. The results estimated by the proposed model correlate well with the full 3-D electromagnetic field simulation and measurement. The proposed modeling procedure reduces the time and computation resource in the design of the chip, package, and PCB to achieve high-quality analog devices or mixed-mode systems, while also providing an intuitive understanding of the radiated noise effect.

The wireless power transfer (WPT) system for LED TVs could be adapted to transfer power to specific locations in luxury residences. However, at a resonant frequency, the output power of the WPT system is only able to provide maximum power at only a set distance. This article presents the adaption of mutual impedance for maximum power point tracking (MPPT) to vary the distance for LED TVs using the WPT system. To adapt the mutual impedance, the frequencies and the resonator capacitances are tuned to the required distance. In the experiment, the WPT system was loaded with a 30W LED TV and the input was through a full-bridge inverter to enable the input voltage and frequency to be varied. The computer simulation and the actual experiment on MPPT for the LED TV WPT system closely correlate. The result shows that when the LED TV WPT system input was 6.66 V, 3.01 kHz, C 16.8 F, the maximum output power was 30.1 W was achieved at a distance of only 10 cm. Significantly, when using the frequencies and resonator capacitances according to the mutual impedance adaption as proposed in this article, the LED TV WPT output power reached peak power at distances varying between 0-60 cm distances.

The efficiency of a multiphase wireless power transfer (WPT) system varies with the size and position of loads. Based on the traditional WPT system, the efficiency improvement of three-phase WPT system under load variation was studied. A three–phase shift control (PSC) strategy is proposed. Mathematical formula of optimal resistance is deduced and the optimal phase shift angles (PSA) for maximum efficiency are presented in the three-phase WPT system. Through the analysis of the electromagnetic model of the system, the optimal phase angle at which the load maintains optimum efficiency at different locations is deriving. A three-phase WPT phase experimental platform based on PSC is built. Verify the validity and correctness of PSC strategy. Simulation and experimental results show that the efficiency of the receiving coil can be increased by 10−15% after the phase is adjusted at different positions. The proposed three-phase phase shift control strategy has a guiding and reference significance for subsequent related research.