SOA pattern effect mitigation by neural network based pre-equalizer for 50G PON.

Coherent reception, along with time- and wavelength-division multiplexing (TWDM), is a promising concept to simultaneously support multiple services in future high-speed point-to-multipoint passive optical networks (PONs). The next-generation PON 2 (NG-PON2) standard describes a TWDM-PON based on IM/DD intensity modulation and direct detection (IM/DD) which employs tunable-lasers and optical filters such as tunable optical filters or cyclic arrayed-waveguide gratings. Here, we investigate what we believe to be a novel coherent TWDM-PON architecture based on a frequency comb source in the optical line terminal (OLT), and thermally-tuned distributed-feedback (DFB) lasers in the optical network units (ONUs). For downstream operation, we broadcast multiple copies of two 25 GBd dual-polarization quadrature phase shift keying (DP-QPSK) signals, resulting in a total PON downstream capacity of 200 Gbit/s. The copies of the downstream signals are spanning ±2 nm (±250 GHz). In the ONUs, we align the wavelengths of the DFB lasers, which act as local oscillators (LOs), to one of the downstream signals by a thermal heater or by changing the direct current. In upstream, the already aligned DFB lasers act as transmit lasers and the frequency comb as LO. We demonstrate TWDM upstream by emulating two ONUs with 25 GBd DP-QPSK, resulting in a total PON upstream capacity of 200 Gbit/s.

An Ethernet passive optical network (EPON) is an optical access network that allows a higher data rate with low power consumption. To improve energy savings for an EPON, the sleep and doze modes for the optical network units (ONUs) play a pivotal role. Many prediction schemes have been proposed to control these modes. To increase the prediction accuracy, this study proposes an energy-efficient approach that uses a support vector regression (SVR) model. A dynamic bandwidth allocation (DBA) scheme called SVR-DBA is designed to allocate bandwidth to ONUs more efficiently and fairly. To determine the effectiveness of the proposed scheme, simulations are performed. The simulation results show that the proposed scheme decreases energy consumption for ONUs by up to 47% and fulfills the quality-of-service (QoS) requirements in terms of delay, jitter, and packet loss.

Energy-efficient passive optical networks (PONs) have gained significant interest since they are estimated to be the largest energy consumers among the wired access networks for the next ten years. In Ethernet PONs (EPONs), the equipment placed at the customer premises, i.e., the optical network units (ONUs), has been shown to be responsible for almost 65% of the total EPON power consumption. Sleep mechanisms, implemented at ONUs’ side, can contribute to the EPONs’ energy-efficiency. However, the tradeoff between energy saving and quality of service (QoS) requirements should be carefully tuned, especially when the downstream transmission is considered, to achieve the desirable results. In this paper, we propose a general framework that exploits formal methods as an approach for EPONs’ energy-efficiency. The idea is to build a holistic model representing both the state machine of the ONU in its details as well as the ONU’s communication with the optical line terminal under EPONs’ specifications. Verification results reveal that, guided by the QoS constraints and considering the transitions’ cost, an “aggressive” policy defining long sleep periods of the 100 ms order can be up to 24.9% beneficial for energy-efficiency compared to a “conservative” policy with sleep periods of the 10 ms order.

Development of modern optical fiber networks puts an increasing demand on the optical hardware. All-optical signal processing components enable the highest switching rates and allow all-optical regeneration of pulse streams without converting the optical signal into electrical current. The subject of our research is self-switching in a Mach-Zehnder interferometer (MZI) and its applications in optical telecommunication networks. In this device, light injected in one of the input ports is unequally distributed over the two interferometer arms. Due to the intensity dependent refractive index in the interferometer arms, there can be a nonlinear phase shift induced between the optical signals of unequal intensities. The two signals therefore interfere destructively or constructively depending on the input power: in this way we obtain nonlinear self-switching. Two mechanisms of nonlinear phase shifting were considered: active, based on semiconductor optical amplifiers (SOAs), and passive, based on quantum dots (QDs). Interferometers of two types were developed: 2-to-2 (two input ports and two output ports) and 2-to-1 (two input ports and one output port). The 2-to-2 SOA-MZIs based on self-switching have been investigated for two applications. One of them is the pattern effect compensator. If SOAs are employed for all-optical signal amplification, e.g. in optical access networks, an unwanted pulse distortion (known also as the pattern effect) takes place, as a result of the SOA gain saturation. Our component allows pattern-free amplification of the optical signals at bitrates up to 20 Gb/s. At 10 Gb/s it shows an extended input power range (up to 7 dB improvement) and comparable gain, which makes it suitable to be used as an optical amplifier. Another application of the 2-to-2 SOA-MZI is a 2R-regenerator. Optical amplifiers used in long distance optical links add noise to the optical signal, causing signal degradation. The signal can be regenerated by passing it through an optical gate with a nonlinear transfer function. The 2-to-2 SOA-MZI has such a nonlinear transfer function. The regeneration capabilities were demonstrated at 2.5 Gb/s by an improvement of the receiver sensitivity of about 2.5 dB. The dynamic characterization of the chips was carried out in a close cooperation with the research group COM at the Technical University of Denmark within the ePIXnet "network of excellence". The 2-to-1 MZI based on self-switching can be used as a low-loss optical combiner. An essential function in optical fiber networks is the combining of optical signals. A serious disadvantage of the conventional type of combiners used in the networks is that they let only half of the power (3 dB) through. In order to compensate for this loss, passive optical combiners are often used in combination with an in-line SOA. The first realization of the low-loss optical combiner uses SOAs as active phase shifters. Such an active low-loss combiner shows an improvement of transmission of over 2 dB compared to a conventional combiner with an in-line SOA. It is therefore expected that the output optical signal-to-noise ratio of the self-switching SOA-MZI is more than 2 dB better than that of a conventional combiner with an in-line SOA. While for the pattern effect compensator and the 2R-regenerator SOAs are used not only for inducing the nonlinear phase shift, but also for sufficient amplification, for the low-loss optical combiner the preferred nonlinear effects should be passive: combination of the signal is a passive function. Therefore, the second realization is based on a novel material, quantum dots. QDs provide improved all-optical nonlinearities resulting in a very small switching energy and large refractive index changes. Such a passive 2-to-1 QD-MZI based on self-switching showed an improvement up to 1.7 dB with respect to a conventional combiner. These improvements have a huge effect on e.g. the power budget in passive optical networks, where a large number of splitting stages are required. The Mach-Zehnder interferometers were realized in the InP/InGaAsP semiconductor material system, which is perfectly suitable for the integration of the photonic integrated circuits for the telecommunication applications. In order to realize both active components (such as e.g. SOAs) and passive components (such as e.g. waveguides, couplers), an active-passive integration technique was applied. This integration was realized in a close cooperation between JDS Uniphase Eindhoven and the COBRA Research Institute. It employs a three-step metal-organic vapor-phase epitaxy regrowth process. The quantum dot material was grown within the COBRA Research Institute. Our MZIs use a ridge waveguide design, for which a reactive ion etching process was developed in the COBRA cleanroom. As a result of photonic integration our integrated Mach-Zehnder interferometers have very small dimensions: less than a square millimeter.

Adopting the pay-as-you-grow approach to upgrade passive optical network (PON) facilities by WDM technology insures the smoothness of the upgrade, and also results in the coexistence of wavelength-fixed/tunable optical network units (ONUs) in WDM/TDM PONs. Dynamic bandwidth allocation (DBA) is the key to support such coexistence of heterogeneous ONUs. Thus, DBA is also the key to support the smooth evolution of PONs. To more fairly coordinate the bandwidth allocation among the coexisting heterogeneous ONUs, a differentiated grant sizing (DGS) scheme is proposed. In DGS, not only the fairness between the wavelength-fixed/tunable ONUs but also the fairness between the lightly/heavily loaded ONUs is taken into account. To further carry out load balancing among wavelengths, a grant scheduling scheme is also proposed to cooperate with the grant sizing scheme. In the grant scheduling scheme, a measure of the ONUs’ flexibility is given, and then the least flexible job first rule (LFJF) is adopted for joint wavelength and time-slot assignment. Finally, to demonstrate the effectiveness of the proposed algorithm, a series of comparative analyses is conducted based on simulation experiments.

In this paper, we propose to use a semiconductor optical amplifier (SOA) in the optical network unit (ONU) to improve the loss budget in time and wavelength division multiplexed-passive optical network (TWDM-PON) systems. The SOA boosts the upstream signal to increase the output power of the electro-absorption modulated laser (EML) and simultaneously pre-amplifies the downstream signal for sensitivity improvement. The penalty caused by cross gain modulation (XGM) effect is negligible due to the low extinction ratio (ER) of upstream signal and the large wavelength difference between upstream and downstream links. In order to achieve a higher output power, the SOA is driven into its saturation region, where the self-phase modulation (SPM) effect converts the intensity into phase information and realizes on-off-keying (OOK) to phase-shifted-keying (PSK) format conversion. In this way, the pattern effect is eliminated, which releases the requirement of gain-clamping on SOA. To further improve the loss budget of upstream link, an Erbium doped fiber amplifier (EDFA) is used in the optical line terminal (OLT) to pre-amplify the received signal. For the downstream direction, directly modulated laser (DML) is used as the laser source. Taking advantage of its carrier-less characteristic, directly modulated signal shows high tolerance to fiber nonlinearity, which could support a downstream launch power as high as + 16 dBm per channel. In addition, the signal is pre-amplified by the SOA in ONU before being detected, so the sensitivity limitation for downstream link is also removed. As a result, a truly passive symmetric 40-Gb/s TWDM-PON was demonstrated, achieving a link loss budget of 51 dB.

The potential for sharing infrastructure costs between a large number of customers and the high data rates allowed by optical fibres make passive optical networks (PONs) an attractive solution to the problem of upgrading current copper-based access networks. Optically-amplified, long reach, time division multiple access (TDMA) PONs or 'SuperPONs' offer the potential to further reduce bandwidth transport costs by enabling the direct connection of access networks and inner core networks, thereby eliminating the costs of the outer core/metro backhaul network. The use of dense wavelength division multiplexing (DWDM) could also allow sharing the same feeder fibre and PON head end equipment between a number of such TDMA SuperPONs, each working at different ITU-grid wavelengths. However, a cost effective access solution should employ a customer optical network unit (ONU), which is independent of the PON wavelength, or colorless, in order to reduce the high inventory and deployment costs of using expensive, wavelength-specified sources at the customer. In this paper we demonstrate for the first time the use of a monolithically-integrated, electroabsorption modulator-semiconductor optical amplifiers (EAM-SOAs) as a colorless ONU in a high performance DWDM SuperPON system. These compact devices offer the potential for low-cost optoelectronic integration with other ONU components together with the ability to modulate at rates up to 10Gbps and beyond. We have used this approach to investigate the feasibility of supporting up to 17 SuperPONs from a single feeder fibre and PON head end, each of 100km-reach accommodating 512 users at 2.5Gb/s or 128 at 10Gb/s.

We propose and experimentally demonstrate three novel schemes for upstream access and local area network emulation among customers in a passive optical network using a single reflective semiconductor optical amplifier (RSOA) placed at the customer premises. The first scheme uses the broadband amplified spontaneous emission spectra of the RSOA for the transport of the local area network traffic among the customers, while the second scheme uses the optical carriers delivered to each optical network unit from the central office for the wavelength seeding of the RSOA to facilitate the transport of the local area network traffic. The third scheme describes the self-seeding process of the RSOA with the use of fiber Bragg gratings placed at the optical network unit to facilitate the upstream access and local area network traffic. These schemes for optical layer local area networking among the customers are experimentally demonstrated with more than 2Gbits/s downstream data, 1Gbit/s upstream access traffic, and 1Gbit/s local area network traffic. Moreover, the results of the experiments of all three schemes are compared further and discussed in terms of bandwidth of the local area network traffic, seeding optical power into the reflective semiconductor optical amplifier, and power budget.

Simultaneous upstream and inter optical network unit communication for long reach PON using single transmitter and self-phase modulation

The evolution of the Ethernet passive optical network (EPON) to the enhanced 10G-EPON standard looks poised to maintain its position as the leading fiber to the home technology worldwide. Fair bandwidth allocation will be a challenge in the near future in plants where 1G and 10G customer premises equipment coexists. In this paper we propose a distributed algorithm, distributed dynamic scheduling for EPON (DDSPON), to dynamically allocate the bandwidth requested by the user equipment with quality of service (QoS) constraints. The proposed algorithm is scalable and simple to re-configure, which facilitates a smoother transition from legacy 1G to 10G networks. By using the DDSPON, enhanced optical network units (ONUs) will take full advantage of the 10 Gb/s rate while legacy 1G ONUs maintain their service level agreement; as a result, the individual performance is maximized for both groups of ONUs. We also present an analytical model to evaluate the algorithm performance in a coexistent 1G/10G network. Finally, we also illustrate the enhancement of the DDSPON to provision the QoS to different services under the DiffServ architecture. Analysis and simulation results validate the effectiveness of the proposed mechanisms.

Detailed numerical investigations are undertaken of wavelength reused bidirectional transmission of adaptively modulated optical OFDM (AMOOFDM) signals over a single SMF in a colorless WDM-PON incorporating a semiconductor optical amplifier (SOA) intensity modulator and a reflective SOA (RSOA) intensity modulator in the optical line termination and optical network unit, respectively. A comprehensive theoretical model describing the performance of such network scenarios is, for the first time, developed, taking into account dynamic optical characteristics of SOA and RSOA intensity modulators as well as the effects of Rayleigh backscattering (RB) and residual downstream signal-induced crosstalk. The developed model is rigorously verified experimentally in RSOA-based real-time end-to-end OOFDM systems at 7.5 Gb/s. It is shown that the RB noise and crosstalk effects are dominant factors limiting the maximum achievable downstream and upstream transmission performance. Under optimum SOA and RSOA operating conditions as well as practical downstream and upstream optical launch powers, 10 Gb/s downstream and 6 Gb/s upstream over 40 km SMF transmissions of conventional double sideband AMOOFDM signals are feasible without utilizing in-line optical amplification and chromatic dispersion compensation. In particular, the aforementioned transmission performance can be improved to 23 Gb/s downstream and 8 Gb/s upstream over 40 km SMFs when single sideband subcarrier modulation is adopted in the downstream systems.

We investigate FTTX (Fiber-to-the Home/Premises/Curb) Passive Optical Networks (PON) for the deployment of broadband access networks such that the opportunities of optical fiber enabled technologies as well as of passive switching equipment can be exploited. We focus on designing the best possible architectures of hybrid FTTX PONs, which embraces both TDM and WDM technology. Advantages of hybrid PONs are twofold: they can (i) offer increased data rate to each user by employing WDM technology, (ii) provide flexible bandwidth utilization by employing TDM technology. We propose a novel network design optimization scheme for greenfield deployment of a set of hybrid PONs. For a given geographical location of an optical line terminal (OLT), a set of optical network units (ONUs) and their corresponding aggregated traffic demand, our proposed optimization scheme determines the design and dimensioning of the most economical set of hybrid PON networks while satisfying unicast/multicast traffic demands and taking into account the signal attenuation constraints. Computational experiments have been conducted on a set of up to 512 ONUs in order to evaluate the performance of the proposed scheme.

We propose and experimentally demonstrate a full-duplex integrated passive optical network (PON) and indoor optical wireless communication (OWC) system. For the PON part, an external cavity laser (ECL) and a directly modulated laser (DML) are used as optical sources for downlink and uplink, respectively. The OWC subsystem utilizes a visible light-emitting diode (LED) for downlink and an infrared LED (IR-LED) for uplink transmission. To enable high spectral efficiency (SE), high-speed transmission, and flexible multiple access with simplified optical network unit (ONU)-side digital signal processing (DSP), multilevel, multiband quadrature amplitude modulation (QAM) and hybrid 128/64/16 Nyquist single-carrier frequency domain equalization (N-SC-FDE) modulation are implemented in this paper. In terms of 62.5 MHz OWC N-SC-FDE signals, the system successfully delivered a further 140 cm indoor distance after transmitting over a span of 25 km standard single mode fiber (SSMF) together with three subbands of 250 MHz PON signals. As a proof of concept, an integrated system of symmetrical full-duplex 5 Gb/s PON and 250 Mb/s OWC at each direction for three wired users and one wireless user is successfully achieved. The measured bit error ratios (BERs) for each user are all smaller than the 7% pre-forward-error-correction (pre-FEC) limit of 3.8 × 10−3, which shows the promising potential and feasibility of this proposal to extend multiple services from metro areas to suburban areas.

We present the use of electronic dispersion pre-compensation at optical line terminals (OLTs) to increase the data rate as well as geographic coverage of passive optical networks (PONs). In time-division multiplexed PONs, the dispersion pre-compensation is made adaptive such that the signal blocks intended for different optical network units (ONUs) are compensated differently, based on the actual dispersions experienced by these signal blocks. We perform numerical simulations to show reach increase in 10-Gb/s PON based on on-off-keying (OOK), as well as data rate increase in 40-Gb/s PON based on high spectral efficiency formats such as pulse-amplitude modulation (PAM) and discrete multi-tone (DMT). All these formats are received by simple direct-detection (DD) receivers, aiming to keep the ONU cost-effective. Furthermore, we propose a novel optical transmitter design based on in-phase/quadrature (IQ) modulation in combination with a continuous wave branch to efficiently generate dispersion pre-compensated optical signals that are suitable for DD receivers.

An FEC scheme combined with weighted scheduling to reduce multicast packet loss in IPTV over PON