Soft-output decision feedback equalisation for orthogonal frequency division multiplexing over doubly selective channels

We generalize the multiuser (CDMA spread spectrum) communication systems to the fading environments. We first extend Verdu's (1986) conventional optimum receiver to Rayleigh-fading environments and then evaluate its performance. Having no knowledge of the received power at the receiving end, we therefore need an estimator to efficiently estimate the received signal strength of each user in fading environments. A linear minimum mean square error (LMMSE) unbiased estimator is proposed to attain this goal. By using the minimum mean square error (MMSE) Bayesian estimation, we further propose the LMMSE bit estimator for efficient demodulation. Its performance is close to the optimum multiuser receiver but with a much simpler polynomial complexity. To further reduce the complexity, we extend the LMMSE estimator to the sequential LMMSE estimator. In sequential estimation, we do not need to implement the matched filter banks and to perform the matrix inversion when estimating. In addition, it converges after approximately 2k iterations, where k is the number of users. With this fast convergence property and the simple structure, the sequential LMMSE estimator provides an attractive alternative to the implementation of a multiuser system.

In this paper we propose a novel turbo equalizer based on the expectation propagation (EP) algorithm. Optimal equalization is computationally unfeasible when high-order modulations and/or large memory channels are used. In these scenarios, low-cost and suboptimal equalizers, such as those based on the linear minimum mean square error (LMMSE), are commonly used. The LMMSE-based equalizer can be efficiently implemented with a Kalman smoother (KS), i.e., a forward and backward Kalman filtering whose predictions are merged in a posterior smoothing step. Recently, it was shown that applying EP at the forward and backward stages of a KS equalizer could significantly improve its performance. In this paper, we investigate applying EP at the smoothing level instead. Also, we propose some further modifications to better exploit the information coming from the channel decoder in turbo equalization schemes. Overall, we remarkably reduce the computational complexity while highly improving the performance in terms of bit error rate.

SummaryThis paper introduces the concept of spatial and media‐based modulated (SMBM) orthogonal frequency division multiplexing (OFDM) as a potential candidate for highly mobile next generation beyond 5G (B5G) wireless communications. The proposed SMBM‐OFDM technique utilizes not only the transmit antenna and channel state indices but also OFDM subcarriers to improve the system performance under high mobility. In addition, this study sheds light on challenging fast time‐varying channel estimation problem of MBM‐based systems by using the linear minimum mean square error (LMMSE) approach due to its optimality to investigate the achievable system performance with the aid of basis expansion modeling. The minimum lower bound on the channel estimation error (Bayesian Cramer–Rao bound) is derived theoretically and shown to be attainable by the considered LMMSE estimator. Moreover, symbol detection performance is provided for different modulation types and higher mobile velocities. Simulation results demonstrate that SMBM‐OFDM system under high mobility is able to provide around 12‐dB performance gains in terms of both channel estimation and symbol detection error compared to conventional spatial modulation (SM)‐OFDM systems without MBM. The presented framework is important due to addressing the high mobility support of SMBM‐OFDM systems for B5G wireless communications in terms of achievable channel estimation and data detection performance.

Channel estimation (CE) is a challenging problem and one of the key technologies in Orthogonal Frequency Division Multiplexing (OFDM) systems. The Linear Minimum Mean Square Error (LMMSE) proposed for OFDM systems has excellent Mean Square Error (MSE) performance. However, the conventional method requires the statistical knowledge of the channel information in advance and the complicated inverse operation of large dimension matrices. In this case, an enhanced fast LMMSE channel estimation using Fast Fourier Transform (FFT) operation and the most significant taps (MST) algorithm for OFDM systems is proposed. This method has the advantage of low computational complexity and no requirement on the detailed channel information. In addition, simulation results demonstrate that the proposed algorithm outperforms other LMMSE methods in terms of bit error rate (BER) without the loss of MSE performance.

Ever since the adoption of the single carrier frequency division multiple access (SC-FDMA) scheme for the uplink in the Long Term Evolution (LTE) standard, there has been much interest in improved receiver algorithms for the same. Successive interference cancelation (SIC) based turbo receivers (Turbo SIC) have been proposed to tackle the multi-stream interference (MSI) for transmission modes such as spatial multiplexing (SM) and multiuser (MU) multiple input multiple output (MIMO). In addition, decision feedback equalizers (DFE) have been discussed as an alternative to the simple linear minimum mean square error (LMMSE) based receivers to suppress intersymbol interference (ISI) caused by the frequency selective multi-path channel. This paper proposes a DFE receiver variant based on parallel interference cancelation (PIC) with maximum likelihood detection (MLD) and ordered SIC (OSIC) principles to suppress ISI and MSI. Simulations show that the proposed receiver performs better than the existing SIC and DFE based receivers and achieves the matched filter bound (MFB) for both coded and uncoded systems.

We derive the Linear Minimum Mean Square Error (LMMSE) receiver for Wyner's model of a linear cellular array. By exploiting the special structure of the channel model, we obtain explicit Mean Square Error (MSE) expressions and information capacity formulae for both finite-sized as well as infinite-sized linear cellular arrays. We show that the performance of an individual user becomes insensitive to the array size for large array sizes and that the proportion of users achieving almost the same performance converges to one, as the array size tends to infinity. The effects of intercell interference and noise on the performance of each user are also investigated.

Pair-wise error probability (PEP) is analyzed in the presence of channel estimation error (CEE) for orthogonal frequency division multiplexing (OFDM) in a quasi-static Rayleigh fading channel. Subcarriers in OFDM are grouped in an equi-spaced manner with the number of subcarriers in a group equal to the number of channel taps. One group is dedicated for training and the rest are for data transmission. A linear minimum mean square error (LMMSE) based channel estimation for coherent detection is considered in this paper. This enables the signal dependent CEE to be uncorrelated to the data. Since ML decoding employed with perfect CSI becomes suboptimal in the presence of CEE, an optimal ML decoding is derived. It is observed from our training-based PEP expression that the CEE does not reduce the diversity order but contributes to a loss of coding gain. Moreover, a code design criterion is established. To reduce the loss of coding gain, an optimal training scheme is developed, based on the PEP expression. Loss of performance due to an imperfect channel estimate is quantified in terms of bounds on bit error probability (BEP) for high SNR. Our analytical findings are corroborated by simulation examples.

In orthogonal frequency division multiplexing (OFDM) systems, the least square (LS) in addition to the technique of linear minimum mean square error (LMMSE) channel estimation are compared using frequency as well as time domain in this paper. A constant LMMSE channel estimation has been proposed in time domain where the channel is not intimated before. It is presented by the Simulation outcomes that the channel estimation execution can be improved by the techniques of time domain but not using the techniques of frequency domain. Additionally, using the technique of LMMSE, higher accuracy is achieved by the proposed method which is presented in the outputs of the simulation.

Photon-counting detectors are greatly improving the resolution and image quality in computed tomography (CT) technology. The drawback is, however, that the reconstruction becomes more challenging. This is because there is a considerable increment of the processing data due to the multiple energy bins and materials in the reconstruction analysis, as well as improved resolution. Yet efficient material decomposition and reconstruction methods tend to generate noisy images that do not completely satisfy the expected image quality. Therefore, there is a need for efficient denoising of the resulting material images. We present a new and fast denoiser that is based on a linear minimum mean square error (LMMSE) estimator. The LMMSE is very fast to compute, but not commonly used for CT image denoising, probably due to its inability to adapt the amount of denoising to different parts of the image and the difficulty to derive accurate statistical properties from the CT data. To overcome these problems we propose a model-based deep learning strategy, that is, a deep neural network that preserves an LMMSE structure (model-based), providing more robustness unseen data, as well as good interpretability to the result. In this way, the solution adapts to the anatomy in every point of the image and noise properties at that particular location. In order to asses the performance of the new method, we compare it to both to a conventional LMMSE estimator and to a “black-box” CNN in a simulation study with anthropomorphic phantoms.

LMMSE and MAP estimators for reduction of multiplicative noise in the nonsubsampled contourlet domain

In this thesis, we cope with the fundamental mathematical and physical problems of the space-time-Doppler UWB system design for fading channels: multi-input multi-output (MIMO) wireless communication with adaptive filtering. The estimation algorithm from equalizer providing an accurate parameters estimate is investigated. UWB radio is a fast emerging technology with uniquely attractively features inviting major advances in wireless communications, networking, radar, imaging, and positioning systems. By its rule-making proposal in 2002, the Federal Communications Commission (FCC) in the United States essentially unleashed huge new bandwidth (3.6-10.6 GHz) at the noise floor, where UWB radios overlaying coexistence RF systems cerate using low-power ultra-short information bearing pulses. Right now, there are three basic types of UWB: multiband OFDM UWB (MB-OFDM UWB), impulse-UWB (I-UWB), and direct sequence UWB (DS-UWB). We focus on I-UWB and MB-OFDM-UWB, and compare their performance. A simple means for spreading the spectrum of low duty cycle pulse trains is time hopping (TH), with pulse position modulation (PPM) for data modulation at the rate of many pulses per data bit. The main contribution of this thesis for I-UWB is the design of leading edge detectors, coherent correlation detector (CCD), and pilot performance enhancement compared with different Rayleigh and Ricean fading conditions. For MB-OFDM UWB, we have considered the performance analysis and design criteria of MIMO OFDM UWB systems for high data-rate wireless transmission. The signal processing of frame detection, time synchronization, frequency synchronization, channel estimation, synchronization tracking using pilot subcarriers and 2-D MIMO detection algorithms is discussed. The main contributions of this thesis are 1) Compared with receiver employing the Maximum Likelihood (ML) detector, the receiver employing a low-complexity linear Minimum Mean Square Error (MMSE) demodulator can perform a limited performance loss in spatially uncorrelated channels. 2) Due to the operations of spreading and dispreading combined with MMSE-based frequency domain equalization, the adverse effects of the low-SNR subcarriers on the average BER performance are potentially improved. This is a direct consequence of spreading, because even if the signal corresponding to a specific chip is obliterated by a deep frequency domain channel fade, after dispreading these effects are spread over the Walsh-Hadamard Transform (WHT) length. Hence there is a high chance of still recovering all the partially affected subcarrier symbols without errors. 3) As a test case, the OFDM-based 200 Mb/s MB-UWB network (IEEE 802.15.3a) are considered, but the simulation results are shown above section. 4) The simulation channel can be easily applied to NOS and NLOS situation with WHT transformation from Simulink model. The fading channels of UWB with low/high signal to noise ratio (SNR), multipath effects, and multiuser interference may introduce large errors in location. The location engine performs the following tasks: █ Data fusion techniques: Different data fusion techniques are implemented using Time Of Arrival (TOA), Angle Of Arrival (AOA), or a combination of both. █ Channel modeling: A multipath, multiuser channel environment is created that models path loss, shadowing, Rayleigh fading, and Doppler frequency effects. █ Parameter estimation: TOA and AOA estimation algorithms are implemented as part of the location finding engine. Different variations of algorithms are implemented for performance and comparison purposes. █ Configuring the physical layer for different wireless networks. Among the programmable parameters are spreading factor, packet size, training length, constellation type, modulation technique, carrier frequency, level of transmitted signal power, and the number of antennas at the transmitter for both sides. █ Configuring the mobile user conditions. The wireless channel models depend on the Doppler frequencies present in the environment. The Doppler frequency depends on the mobile speed and carrier frequencies as input and generates a Rayleigh fading channel with the U-shape Doppler spectrum. █ Configuring the environmental parameters and network geographical structure. One of the factors affecting the performance of the wireless location system is the environment type (e.g., bad urban, urban, suburban, or rural area). For example, in a bad urban area with many blocking objects and buildings, non-line of sight (NLOS) effects plays an important role in the estimation accuracy.

Channel estimation is a critical component in orthogonal frequency division multiplexing (OFDM) systems for ensuring reliable wireless communication. In this study, we propose a fast super-resolution convolutional neural network (FSRCNN) model for channel estimation, designed to reduce computational complexity while maintaining high estimation accuracy. The proposed FSRCNN model incorporates modifications such as replacing linear interpolation with zero padding and leveraging a new fast CNN architecture to estimate channel coefficients. Our numerical experiments and simulations demonstrate that the FSRCNN model significantly outperforms traditional methods, such as least square (LS) and linear minimum mean square error (LMMSE), in terms of mean square error (MSE) across various signal-to-noise ratios (SNRs). Specifically, the FSRCNN model achieves MSE values comparable to MMSE estimation, particularly at higher SNRs, while maintaining lower computational complexity. At an SNR of 20 dB, the FSRCNN model shows a notable improvement in MSE performance compared to the ChannelNet and LS methods. The proposed model also demonstrates robust performance across different SNR levels, with optimal results observed when the training SNR is close to the operating SNR. These findings validate the effectiveness of the FSRCNN model in providing a low-complexity, high-accuracy alternative for channel estimation, making it suitable for real-time applications and devices with limited computational resources. This advancement holds significant promise for enhancing the reliability and efficiency of current and future wireless communication networks.

In recent years, there has been an increased need for digital wireless applications to use high rate data transmission. OFDM (Orthogonal Frequency Division Multiplexing) offers an interesting solution that allows for the exploitation of the 60 GHz band with optimal spectral efficiency, a robustness to frequency selective fading, and a resistance to inter-symbol interference (ISI) that is a major problem in high speed data communications. Transmitted data in an OFDM system is divided on different subcarriers, after applying PSK (phase shift keying) or QAM (Quadrature Amplitude Modulation) modulation. The bandwidth of the obtained signal is converted to the time domain by using an IFFT (Inverse Fast Fourier Transform) in order to transmit it through a wireless channel. To recover the distorted data at the receiver, the effects of the channel must be estimated and compensated by the receiving system [1, 2]. In this paper, the 60 GHz channel estimation methods for OFDM systems based on comb-type pilot arrangement are investigated, as the algorithm of channel estimation based on comb-type is divided into pilot signal estimation and channel interpolation. The pilot signal estimation based on LS (Least Squares) or LMMSE (Linear Minimum Mean Square Error) criteria is studied along with the channel interpolation based on LI (linear interpolation). The performances of various estimation algorithms are evaluated and compared by measuring the Bit Error rate (BER) and Mean Square Error (MSE) where 16-QAM modulation scheme is applied.

Orthogonal frequency division multiplexing (OFDM) is multi carrier modulation scheme. The channel estimation is a process of characterizing the effect of the transmission channel on the input signal. In this paper we compare the performance of Least Square (LS) and Linear Minimum Mean Square Error (LMMSE) channel estimation technique for Wavelet based OFDM system. The channel estimation based on block type pilot arrangement is performed by sending pilots at every sub-channel and using this estimation for a specific number of following symbols. In this paper we used wavelet transform instead of fast Fourier transform (FFT), which have more bandwidth efficiency, less prone to Doppler shift and also complexity of order O(N) as opposed to the FFTs O(N log <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sub> N).

The basic idea of this letter is concerned with the large Peak-to-Average Power Ratio (PAPR) problem in multi-carrier Under-Water Acoustic (UWA) communication systems that implement Orthogonal Frequency Division Multiplexing (OFDM). A Tangent Rooting (TanhR) companding technique is presented in this paper to reduce the PAPR in UWA communication systems. This technique achieves a noticeable reduction of the PAPR in UWA systems, while maintaining a good Bit Error Rate (BER) performance . Channel equalisation with Linear Minimum Mean Square Error (LMMSE) and Zero-Forcing (ZF) equalisers is considered in this paper. Simulation results ensure superiority of the proposed technique compared to the Selected Mapping (SLM) and the Partial Transmit Sequence (PTS) techniques from both the PAPR and BER perspectives.