- Research Article
33
- 10.1016/0003-4916(65)90260-5
Experiments on the stability of two types of spiral flow
- Feb 01, 1965
- Annals of Physics
- H.A Snyder
Experiments on the stability of two types of spiral flow
A thermal gradients’ field was studied for an as cast massive roll. Three ranges within the thermal gradients field were differentiated. The thermal gradient is constant along with the second range of thermal gradients’ field. Thus, columnar into equiaxed structure transition (CET) is to be expected within the second range. This statement is in good qualitative agreement with a similar observation given by Hunt’s theory. The columnar structure formation was significantly slowed down within the second range of thermal gradients field. At beginning of the second range the liquidus isotherm tears away from columnar structure / liquid interface. The columnar structure is still formed within the time adequate to the second range of thermal gradients but its growth vanishes due to lost competition, and at the end of the second range the equiaxed structure growth dominates, exclusively. In fact, the extrapolation of the velocity of the columnar structure / liquid interface to its value equal with zero confirms the appropriate location of the end of the second range within which the CET is observed. The detailed analysis of the solidus isotherm / liquidus isotherm movements allows a development of the Space-Time-Structure Map for a solidifying massive roll. The Map shows the location of the CET in time (solidification time) and in space (along the roll radius). Moreover a proper locations of structural zones are drawn in the Map. The simulation of the thermal gradients’ field is a very useful tool in the industrial practice. The results of simulation can be used to predict the Space-Time-Structure Map (STSM) for a given massive roll or a massive ingot. Additionally, the equation for solute redistribution after back-diffusion was formulated on the basis of the new theory for microsegregation. It allows formulating the so-called macrosegregation index dealing with the whole ingot/roll volume.
Experiments on the stability of two types of spiral flow
Experiments on the stability of two types of spiral flow
Effects of Thermal Gradient and Solidification Time on Porosity Content of A201 Aluminum Alloy Castings
The purpose of the present study was to discuss the effects of local solidification time and thermal gradient on porosity content in long solidification range A201 aluminum alloy plate castings. With systematic change in the riser size, together with variation of thickness and length, were cast in different kinds of molds. The sand molds with end chill for the plate castings were made of 100% silica sand. The porosity content of A201 aluminum alloy was affected by the local solidification time and thermal gradient at same time in this study. The correlation between porosity content and any individual thermal parameter is found to be split into 2 bands, each being associated with one of the two thicknesses of plate castings. The higher the thermal gradient, the lower the porosity content was measured in the A201 aluminum alloy plate casting. And high thermal gradient with short solidification time will get lower porosity content in aluminum alloy castings
Read moreSuppression of columnar-structure formation in Mo-Si layered synthetic microstructures
We have previously reported that columnar-structures were formed in electron beam (EB) deposited and DCmagnetron sputtered Mo-Si layered synthetic microstructures (LSMs). The columnar structures reduced x-ray reflectivity by roughing layer interfaces of the LSMs. We here investigated the conditions to suppress columnar structure formation, by varying the substrate temperature (T9) in EB deposition and the argon pressure (PAT ) in D C- and RF-sputtering. In the EB deposited LSMs, the columnar structure disappeared and almost uniform LSMs were obtamed both at Ts 400°C and T9< -155°C. In the DC- and RF-sputtered LSMs, the columnar structure formation was suppressed by lowering PAr. The measured x-ray reflectivity of the LSMs increased according to the suppression of the columnar structure formation.
Read moreThe effect of hot zone velocity and temperature gradient on the directional recrystallization of polycrystalline nickel
The effect of hot zone velocity and temperature gradient on the directional recrystallization of polycrystalline nickel
Phase Field Simulations of Microstructure Evolution in IN718 Using a Surrogate Ni–Fe–Nb Alloy during Laser Powder Bed Fusion
The solidification microstructure in IN718 during additive manufacturing was modeled using phase field simulations. The novelty of the research includes the use of a surrogate Ni–Fe–Nb alloy that has the same equilibrium solidification range as IN718 as the model system for phase field simulations, the integration of the model alloy thermodynamics with the phase field simulations, and the use of high-performance computing tools to perform the simulations with a high enough spatial resolution for realistically capturing the dendrite morphology and the level of microsegregation seen under additive manufacturing conditions. Heat transfer and fluid flow models were used to compute the steady state temperature gradient and an average value of the solid-liquid (s-l) interface velocity that were used as input for the phase field simulations. The simulations show that the solidification morphology is sensitive to the spacing between the columnar structures. Spacing narrower than a critical value results in continued growth of a columnar microstructure, while above a critical value the columnar structure evolves into a columnar dendritic structure through the formation of secondary arms. These results are discussed in terms of the existing columnar to dendritic transition (CDT) theories. The measured interdendritic Nb concentration, the primary and secondary arm spacing is in reasonable agreement with experimental measurements performed on the nickel-base superalloy IN718.
Read moreThe Sensitivity of Investment Casting Simulations to the Accuracy of Thermophysical Property Values
In this study, the importance of the accuracy of the thermophysical property to a simulation of an investment cast directionally solidified nickel-based superalloy turbine blade was investigated. CMSX-4 was chosen as the base alloy. The effect of the thermophysical properties on the thermal field and solidification microstructure was studied using a coupled macromesoscale model. Relevant thermophysical properties examined include density, specific heat (enthalpy) and thermal conductivity in both the liquid and the solid phases. Commercial finite-element analysis software, ProCAST, was used as the macroscale model to solve the heat and mass transportation equations. An in-house mesoscale code was used to simulate the dendritic solidification structure including microsegregation. During the macroscale analysis, the simulation results were compared to an idealized turbine blade previously cast under industrial conditions. In the mesoscale simulation, the response of primary arm spacing and segregation range was examined. The temperature prediction and the thermal gradient in the liquid show the greatest sensitivity to density and solid state thermal conductivity. Primary arm spacing is most sensitive to density and specific heat. Segregation range shows greatest sensitivity to density and thermal diffusivity in the solid.
Read moreInvestigation on morphology evolution of secondary branch during peritectic solidification in a temperature gradient through morphology characteristic: Experimental measurement and prediction
Investigation on morphology evolution of secondary branch during peritectic solidification in a temperature gradient through morphology characteristic: Experimental measurement and prediction
Read moreThe influence of internal chills on the structure and properties of aluminium alloy castings
Many of the drawbacks associated with the production of conventionally cast ingots and castings, such as the presence of pipes, centre-line segregation and columnar grains, can be attributed to the manner and extent of cooling inside the mould cavity and the problems of heat transfer from the centre to the outside of the casting. These result in lowering of the average mechanical properties and the yield of the casting. In the past, the use of external chills to reduce the above defects has had limited effects. This is because the influence of external chills becomes marginal beyond a certain distance. One of the potential methods of overcoming such problems is to employ heat sinks in the form of internal chills. Despite reported work by Russian and Japanese investigators on the use of internal chills, in the form of powder or strip, in iron and steel castings, no detailed information on the use of such chills in aluminium or other non-ferrous alloys is available in the literature.This paper presents details and findings of an investigation carried out with Al-4.5% Cu (LM11) alloy using chills of cylindrical form of the same composition. The influence of such internal chills, placed centrally and non-centrally was assessed in terms of changes in solidification time, temperature gradient, percentage melting, microstructure, density, and the ultimate tensile strength of the castings.The investigation has shown that solidification time decreases linearly with the percentage volume of the chills. Progressive structural refinement, corresponding to this reduction in solidification time, has also been observed. Distribution of the chills is seen to play an important role. One centrally-placed chill is essential in the refinement of the structure of the central region of an ingot, as well as to reduce the size of the central open pipe. The use of microchills in the form of turnings and powder has also been found to refine the structure considerably. The density and ultimate tensile strength of castings has been found to increase up to the optimum volume of chill, i.e. 2.5% at 75–115 K and 0.63% at 35 K superheat, and then decrease.
Read moreThe Control of Solidification of Ni‐Based Superalloy Single‐Crystal Blade by Mold Design Modification using Inner Radiation Baffle
This work is focused on an investigation of the directional solidification process of CMSX‐4 single‐crystal blades in the mold modified by application of inner radiation baffle (IRB). Micro‐ and macrostructure examination is carried out along the height of single‐crystal blades which are manufactured using standard and modified mold, at the withdrawal rates of 3 and 5 mm min−1. It is established that application of modified mold allows better control over liquidus isotherm and leads to increase in temperature gradient, as compared to the manufacturing of blades using standard mold. The average value of temperature gradient in airfoil increases from 14 up to approx. 30 K cm−1 and from 16 up to approx. 40 K cm−1, for withdrawal rate of 5 and 3 mm min−1, respectively. The curvature of liquidus isotherm diminishes and attains near‐flat profile along the airfoil for both values of withdrawal rate. The application of proposed technique results in reduction of primary dendrites arm spacing (PDAS) particularly in the inner and middle part of the blade. PDAS reaches average value of approx. 360 μm for withdrawal rate of 5 mm min−1 and is lower as compared to the standard mold casting withdrawn at the rate of 3 (433 μm) and 5 mm min−1 (468 μm).
Read moreCombined Kelvin–Helmholtz and Marangoni instability and its role in formation of nanostructures under electron-beam irradiation
This paper examines the development of nanostructural layers in silumin alloyed in electrical explosion of yttrium and processed with low-energy high-current electron beams. The study has established the electron-beam processing results in columnar structures (200 nm to 1 µm) with silicon and yttrium atoms at their boundaries. A mechanism responsible for the formation of these structures is associated with a combination of Marangoni and Kelvin–Helmholtz instabilities caused by a temperature gradient and a transverse velocity of the melt. The reported research investigates a flow of a viscous double-layered incompressible heat-conducting fluid. A first stable layer is silumin, and the other one (yttrium) moves at a velocity parallel to a base plane. Navier–Stokes and heat conductivity equations, as well as boundary conditions are given for each layer. A solution to equations has been found using the method of finite elements. The results of the study indicate the ever increasing disturbance of the interface irrespectively to a velocity. Disturbances of the interface are shown to turn into “drops” penetrating as deep as 20–60 µm at a transverse velocity of 0 m/s in a time frame from 80 to 150 µs. It is much deeper than a penetration depth of yttrium due to the diffusion mechanism. An increase of a velocity up to 4 m/s transforms a melt flow. A transformation of disturbances into drops is recorded at t>800 µs, so a stabilizing effect of Kelvin–Helmholtz instability is highlighted.
Read moreEffects of Gravitational orientation on the microstructural evolution of gas tungsten arc welds in an Al-4 wt% Cu alloy
Gas tungsten arc (GTA) welds on Al-4 wt% Cu alloys were investigated to determine effects of gravitational orientation on the weld solidification behavior. A bead-on-plate welding was performed by varying the relation between the arc translation direction and gravity vector, e.g., parallel-up, parallel-down, and perpendicular orientations. A solidification rate (VS) was calculated from the measured grain orientation, and a thermal gradient (GL) was estimated from the observed weld pool shape following a linear relation. A primary dendrite spacing (λ1) decreased continuously from the s-l boundary to the weld pool surface regardless of the gravitational orientations. Larger λ1 for the parallel-up weld was observed near the boundary and surface than that of the perpendicular and parallel-down welds, which is believed to be associated with a smaller GL due to larger weld pool dimension and with different solidification morphology. A solidification morphology and orientation in the perpendicular and parallel-up welds was comparable with a loss of columnar directionality near the weld surface and a continuous grain orientation. However, the parallel-down weld exhibited more columnar structure near the surface, which might be associated with the larger GL and relatively mild convection flows. Outward convection flows in the parallel-down weld might be inhibited because of its reverse direction with respect to the gravity vector. This resulted in abnormal ‘S’ shape of the trailing s-l interface and the VS, which was receded toward the weld pool center. Based on these findings, significant influence of gravitational orientation resulted in the variation on the weld pool shape associated with convection flows, which in turn affected solidification orientation/morphology and the primary dendrite spacing.
Read moreEffect of boundary heat flux on columnar formation in binary alloys: A phase-field study
A non-isothermal phase-field model was employed to simulate the columnar formation during rapid solidification in binary Ni–Cu alloy. Heat flux at different boundaries was applied to investigate the temperature gradient effect on the morphology, concentration and temperature distributions during directional solidifications. With the heat flux input/extraction from boundaries, coupling with latent heat release and initial temperature gradient, temperature distributions are significantly changed, leading to solute diffusion changes during the phase-transition. Thus, irregular columnar structures are formed during the directional solidification, and the concentration distribution in solid columnar arms could also be changed due to the different growing speeds and temperature distributions at the solid–liquid interfaces. Therefore, applying specific heat conditions at the solidifying boundaries could be an efficient way to control the microstructure during solidifications.
Read moreEffect of temperature gradient on liquid-liquid phase separation in a polyolefin blend
We have investigated experimentally the structure formation processes during phase separation via spinodal decomposition above and below the spinodal line in a binary polymer blend system exposed to in-plane stationary thermal gradients using phase contrast optical microscopy and temperature gradient hot stage. Below the spinodal line there is a coupling of concentration fluctuations and thermal gradient imposed by the temperature gradient hot stage. Also under the thermal gradient annealing phase-separated domains grow faster compared with the system under homogeneous temperature annealing on a zero-gradient or a conventional hot stage. We suggest that the in-plane thermal gradient accelerates phase separation through the enhancement in concentration fluctuations in the early and intermediate stages of spinodal decomposition. In a thermal gradient field, the strength of concentration fluctuation close to the critical point (above the spinodal line) is strong enough to induce phase separation even in one-phase regime of the phase diagram. In the presence of a temperature gradient the equilibrium phase diagrams are no longer valid, and the systems with an upper critical solution temperature can be quenched into phase separation by applying the stationary temperature gradient. The in-plane temperature gradient drives enhanced concentration fluctuations in a binary polymer blend system above and below the spinodal line.
Read moreThe migration of liquid droplets in solids
The migration of liquid droplets in solids
Pressure-Driven Nitrogen Flow in Divergent Microchannels with Isothermal Walls
Gas flow and heat transfer in confined geometries at micro-and nanoscales differ considerably from those at macro-scales, mainly due to nonequilibrium effects such as velocity slip and temperature jump. Nonequilibrium effects increase with a decrease in the characteristic length-scale of the fluid flow or the gas density, leading to the failure of the standard Navier–Stokes–Fourier (NSF) equations in predicting thermal and fluid flow fields. The direct simulation Monte Carlo (DSMC) method is employed in the present work to investigate pressure-driven nitrogen flow in divergent microchannels with various divergence angles and isothermal walls. The thermal fields obtained from numerical simulations are analysed for different inlet-to-outlet pressure ratios (1.5≤Π≤2.5), tangential momentum accommodation coefficients, and Knudsen numbers (0.05≤Kn≤12.5), covering slip to free-molecular rarefaction regimes. The thermal field in the microchannel is predicted, heat-lines are visualised, and the physics of heat transfer in the microchannel is discussed. Due to the rarefaction effects, the direction of heat flow is largely opposite to that of the mass flow. However, the interplay between thermal and pressure gradients, which are affected by geometrical configurations of the microchannel and the applied boundary conditions, determines the net heat flow direction. Additionally, the occurrence of thermal separation and cold-to-hot heat transfer (also known as anti-Fourier heat transfer) in divergent microchannels is explained.
Read more