• Home
  • Search
  • SPECIFICATION FOR TESTING GAS DISCHARGE LIGHT SOURCE SUBSYSTEM
  • https://doi.org/10.4271/uscar27Copy DOI Icon

SPECIFICATION FOR TESTING GAS DISCHARGE LIGHT SOURCE SUBSYSTEM

  • Feb 23, 2017
  • Uscar
Show More
  • Abstract
  • Literature Map
  • Similar Papers
Abstract

<div class="section abstract"> <div class="htmlview paragraph">This specification is a general level subsystem light source specification that establishes test requirements of a Gas Discharge Light Source (GDLS) subsystem for use on passenger vehicles.</div> <div class="htmlview paragraph">The completed test data to this test specification is intended to be provided to the OEM by the Tier one lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved GDLS experiences a design, manufacturing or component change.</div> <div class="htmlview paragraph">This document shall be applied to systems that meet the requirements for design, performance and validation established by government standards.</div> <div class="htmlview paragraph">The subsystem is defined as the ballast, igniter and light source and shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the test sample shall constitute a failure of the entire sample. Substitution or replacement of only the light source shall be allowed during testing. Failure of the light source more than once in a tested system shall constitute a failure of the GDLS. <i>If other manufacture’s components are intended to be approved for use in the GDLS, then those possible combinations of components shall be considered a new GDLS and shall also be tested</i>.</div> <div class="htmlview paragraph">Additional testing may be required by individual OEM’s to meet specific EMC, quality, reliability and durability objectives.</div> <div class="htmlview paragraph">The following tests are to be performed under the following conditions:</div> <ul class="list disc"> <li class="list-item"> <div class="htmlview paragraph">New light source (capsule) or ballast design</div></li> <li class="list-item"> <div class="htmlview paragraph">Design or process change made to an existing capsule or ballast, which could affect the outcome of the test</div></li> <li class="list-item"> <div class="htmlview paragraph">Completion of one calendar year as noted in the “ANNUAL TESTS” Table shown in the Appendix. <i>(Note: Production process control data, collected at a shorter interval per an approved control plan, may be substituted if approved by customer’s responsible engineer and purchasing representative.)</i></div></li></ul></div>

Similar Papers
  • Conference Article
  • Citations13

Improved Projector Headlamps Using HID (Litronic) and Incandescent Bulbs

  • Mar 01, 1994
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Rainer Neumann
  • Conference Article
  • Citations3

Signal Image Enhancement of Projection Type Headlamps by Additional Optics

  • Mar 05, 2001
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Henning Weinhold +2
  • Standard
  • Citations2

PERFORMANCE SPECIFICATION FOR ULTRASONICALLY WELDED WIRE TERMINATIONS

  • Feb 13, 2017
  • Uscar
  • Conference Article
  • Citations8

Combustion Behavior Analysis in a Transparent Research Engine Equipped with a Common Rail Diesel Injection System

  • Jun 19, 2000
  • SAE technical papers on CD-ROM/SAE technical paper series
  • C Beatrice +4
  • Conference Article
  • Citations5

The Effect of Reachability on Global Comfort Perception: The Case of Front-seat Car Passengers

  • Apr 03, 2018
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Alessandro Naddeo +5
  • Conference Article

High Efficiency Light Source for Distributive Lighting Systems (DLS)

  • Mar 05, 2001
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Thomas Luce +2
  • Conference Article
  • Citations11

Ultrasonic Sensor Modeling for Automatic Parallel Parking Systems in Passenger Cars

  • Apr 16, 2007
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Pär Degerman +2
  • Conference Article

Experimental Test Bench Showcasing an X in the Loop Strategy for Fuel Cell Testing

  • Nov 05, 2024
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Tancrède Oswald +2
  • Conference Article
  • Citations1

Investigation for Observing Presence and Distribution of Phenolic Resin in Friction Materials

  • Oct 10, 2004
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Shinichi Ozeki
  • Standard
  • Citations1

Measurement of Aerodynamic Performance for Mass-Produced Cars and Light-Duty Trucks

  • Oct 10, 2019
  • Road Vehicle Aerodynamics Forum Committee
  • Standard
  • Citations1

LABORATORY MEASUREMENT OF THE COMPOSITE VIBRATION DAMPING PROPERTIES OF MATERIALS ON A SUPPORTING STEEL BAR

  • Mar 07, 2017
  • Acoustical Materials Committee
  • Standard
  • Citations1

Laboratory Measurement of the Composite Vibration Damping Properties of Materials on a Supporting Steel Bar

  • Feb 18, 2022
  • Acoustical Materials Committee
  • Conference Article
  • Citations35

Emissions from Current Diesel Vehicles

  • Oct 01, 1994
  • SAE technical papers on CD-ROM/SAE technical paper series
  • R H Hammerle +5
  • Conference Article
  • Citations4

Design Optimization of Engine Mount De-Coupler for Cabin Noise Refinement in Passenger Vehicle

  • Jan 09, 2019
  • SAE technical papers on CD-ROM/SAE technical paper series
  • Pallavi Verma +3
  • Standard

Measurement of Passenger Compartment Refrigerant Concentrations Under System Refrigerant Leakage Conditions

  • Feb 20, 2017
  • Interior Climate Control Vehicle Oem Committee
Cactus Communications logo

Copyright 2026 Cactus Communications. All rights reserved.