Study of MSI300 Propeller Characteristics Using Computational Fluid Dynamics Analysis

Autonomous underwater vehicles (AUVs) have become main tools for underwater survey in scientific, military, and commercial applications. A significant amount of onboard power is needed to execute long-range missions; however, energy storage is limited in AUV. This paper presents a novel landing AUV that can land on the sea floor to perform long-term monitoring and measuring tasks and save onboard electric energy. The AUV has following characteristics. Firstly, a triangular structure of the AUV which is composed of three cabins is used to achieve stable bottom sitting. Secondly, the releasing mechanism is designed to eject and recover the AUV. Bottom sitting and recovering is verified by ocean trials. This paper provides guidance for design of similar AUVs.

Autonomous underwater vehicles (AUVs) have many, scientific, military, and commercial applications because of their potential capabilities and significant cost-performance improvements. Typical AUV development requires critical system design and many costly at-sea trials during which systems specifications can be validated. Modeling and simulation provides a cost-effective method for carrying out preliminary component or system (hardware and software) testing and verification. Due to the complexity of most AUV development and their tight schedules, the simulated systems often differ considerably from the actual embedded architecture, thereby reducing the fidelity of the entire simulation. We adopted a hardware-in-the-loop (HIL) simulation approach that includes some level of the system's hardware and software. As expected, an HIL simulation requires all components be run under hard real-time constraint. The paper presents our implementation and considerations on HIL simulation for single and multiple vehicles. A brief mention of sensor and environment modeling is also provided.

While designing the power requirements of a ship, the most important factor to be considered is the ship resistance, or the sea drag forces acting on the ship. It is important to have an estimate of the ship resistance while designing the propulsion system since the power required to overcome the sea drag forces contribute to ‘losses’ in the propulsion system. There are three main methods to calculate ship resistance: Statistical methods like the Holtrop-Mennen (HM) method, numerical analysis or CFD (Computational Fluid Dynamics) simulations, and model testing, i.e. scaled model tests in towing tanks. At the start of the design stage, when only basic ship parameters are available, only statistical models like the HM method can be used. Numerical analysis/ CFD simulations and model tests can be performed only when the complete 3D design of the ship is completed. The present paper aims at predicting the calm water ship resistance using CFD simulations, using the Flow-3D software package. A case study of a roll-on/roll-off passenger (RoPax) ferry was investigated. Ship resistance was calculated at various ship speeds. Since the mesh affects the results in any CFD simulation, multiple meshes were used to check the mesh sensitivity. The results from the simulations were compared with the estimate from the HM method. The results from simulations agreed well with the HM method for low ship speeds. The difference in the results was considerably high compared to the HM method for higher ship speeds. The capability of Flow-3D to perform ship resistance analysis was demonstrated.

Bench test and computational fluid dynamics (CFD ) simulation of the air pump loss on the 380 hydraulic retarder are completed in this paper . It turns out that the CFD simulation has nice reliability from the contrast of the air pump loss between the test and the simulation . And on this foundation , CFD simulation of two kinds of retarders with different turbulent structures is done . The contrast of the results of the simulation give the effects of different turbulent structures on cutting down the are pump loss .

Optimization methods have been widely applied to the aerodynamic design of gas turbine blades. While applying optimization to high-fidelity computational fluid dynamics (CFD) simulations has proven capable of improving engineering design performance, a challenge has been overcoming the prolonged run-time due to the computationally expensive CFD runs. Reduced-order models and, more recently, machine learning methods have been increasingly used in gas turbine studies to predict performance metrics and operational characteristics, model turbulence, and optimize designs. The application of machine learning methods allows for utilizing existing knowledge and datasets from different sources, such as previous experiments, CFD, low-fidelity simulations, 1D or system-level studies. The present study investigates inserting a machine learning model that utilizes such data into a high-fidelity CFD driven optimization process, and hence effectively reduces the number of required evaluations of the CFD model. Artificial Neural Network (ANN) models were trained on data from over three thousand two-dimensional (2D) CFD analyses of turbine blade cross-sections. The trained ANN models were then used as surrogates in a nested optimization process alongside a full three-dimensional Navier–Stokes CFD simulation. The much lower evaluation cost of the ANN model allows for tens of thousands of design evaluations to guide the search of the best blade profiles to be used in the more expensive, high-fidelity CFD runs, improving the progress of the optimization while reducing the required computation time. It is estimated that the current workflow achieves a five-fold reduction in computational time in comparison to an optimization process that is based on three-dimensional (3D) CFD simulations alone. The methodology is demonstrated on the NASA/General Electric Energy Efficient Engine (E3) high pressure turbine blade and found Pareto front designs with improved blade efficiency and power over the baseline. Quantitative analysis of the optimization data reveals that some design parameters in the present study are more influential than others, such as the lean angle and tip scaling factor. Examining the optimized designs also provides insight into the physics, showing that the optimized designs have a lower amount of pressure drop near the trailing edge, but have an earlier onset of pressure drop on the suction side surface when compared to the baseline design, contributing to the observed improvements in efficiency and power.

A normally-open thermally-actuated microvalve was designed (using microfabrication/soft-lithography techniques involving 3D Printed molds), assembled and tested. The motivation of the research work is to develop an array of microvalves for precise delivery of water to individual plants in a field (with the goal of developing smart irrigation systems for high value cash-crops in the agricultural sector). It is currently impossible to control application of irrigation-water at the level of a single plant. If such a capability were practically available on farms, the result would be a step change in precision agriculture, such that the output of every plant in a farm field could be optimized (i.e., food-water-energy nexus in sustainability applications). The aim of this study is to develop and test a microfluidic system (consisting of a microvalve array) that could be controlled, capillary by capillary, to deliver the needed amount of water to individual plants in a large field. Two types of test fluids were leveraged for thermo-hydraulic actuation of the microvalves developed in this study: (a) Design-I: using air, and (b) Design-II: using Phase Change Material (PCM). The PCM used in this study is PureTemp29. The proposed approach enabled a simple and cheap design for microvalves that can be manufactured easily and are robust to weather conditions (e.g., when exposed to the elements in orchards and open fields). Other advantages include: safe and reliable operation; low power consumption; can tolerate anomalous pressure loads/fluctuations; simple actuation; affords easy control schemes; is amenable for remote control; provides long-term reliability (life-cycle duration estimated to be 3∼5 years); can be mass produced and is low maintenance (possibly requiring no maintenance over the life time of operation). The microvalve consists of two layers: a flow layer and a control layer. The control layer is heated from below and contains a microfluidic chamber with a flexible polymeric thin-membrane (200 microns in thickness) on top. The device is microfabricated from Poly-Di-Methyl-Siloxane (PDMS) using soft lithography techniques (using a 3D Printed mold). The control chamber contains either air (thermo-pneumatic actuation) or PCM (thermo-hydraulic actuation involving repeated melting/freezing of PCM). The flow layer contains the flow channel (inlet and outlet ports, horizontal section and valve seat). The experimental results from testing the efficacy of the two types of micro-valves show a 60% reduction (for thermo-pneumatic actuation using air) and 40% reduction (for thermo-hydraulic actuation using PCM) in water flow rates for similar actuation conditions (i.e., heater temperature values). PCM design is expected to consume less power (lower OPEX) for long-term actuation but may have slower actuation speed and have higher manufacturing costs (CAPEX). Air actuation design is expected to consume more power (higher OPEX) for longer-term operation but may have faster actuation speeds and lower manufacturing costs (CAPEX). Computational Fluid Dynamics (CFD) simulations were performed to investigate the effect of flowing water (in the microfluidic channel) on the average absolute pressure and temperature of air in the actuation chamber. The CFD simulations were performed using a commercial tool (Ansys™ 2019R1®). The results from the CFD simulations are presented in this study.

Today, many wells in heterogeneous carbonate reservoirs throughout the Middle East and Caspian Sea area are being completed with long intervals and complex completion equipment, such as limited entry liners and inflow control devices (ICDs). Accurate modeling and understanding of fluid placement during a stimulation operation through such long complex completions can be quite challenging. In this paper, an integrated approach of modeling, experiments and computational fluid dynamics (CFD) simulations will be presented. A computational tool based on a transient one-dimensional (1D) approach has been developed in-house to model stimulation through such completions. In order to validate the 1D approach for reliable fluid displacement predictions, annulus fluid displacement experiments in perforated liners supported by CFD simulations have been conducted. The experimental setup consists of an outer Lucite pipe representing the well-bore geometry and an inner aluminum pipe with multiple perforations of variable diameter. The setup mimics the real field application in a 1:1 scale with respect to the pipe and perforation diameters while the test section is limited to 27 ft. The experimental procedure is as follows: fluid is pumped into the annulus through the perforations until the annulus is completely filled,the fluid tank is switched "on-the-fly" to the tank with the displacing fluid resulting in the displacement of the annulus fluid by the displacing fluid through the perforations. The experiments and the CFD simulations indicate that even with a single open perforation inside the 27-ft test section, the three-dimensional (3D) flow field around the perforation rapidly transitions to uniform annular flow within a few feet uniformly displacing the annulus fluid. The model also provides insight into various well injection processes in sandstone and carbonate formation, such as scale squeezes, solvent treatments, and HF acid treatments. Introduction The length of production and injection intervals in a single well continues to increase in order to contact more reservoir rock with a single wellbore penetration and improve project economics. Multiple, thick stacked reservoirs are accessed by vertical and deviated wells while thinner reservoirs are being exploited with longer and longer horizontal wells1–3. To keep up with drilling capability, completion technology has advanced considerably in the past few years. Horizontal wells are "compartmentalized" using mechanical and/or swellable packers. Within a given compartment, injection and production can be controlled by use of inflow control devices (ICDs), limited entry (LE) liners, and/or sliding sleeves. The liners also make it easier to enter the completion interval with logging tools, wire line, and coiled tubing. While various tools are available to evaluate long-term, steady-state production and injection into such wells, modeling of short-term, transient injection into such completions is very challenging due to the long lateral lengths, limited entry points from the liner to each compartment, and the presence of an open annulus with occasional packer isolations. This is especially important for long wells in carbonate formations as all wells require acid stimulation upon initial completion, and occasionally throughout the well life.

CFD data based neural network functions for predicting hydrodynamic performance of a low-pitch marine cycloidal propeller

The chemical composition and properties of fuels used in compression-ignition engines can influence engine performance significantly. Consequently, the modeling of fuel chemistry within computational fluid dynamics (CFD) simulations of diesel and other compression ignition engines is important. Modern detailed chemical mechanisms may provide predictive modeling of fuel chemistry; however, they are generally far too computationally expensive for use in CFD. We present simulations of diesel engine combustion, focusing on the prediction of ignition, using the CONVERGE CFD software package. A CFD simulation framework with models for turbulence and spray breakup and atomization is presented with a reduced global reaction model to describe fuel oxidation and ignition. The global reaction model incorporates a single parameter, the derived cetane number (DCN), to describe fuel reactivity variability. CFD simulations are compared to experiments carried out in a single-cylinder diesel engine for compositionally diverse conventional and alternative diesel and jet fuels. Model-experiment comparisons show general agreement for ignition timing and the influence of fuel variability on ignition timing. In addition, the sensitivity of CFD predictions on the chemistry, turbulence, and spray models is illustrated.

The removal of toxic gases leaking during excavation in infrastructure projects is crucial for both human health and environmental protection. In this process, Computational Fluid Dynamics (CFD) simulations are highly valuable for modeling and analyzing complex physical processes associated with the transport and dispersion of gases. During infrastructure projects in geothermal regions, various gases may leak from underground sources. These gases may include toxic and/or flammable substances such as hydrogen sulfide (H₂S), carbon dioxide (CO₂), and methane (CH₄). Designing an effective ventilation system is essential for the removal of toxic gases through ventilation. CFD simulations can be utilized to evaluate the design and performance of ventilation systems. Modeling gas leaks from sources encountered during excavation using CFD simulations can help understand how gases move throughout infrastructure projects and their environmental impacts. CFD simulations can assist in optimizing factors such as the placement of ventilation systems, duct design, air flow rates, and filtration efficiency. This optimization ensures the effective removal of toxic gases and minimizes environmental impacts. CFD simulations can also be used to assess the efficiency and safety of ventilation systems designed for the mitigation of toxic gases. Additionally, simulating the operation of ventilation systems during potential emergency situations can help in evaluating associated risks.

In response to a solicitation for Computational Fluid Dynamic (CFD) simulations of flow in a T-junction from the Nuclear Energy Agency of the Organization for Economic Co-operation and Development (OECD/NEA) [1], Structural Integrity (SI) Associates of San Jose, CA, USA has completed a simulation using the commercially available CFD code ANSYS-CFX. The simulation was carried out for geometry and flow conditions matching an experiment underway at Vattenfall Research and Development in Sweden where two streams of differing temperature mix in a T-junction. The benchmark was to be a blind test of CFD simulations. Experimental results were not released until after benchmark participants submitted the results of their simulation to the OECD/NEA. The CFD simulation done by SI was carried out on an all hexahedral mesh of 1,881,504 elements generated using the ANSYS Mechanical Finite Element program. The mesh was then transferred into the CFX program and, after applying proper boundary conditions, a time-dependent simulation was done using the Large Scale Eddy Simulation (LES) turbulence model [2] with Wall Adjusting Local Eddy Viscosity (WALE) sub-grid scale (SGS) turbulence model [2, 3]. Comparisons of the CFD results to the Vattenfall data show close correspondence for mean and root-mean-square (rms) turbulent temperature fluctuations.

CFD simulation and experimental validation of a GM type double inlet pulse tube refrigerator

Recently, image-based computational fluid dynamic (CFD) simulations have been proposed to investigate the local hemodynamics inside human cerebral aneurysms. It was suggested that the knowledge of the computed three-dimensional flow fields can be used to assist clinical risk assessment and treatment decision making. Therefore, it was desired to know the reliability of CFD for cerebral blood flow simulation, and be able to provide clinical feedback. However, the validations were not yet comprehensive as they lack either patient-specific boundary conditions (BCs) required for CFD simulations or quantitative comparison methods. In this study, based on a recently proposed in-vitro quantitative CFD evaluation approach via virtual angiography, the CFD evaluation was extended from phantom to patient studies. In contrast to previous work, patient-specific blood flow rates obtained by transcranial color coded Doppler ultrasound measurements were used to impose CFD BCs. Virtual angiograms (VAs) were constructed which resemble clinically acquired angiograms (AAs). Quantitative measures were defined to thoroughly evaluate the correspondence of the detailed flow features between the AAs and the VAs, and thus, the reliability of CFD simulations. The proposed simulation pipeline provided a comprehensive validation method of CFD simulation for reproducing cerebral blood flow, with a focus on the aneurysm region. Six patient cases were tested and close similarities were found in terms of spatial and temporal variations of contrast agent (CA) distribution between AAs and VAs. For patient #1 to #5, discrepancies of less than 11% were found for the relative root mean square errors in time intensity curve comparisons from characteristic vasculature positions. For patient #6, where the CA concentration curve at vessel inlet cannot be directly extracted from the AAs and given as a BC, deviations about 20% were found. As a conclusion, the reliability of the CFD simulations was well confirmed. Besides, it was shown that the accuracy of CFD simulations was closely related to the input BCs.

Speeding up CFD simulation of fluidized bed reactor for MTO by coupling CRE model

To evaluate manoeuvring performance of merchant ships, the mathematical modeling group (MMG) or computational fluid dynamics (CFD) simulations are used. However, it is difficult to use the MMG to evaluate the manoeuvring performance of fishing vessels, thus research using CFD simulations is necessary. Also, since the course-changing and turning ability is crucial in fishing operations, a rudder design suitable for fishing vessels is necessary. This study designs a rudder using National Advisory Committee for Aeronautics (NACA) airfoil sections and evaluates its manoeuvring performance. A CFD model is used to evaluate the manoeuvring performance of the fishing vessel, and turning and zig-zag tests are conducted. The effectiveness of using CFD simulations based on Reynolds averaged Navier-Stokes equations to assess the manoeuvring performance of fishing vessels was validated. No significant difference was found in the manoeuvring performance for hull forms and rudder designs for course-changing ability. However, the original hull form showed superior turning performance. Among five rudders with varying aspect ratios and shapes, the rudder with 5.5% aspect ratio had the best turning performance. Regarding the rudder design for fishing vessels, NACA airfoil was employed, and a rudder aspect ratio of 5.5% based on the immersed hull side area is recommended.