The aerodynamics performance of Blended Wing Body Baseline-II E2

Kenyalang is a fuel cell powered Unmanned Aerial Vehicle (UAV) developed by Universiti Teknologi MARA (UiTM). This paper discusses the aircraft performances analysis of Kenyalang. Computational Fluid Dynamic (CFD) using Numeca software had been performed to obtain the aerodynamics characteristic of the Kenyalang UAV in the form of lift (CL) and drag (CD) coefficients. Unstructured mesh and standard one - equation turbulence model, and Spalart-Allmaras selected in the simulation. Lift coefficients (CL) and drag coefficients (CD) were studied at flight condition of Mach 0.08 (~26 m/s) at different angles of attack, α. The CFD data results were used to obtain Stall Speed, Take off Distance and Rate of Climb, and the results are shown in this paper.

This study examines the aerodynamic performance of a NACA 4412 airfoil that is covered with denticles, comparing it to a smooth NACA 4412 airfoil. The aim was to assess the lift-to-drag ratio of the airfoil utilizing biomimetic surfaces inspired by the dermal denticles of Isurus oxyrinchus. To achieve this, the airfoils were subjected to testing in a wind tunnel. Both the denticles-covered and smooth airfoils, measuring 355 by 184 mm, were equipped with 27 pressure taps distributed across three spanwise sections: the leading edge, upper surface, and lower surface. Nine flexible tubes were connected to pressure sensors for each row of static taps. Wind tunnel tests were conducted at various angles of attack (AOAs), ranging from −10.8° to 16.2° with an increment of 1.8°. Testing was carried out at wind speeds of 3, 6, and 9 m/s. Computational fluid dynamics (CFD) simulations were conducted on the smooth airfoil under identical conditions to validate the wind tunnel testing setup. The lift and drag coefficients were derived from the recorded static pressures. A comparison between the aerodynamic coefficients obtained from experiments and CFD simulations indicated that higher wind speeds are preferable for wind tunnel testing as they yield more consistent results. When examining the aerodynamic coefficients of the smooth airfoil compared to the denticle-covered airfoil, it was found that the latter generally produced higher lift and drag, resulting in a lower lift-to-drag ratio across different angles of attack and wind speeds. Specifically, at 3 m/s, the denticle-covered airfoil exhibited better lift at most AOAs, higher drag at certain AOAs, and improved lift-to-drag ratios. At wind speeds of 6 and 9 m/s, the denticle-covered airfoil demonstrated higher lift for all tested AOAs and increased drag for several AOAs, yet it consistently had lower lift-to-drag ratios. These findings point to the potential benefits of utilizing the denticle-covered NACA 4412 airfoil due to its enhanced lift characteristics at lower wind speeds. Further research is warranted to quantify the differences between the airfoil types.

Aerodynamic characteristics of a guided rocket projectile are numerically simulated. Simulations are performed in a range of flight conditions using a commercial CFD software FLUENT, and variations of lift coefficients and drag coefficients with Mach numbers and angles of attack were demonstrated. The numerical results also indicate that the angle of canard deflection has significant influence on the flow field near tailfins.

A “credible” computational fluid dynamics (CFD) model has the potential to provide a meaningful evaluation of safety in medical devices. One major challenge in establishing “model credibility” is to determine the required degree of similarity between the model and experimental results for the model to be considered sufficiently validated. This study proposes a “threshold-based” validation approach that provides a well-defined acceptance criteria, which is a function of how close the simulation and experimental results are to the safety threshold, for establishing the model validity. The validation criteria developed following the threshold approach is not only a function of Comparison Error, E (which is the difference between experiments and simulations) but also takes in to account the risk to patient safety because of E. The method is applicable for scenarios in which a safety threshold can be clearly defined (e.g., the viscous shear-stress threshold for hemolysis in blood contacting devices). The applicability of the new validation approach was tested on the FDA nozzle geometry. The context of use (COU) was to evaluate if the instantaneous viscous shear stress in the nozzle geometry at Reynolds numbers (Re) of 3500 and 6500 was below the commonly accepted threshold for hemolysis. The CFD results (“S”) of velocity and viscous shear stress were compared with inter-laboratory experimental measurements (“D”). The uncertainties in the CFD and experimental results due to input parameter uncertainties were quantified following the ASME V&V 20 standard. The CFD models for both Re = 3500 and 6500 could not be sufficiently validated by performing a direct comparison between CFD and experimental results using the Student’s t-test. However, following the threshold-based approach, a Student’s t-test comparing |S-D| and |Threshold-S| showed that relative to the threshold, the CFD and experimental datasets for Re = 3500 were statistically similar and the model could be considered sufficiently validated for the COU. However, for Re = 6500, at certain locations where the shear stress is close the hemolysis threshold, the CFD model could not be considered sufficiently validated for the COU. Our analysis showed that the model could be sufficiently validated either by reducing the uncertainties in experiments, simulations, and the threshold or by increasing the sample size for the experiments and simulations. The threshold approach can be applied to all types of computational models and provides an objective way of determining model credibility and for evaluating medical devices.

Computational fluid dynamic (CFD) simulations in support of the SHARP-B2 (Slender Hypervelocity Aerothermodynamic Research Probes) program are presented. Pre-flight simulations of the aerothermal flight environment have been made to aid in the design of the flight hardware and instrumentation. Simulations of a critical flight qualification ground test performed in the 20 MW Panel Test Facility (PTF) arc jet, which is equipped with a semi-elliptical nozzle, have also been performed. The arc jet simulations were performed with the same CFD code that is used in the flight calculations. For both the flight and the arc jet simulations, the CFD results are used to provide surface heat transfer coefficients that serve as boundary conditions for an in-depth conduction thermal response code. By using the same CFD tool to compute the aerothermal environments for both the ground test and the flight test environment, useful comparisons are made regarding the traceability of the ground test environment to flight. Introduction The NASA Ames Research Center has been developing new Ultra High Temperature Ceramics (UHTC's) with the goal that these materials will enable sharp leading edges to be used for future space vehicles. Because of their unique thermo-structural properties, these materials are capable of operation at temperatures near 5100 °F without ablation. The materials have been developed and tested in ground-based arc jet facilities, and a flight test program designated SHARP (Slender Hypervelocity Aerothermodynamic Research Probes) has been initiated. The first flight demonstration, SHARP-B1, incorporated a UHTC nosetip mounted on a U.S. Air Force Mkl2A entry vehicle in collaboration with Sandia National Laboratory (SNL), and was successfully flown in May, 1997. The second flight test, SHARP-B2, which incorporated four instrumented UHTC strakes mounted on the side of the entry vehicle, was flown in September 2000. The goal of these flight tests is to assess the performance of the materials under entry conditions. The use of Computational Fluid Dynamic (CFD) simulations for the design of Thermal Protection Systems (TPS) has evolved to an extent that they have been integrated into the preliminary design process of Reusable Launch Vehicle (RLV) programs such as the X-33. Real-gas CFD simulations with finite-rate chemistry and proper boundary conditions for coupling with material thermal response codes are now routinely performed on high-end laboratory workstations. Much of the ground based testing of advanced TPS components is done in arc-heated test facilities such as those located in the Arc Jet Complex at the NASA Ames Research Center. These facilities are capable of simulating the high enthalpy flow environment experienced by entry vehicles for a broad range of test conditions and configurations. Semi-elliptical nozzles are available for the testing of flat panels in a high enthalpy boundary layer environment. CFD is • Aerospace Engineer, Reacting Flow Environments Branch, Member AIAA. t Senior Research Scientist, ELORET, Member AIAA. Copyright © 2001 by the American Institute of Aeronautics and Astronautics, Inc. No copyright is asserted in the United States under Title 17, U.S. Code. The U.S. Government has a royalty-free license to exercise all rights under the copyright claimed herein for Governmental Purposes. All other rights are reserved by the copyright owner. (c)2001 American Institute of Aeronautics & Astronautics or Published with Permission of Author(s) and/or Author(s)' Sponsoring Organization.

Experimental Fluid Dynamics (EFD) and Computational Fluid Dynamics (CFD) have been instrumental in Fluid Mechanics to help solve scientific and engineering problems. This research attempts to use both techniques to perform a parametric study of turbulence flow around airfoil ClarkY-14 at various velocity and angle of attack (AoA). Clark Y-14 airfoil was designed in the 1920’s. It demonstrated good overall performance at low and moderate Reynolds numbers. With the progress in the aviation field, its performance was sub-optimal for newer aircraft designs. However, with the advent of RC airplanes and model aircrafts, there is a renewed interest in this airfoil. Various research projects have been conducted using this airfoil, but there hasn’t been a combined EFD and CFD study of the performance characteristics of the airfoil itself, which still finds real world applications today. One important aspect of this research included the investigation of the effects of a Force Measurement Device/Sensor, which is typically used in scaled/full-size wind tunnels to mount the test model as well as measure the forces/moments acting on it during the testing. The presence of such a device could affect the quality of the data obtained from the wind tunnel testing when compared to a real world application scenario where the aforementioned device may not be present. To the best of the author’s knowledge, no detailed study has been published on the effects of such devices. In this study, the results with and without the measuring device were generated by using CFD simulations. The results were then compared to see to what extent the inclusion of these devices will affect the results. The methodology used for this research was experimental as well as computational. In the present research, a commercially available CFD software STAR-CCM+ was employed to simulate the flows around airfoil Clark Y-14. The experimental data was obtained from wind tunnel tests using AEROLAB Educational Wind Tunnel (EWT) and compared with the simulation data from the CFD. The two data sets were in good agreement. Both experimental and simulation results were used to understand the effects of the measurement device/sensor used in the scaled wind tunnel on the lift and drag coefficients of the airfoil. Two separate CFD simulation setups were designed to model the presence and absence of the measurement device/sensor. These setups replicated the wind tunnel setup. The airfoil was tested and simulated at different speeds as well as different AoA. The comparative study gave a useful insight on the accuracy of the CFD simulations in relation to the actual testing. The analysis of results concluded that the force measurement device/sensor had insignificant effects on the accuracy and quality of data collected through wind tunnel testing.

Several studies based on in vivo or in vitro models have found promising results for the noble gas argon in neuroprotection against ischaemic pathologies. The development of argon as a medicinal product includes the requirement for toxicity testing through non-clinical studies. The long exposure period of animals (rats) during several days results in technical and logistic challenges related to the gas administration. In particular, a minimum of 10 air changes per hour (ACH) to maintain animal welfare results in extremely large volumes of experimental gas required if the gas is not recirculated. The difficulty with handling the many cylinders prompted the development of such a recirculation-based design. To distribute the recirculating gas to individually ventilated cages and monitor them properly was deemed more difficult than constructing a single large enclosure that will hold several open cages. To address these concerns, a computational fluid dynamics (CFD) analysis of the preliminary design was performed. A purpose-made exposure chamber was designed based on the CFD simulations. Comparisons of the simulation results to measurements of gas concentration at two cage positions while filling show that the CFD results compare well to these limited experiments. Thus, we believe that the CFD results are representative of the gas distribution throughout the enclosure. The CFD shows that the design provides better gas distribution (i.e. a higher effective air change rate) than predicted by 10 ACH.

This work describes the aerodynamic characteristics of an aircraft wing model with a Rüppell’s griffon vulture (RGV)-type winglet. A computational fluid dynamics (CFD) study using ANSYS 15.0 was conducted to study the effect of the RGV winglet on a rectangular wing. The NACA 65(3)-218 wing consists of 660 mm span and 121 mm chord length where the aspect ratio is 5.45. Eight different winglet configurations have been studied. Furthermore, the study is extended to study effect of cant angle and different angles of attack (AOA) to the winglet. A comparative study is done on aerodynamic features such as lift coefficient (CL), drag coefficient (CD), lift/drag ratio (CL/CD) and tip vortices to get the best RGV winglet design. The RGV winglet achieved highest CL compared to other types of winglets configuration. Based on contour plot analysis, the RGV winglet shows lower vortex formation compared to without winglet. The results show about 15 to 30% reduction in drag coefficient and 5 to 25% increase in lift coefficient by using an RGV winglet.

Evaluation and verification of patient-specific modelling of type B aortic dissection

A computational fluid dynamics (CFD) analysis is conducted on the flow of Newtonian and non-Newtonian fluids in annuli including the effect of inner pipe rotation. A practical numerical model is proposed that accurately estimates the annular frictional pressure losses with and without the inner pipe rotation. Experiments are conducted at a 91 ft. long flow loop using various fluids that can be characterized as Yield Power Law (YPL). A commercial CFD software is used to validate the proposed numerical approach. A comprehensive comparison of the proposed model, CFD results, experimental results, the published experimental results and most widely used models from the literature is presented. The experimental setup simulates horizontal wellbore applications, which are increasingly prevalent due to recent shale plays. Today, since most drilling fluids show YPL behavior, YPL fluids with a wide range of rheological properties are used as test fluids in this study. The numerical model is coupled with a stability criterion that determines the onset and offset of the transitional flow between laminar and turbulent regions. The velocity profiles of a wide range of diameter ratios, Taylor and Reynolds numbers are presented. Various degrees of eccentricity are analyzed in terms of pressure profile and flow stability with the proposed method. The results from the experiments show significantly reduced pressure drops in fully eccentric annuli compared to concentric geometry. An increase in pressure loss is observed as the pipe is rotated while it is eccentric. The comparisons between the models indicate that the slot approximation can result in large errors especially when the diameter ratio is low. A 3D wellbore can be evaluated with grids using the proposed numerical method and the local stability criterion, which leads to accurate pressure loss estimations. Grid analysis can show the flow state profile and the pressure loss profile of a wellbore, which has potential to optimize operations in real-time or in the design phase. This study contributes to a better understanding of flow in annuli. The results obtained from this study are useful to predict the transition and the annular frictional pressure loss profiles more accurately than existing methods. Potential applications include risk avoidance and optimized operations.

Introduction: We examined the viability of pairing wire-obtained flow pressure data with computational fluid dynamic (CFD) analysis for accurate patient-specific 3D reconstruction of flow through cerebral vessels—an approach that provides comprehensive velocity data and other flow parameters to assist the preventative diagnosis of cerebral stenosis. Methods: Two physical phantom models of a cerebral stenosis—differing in regard to vascular morphology at and around the stenosis—were prepared, filled with physiological saline and connected individually to a flow pump (Vascular Simulations LLC Left Heart Replicator) applying pulsatile flow. Pressure measurements were taken upstream of the stenosis by microcatheter-guided wires to define an inlet boundary condition for CFD analysis. Pressure and velocity at 2 cm proximal to stenosis, the stenosis inlet, the stenosis outlet, and 2 cm distal to stenosis were measured to validate the CFD simulated flow. Results: Excellent agreement was observed between CFD and wire-measured time-dependent flow pressure, with the expected pulsatile behavior observed at each location. Between the two methods, differences in maximum systolic pressures ranged between |0.73±0.72|% and |3.90±0.74|%. Differences in minimum diastolic pressures ranged between |1.79±1.33|% and |9.08±1.42|%. Velocity data from wire measurements lacked pulsatile behavior and showed differences ranging between |2.93±5.20|% and |120.10±2.91|% from CFD-obtained measurements, which did show correct pulsatile behavior. Larger discrepancies were strongly associated with areas of higher CFD predicted velocities (r=0.86). Conclusion: Guidewire flow measurements provided CFD analysis with accurate inlet boundary conditions and validated CFD simulation results. CFD analysis allowed for detailed visualization of key flow parameters that may be difficult to physically measure—such as velocity—that are relevant for understanding risk factors associated with cerebral stenosis on a case-by-case basis.

Mechanical Heating Ventilation and Air-Conditioning (HVAC) systems account for 60% of the total energy consumption of buildings. As a sector, buildings contributes about 40% of the total global energy demand. By using passive technology coupled with natural ventilation from wind towers, significant amounts of energy can be saved, reducing the emissions of greenhouse gases. In this study, the development of Computational Fluid Dynamics (CFD) analysis in aiding the development of wind towers was explored. Initial concepts of simple wind tower mechanics to detailed design of wind towers which integrate modifications specifically to improve the efficiency of wind towers were detailed. From this, using CFD analysis, heat transfer devices were integrated into a wind tower to provide cooling for incoming air, thus negating the reliance on mechanical HVAC systems. A commercial CFD code Fluent was used in this study to simulate the airflow inside the wind tower model with the heat transfer devices. Scaled wind tunnel testing was used to validate the computational model. The airflow supply velocity was measured and compared with the numerical results and good correlation was observed. Additionally, the spacing between the heat transfer devices was varied to optimise the performance. The technology presented here is subject to a patent application (PCT/GB2014/052263).

Aerodynamic characteristics of an Ejection Seat System at different angles of attack are studied by the numerical method and the flow mechanisms for such flows are carefully analyzed. The governing equations are Reynolds-averaged Navier-Stokes equations which are solved by the unstructured finite volume method. Upwind Osher scheme is used for spatial discretization and five-stage Runge-Kutta scheme is applied for temporal discretization. The DES model based on S-A one equation turbulence model is adopted. Parallel computation is based on the domain decomposition method and multi-block is achieved by using METIS system. The experimental data is used to validate this method. This research is helpful to understand the aerodynamic characteristics and flow mechanisms of Ejection Seat System at different angles of attack and Mach numbers, and can provide reasonable reference for Ejection Seat System design.

The aim of this study is to investigate the use of computational fluid dynamics (CFD) in evaluating the thermal performance of a parallel/counterparallel flow heat exchanger used as part of a fluid warmer to treat hypothermia. The developed CFD model was validated in a parametric study using previously collected experimental data. The effects of heat exchanger length and inlet mass flow rate were considered. To more accurately represent the thermodynamic average temperature profile, the current CFD analysis evaluated outlet temperatures in terms of mean bulk temperature as opposed to the centerpoint temperature probe used in the experimental study. Despite this difference, the CFD results were found to agree well with the experimental values. As such, the CFD simulations are not only applicable to future design considerations but elicit further understanding of the thermal and hydrodynamic characteristics within the heat exchanger. Using the validated CFD model, thermal hydraulic entrance lengths ...

We recently proposed a technique for preparing monodisperse emulsions with a coefficient of variation below 5% from a silicon array of micrometer-sized channels perpendicular to the plate surface, named a straight-through microchannel (MC). This study involved three-dimensional computational fluid dynamics (CFD) simulations to calculate the formation of an oil-in-water (O/W) emulsion droplet from straight-through MCs with circular and elliptic cross sections. The CFD results demonstrated that the oil phase that passed through the elliptic MCs exceeding a threshold aspect ratio between 3 and 3.5 was cut off spontaneously into a small droplet with a diameter of approximately 40 microm. Sufficient space for water at the channel exit had to be maintained for successful droplet formation. The formation and shrinkage of a neck inside the channel caused an increased pressure difference inside the channel and an increased velocity value near the neck. The pressure and velocity values at the neck drastically changed, and the neck was cut off instantaneously just before the completion of droplet formation. This process was triggered by a gradually increased pressure difference between the circular neck and inflating oil phase. The findings obtained in this paper provide useful numerical and visual information about the droplet formation phenomena from the straight-through MCs. The CFD results were verified by the experimental results, showing that the CFD approach can help design a suitable channel structure.