- Research Article
87
- 10.1016/j.applthermaleng.2016.03.119
Optimization of thermal design of ribbed flat-plate fin heat sink
- Apr 06, 2016
- Applied Thermal Engineering
- Hamdi E Ahmed
Optimization of thermal design of ribbed flat-plate fin heat sink
Abstract Genetic algorithms (GAs) are considered to be one of the main types of evolutionary algorithms (EAs) and are being increasingly used in various engineering design applications. To a large extent, plate-fin heatsinks are used in the thermal management of compact electronic equipment and data centers. The shape optimization of the heatsinks is not rigorously investigated during the design process of high power electronics. Any improvements in the effectiveness of the heatsinks impact the energy consumed by large-scale information communication technology (ICT) facilities including data centers and telecommunication systems and promote a more sustainable use of raw materials. This paper investigates the optimization of plate-fin heatsinks by modifying the fin layout in a forced crossflow using a multi-objective genetic algorithm (MOGA) combined with computational fluid dynamics (CFD) simulations. The main objective is to improve the heat dissipation rate by modifying geometric parameters, i.e., the number, arrangement, and orientation of fins. For a generic heatsink test case, the optimized performance is examined in terms of thermal resistance, turbulence intensity, pumping power, coefficient of performance, and Chilton–Colburn j-factors. Among all of the cases investigated, the input parameter optimization configurations which coupled and rotated fins in groups of ten proved to be the most successful. For one case, an 18% increase in the effectiveness of heat dissipation is reported. However, when weight reduction was considered by dividing by the unit mass, the designs in one of the investigated families which remove a number of fins from the heatsink outperformed the rest, achieving improvements of 65% over the baseline.
Optimization of thermal design of ribbed flat-plate fin heat sink
Optimization of thermal design of ribbed flat-plate fin heat sink
Optimization design by evolutionary computation for minimizing thermal stress of a thermoelectric generator with varied numbers of square pin fins
Optimization design by evolutionary computation for minimizing thermal stress of a thermoelectric generator with varied numbers of square pin fins
Read moreNumerical investigation of heat transfer enhancement in plate-fin heat sinks: Effect of flow direction and fillet profile
Many researchers have studied the thermal performance of heat sinks, however to the best knowledge of the authors, the effect of flow direction (place of fan) on the thermal performance of plate-fin heat sinks with fillet profile have not yet been investigated. In this paper, the investigation develops a computational fluid dynamics (CFD) model, validated through comparison with an experimental data from the literature, which demonstrates the effect of flow direction and fillet profile on the thermal performance of plate-fin heat sinks. In particular, a plate-fin heat sink with fillet profile subject to parallel flow has been compared with the conventional design (plate-fin heat sink without fillet profile subject to an impinging flow) and satisfactory results have been perceived. The results of this study show that the base temperature along with the thermal resistance of the heat sink is lower for the proposed design. Therefore, the developed approach has strong potential to be used to improve the thermal performance of heat sinks and hence to develop more advanced effective cooling technologies.
Read moreDesign optimization of plate-fin heat sink with forced convection for single-module thermoelectric generator
Design optimization of plate-fin heat sink with forced convection for single-module thermoelectric generator
A Numerical Study of a Heat Sink Fin Under a Laminar Impinging Jet
Impinging jet heat transfer is a promising method to cool electronic components. In this paper, a numerical study has been carried out to examine the conjugate heat transfer under a confined impinging jet using a plate-fin heat sink as the target plate. Effects of geometric parameters such as fin number, fin height, and fin-to-spacing ratio are examined over a range of jet Reynolds numbers using dielectric fluid FC-72 as the fluid medium. Thermal resistance, pressure drop, and Nusselt number are the main criteria used to evaluate the thermal and fluid dynamic performance of this flow system. Furthermore, the effects of fin height, fin-to-spacing ratio, and jet Reynolds number on impinging jet heat transfer are obtained. The concept of an effective Nusselt number is introduced for computing the heat transfer effectiveness of heat sinks with different fin numbers.
Read moreMelting process enhancement in double pipe storage with multiple latent heat storage materials and oriented fins
Melting process enhancement in double pipe storage with multiple latent heat storage materials and oriented fins
ANALYSIS OF PLATE-FIN HEAT SINK INFUSED WITH PHASE CHANGE MATERIALS FOR INTERMITTENT SPACE MISSIONS
In this work, we numerically investigated the heat transfer effectiveness of different phase change materials (PCMs) when infused in a plate-fin heat sink with a fixed volume fraction of thermal conductivity enhancer. The PCM's ability to absorb and release large amounts of thermal energy at constant temperature is a desired feature in transient electronics cooling applications. In this study, we focused on examining the effect of the number of fins, type of PCM, heat flux, PCM volume fraction, and heat sink bottom wall thickness. The results showed that increasing the number of fins improved the performance of the PCM-infused heat sink. When a heat flux of 4000 W/m<sup>2</sup> was applied for 30 minutes on a plate-fin heat sink infused with paraffin wax, the maximum temperature did not exceed 70&deg;C in the four-fin design, while it exceeded 80&deg;C in the two-fin design. A salt hydrate PCM outperformed paraffin wax and RT35. The bottom wall of the heat sink acted as a thermal spreader and a nonlinear relationship existed between the bottom wall thickness and the maximum electronics temperature. Compared to the two- and four-fin heat sink models, the zero-fin model required the longest time to fully melt the entire PCM due to the additional amount of PCM present in the heat sink gaps.
Read moreOptimal Arrangement Design of a Tube Bundle in Cross-Flow Using Computational Fluid Dynamics and Multi-Objective Genetic Algorithm
Recently, energy saving problem attracts increasing attention from researchers. This study aims to determine the optimal arrangement of a tube bundle to achieve the best overall performance. The multi-objective genetic algorithm (MOGA) is employed to determine the best configuration, where two objective functions, the average heat flux q and the pressure drop Δp, are selected to evaluate the performance and the consumption, respectively. Subsequently, a decision maker method, technique for order preference by similarity to an ideal solution (TOPSIS), is applied to determine the best compromise solution from noninferior solutions (Pareto solutions). In the optimization procedure, all the two-dimensional (2D) symmetric models are solved by the computational fluid dynamics (CFD) method. Results show that performances alter significantly as geometries of the tube bundle changes along the Pareto front. For the case 1 (using staggered arrangement as initial), the optimal q varies from 2708.27 W/m2 to 3641.25 W/m2 and the optimal Δp varies from 380.32 Pa to 1117.74 Pa, respectively. For the case 2 (using in-line arrangement as initial), the optimal q varies from 2047.56 W/m2 to 3217.22 W/m2 and the optimal Δp varies from 181.13 Pa to 674.21 Pa, respectively. Meanwhile, the comparison between the optimal solution with maximum q and the one selected by TOPSIS indicates that TOPSIS could reduce the pressure drop of the tube bundle without sacrificing too much heat transfer performance.
Read moreDeep learning for both broadband prediction of the radiated emission from heatsinks and heatsink optimization
Deep learning for both broadband prediction of the radiated emission from heatsinks and heatsink optimization
2-Dimensional CFD simulation and correlation development for optimization of fin heatsinks in electronic cooling
CFD has penetrated into the field of electronic cooling for some time. Both parallel and staggered plate fin heatsinks are widely used in modern computers. This paper presents the ways to make most use of CFD in optimization design of those heatsinks: the flow and heat transfer of staggered and parallel plate fin heatsinks of various geometry were simulated by using Fluent 5.0 commercial CFD code. Based on 60 different simulation solutions, two correlations, concerning Nusselt number and friction factor as the functions of geometrical and operational parameters of the heatsinks were developed. The presentation parameter examination was also performed by comparing the numerical solutions with the analytical solutions of parallel plate arrays, showing that the correct parameters are used in the correlations.
Read moreEffect of condensing unit layout at building re-entrant on split-type air-conditioner performance
Effect of condensing unit layout at building re-entrant on split-type air-conditioner performance
Design Investigation on Flow Diffuser With Code_Saturne: CFD Simulation Analysis
The flow rate distribution at the entrance of the core plays a key role for reactor design since it has important implications for the performance, and efficient safety of a nuclear reactor. When the coolant passes from the downcomer to the core, it changes direction due to the inertia force and the curvature of the bottom vessel head. The internal components inside lower plenum work to homogenize the flow distribution. Their purpose is to prevent the formation of instabilities and the creation of vortices due to the flow reversal. In the frame of EDF’s new reactor design there is a desire to identify an optimal flow diffuser. The future intention is to study five different types of flow diffuser including EPR, VVER, Konvoï, APR+ and Westinghouse to look at the pros and cons of each design. The authors underline that the geometries of each Reactor Pressure Vessel (RPV) and associated diffuser device are quite different therefore a generic form needs to be used to make an equivalent comparison. The goal of the present work is to find the optimal mesh refinement and associated numerical parameters for the simulation of the lower plenum flow. This work is a preliminary step for a future study to compare existing diffuser concepts. Thus in the future work only the section containing the flow diffuser structure will be changed. The PIRT methodology is applied to better define the physical phenomena and key parameters that will influence the flow distribution at the entrance of the core. In order to better understand the fluid distribution and the function of the diffuser component, 3D computational fluid dynamics (CFD) simulations are launched to improve our knowledge on the flow pattern inside the lower plenum. Both the geometry and mesh are generated by Salomé1. Simulations are carried out using Code_Saturne2, an EDF in-house open-source CFD code. The generic test case is a 1/5 scale EDF “BORA” 4 loop mock-up with a flow rate of 0.1 m3/s injected into each cold leg. The unsteady flow algorithm with standard k-epsilon turbulence model has been used with a full explicit meshing except for the reactor core where a porous approach is adopted. The physical time for each calculation case is 5s for a converged simulation. Mesh sensitivity tests have been carried out ranging from 8 million cells to 28 million cells. A mesh of 22 million cells is found to provide the most appropriate balance between simulation quality and feasibility. Due to the size of the simulations, high performance computers are necessary to provide timely results. The results indicate that CFD can provide extra capacity to engineers for reactor design to evaluate the pros and cons of different existing diffuser concepts.
Read moreThermal performance investigation and optimisation of fin type solar air heater - a CFD approach
In this paper, single pass fin type solar air heater has been optimised to get better thermal performance using computational fluid dynamics (CFD) technique (Fluent 6.3 and Gambit 2.3). Four important parameters namely mass flow rate, number of fins, fin height and length have been considered. DTRM and RNG k-ε turbulence model were used and the simulation results have been validated with the results of experimental study performed during March, 2012. During the CFD analysis outlet air temperature, air temperature rise, heat gain by the air and instantaneous efficiency has been determined. Simulation results suggest that the SAH should have four fins, i.e., same as in existing SAH but fin length and height should increase from 40 cm to 50 cm and 4 cm to 6 cm respectively for superior performance. In optimised SAH, instantaneous efficiency and useful heat gain improved by 8.35% and 8.24% respectively with air mass flow rate of 0.024 kg/s as compared to SAH.
Read moreCFD Analysis and Shape Optimization of NACA0012 Airfoil for Different Mach Numbers
Multidisciplinary design optimization techniques become more and more applied in the field of aerodynamics due to the rapid development of computers high-performance, numerical methods and optimization algorithms. These techniques coupled with Computational Fluid Dynamics (CFD), which aims to incorporate mathematical relations and algorithms to analyze and solve fluid flow problems, involve the use of those numerical methods and algorithms to improve the fluid flow solutions. CFD analysis of an airfoil determines its ability by producing results such as lift and drag forces, and the application of an optimization algorithm involves improving the shape of this airfoil in order to manipulate the lift and drag coefficients according to the requirements. In this work, a numerical investigation, using ANSYS/Fluent, of two-dimensional transonic flow over a NACA 0012 airfoil was conducted at various Mach numbers and compared with the provided experimental data. The flow to be considered is compressible and turbulent and the solver used is the density based implicit solver, which gives good results for high speed compressible flows. Then a shape optimization algorithm, based on a Multi-Objective Genetic Algorithm, was used in order to obtain an improved performance control of the aerodynamic coefficients of the optimized airfoil.
Read moreDesign and Optimization of a Radial Flow Heat Sink under Free Convection at Steady State Condition
Three dimensional numerical models were developed to make prediction free convection heat transfer at steady state condition from radial flow heat sink. The air was considered as the medium of heat transfer. In radial flow heat sink, heat conducts through base in radial pattern and is uniformly transported to the fins. The Tagucy method was used to investigate the effect of several design parameters such as fin length, fin height, number of fins and heat sink base radius on heat transfer. There are five factors and four levels on each factor were chosen. Sixteen types of model were analyzed to obtain total heat transfer for each model. The result was used to estimate the optimum designed values of the parameters affecting the heat sink efficiency. The reproducibility of the optimum design value was verified. The average rate of heat transfer of optimum model was increased by more than 50 % than the reference model. Finally, the heat transfer data of radial flow heat sink were correlated of several outer radius by an equation.
Read more